Xiaomi Dust Mite Vacuum Cleaner Pro

Safety Precautions

Please read this user manual carefully before use and keep it for future reference.

Warnings

• This device is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or persons lacking experience and knowledge, unless supervised or instructed by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the device.
• This device is suitable for children aged 8 years and above, and persons with reduced physical, sensory, or mental capabilities or lack of experience/knowledge, provided they have received supervision or instruction on safe use and understand the potential hazards. Children must not play with the device. Cleaning and user maintenance must not be performed by children without supervision.
• If the power cord is damaged, it must be replaced by the manufacturer, its service workshop, or similarly qualified persons to avoid hazards.
• Before cleaning or maintenance, unplug the device from the power outlet.
• The mite vacuum cleaner is equipped with a UV lamp. Do not expose eyes or skin of people or animals to UV radiation, as it can cause damage.
• To avoid burns, do not touch the UV lamp with your hands during or immediately after use.
• Before cleaning the UV lamp, ensure the mite vacuum cleaner is switched off and avoid pressing the On/Off button during cleaning. Otherwise, the device may start suddenly and cause damage.
• Do not use the mite vacuum cleaner outdoors or on wet surfaces. It is only for indoor use on dry surfaces.
• Do not touch the plug or other parts of the mite vacuum cleaner with wet hands.
• Do not use the mite vacuum cleaner to vacuum water, flammable or explosive liquids like gasoline, or solutions with toxic and harmful components like chlorine bleach, ammonia, and drain cleaner.
• Do not use the mite vacuum cleaner to vacuum drywall pieces, ash (e.g., fireplace ash), or smoking/burning materials like coal, cigarette butts, or matches.
• Do not use the mite vacuum cleaner to vacuum hard or sharp objects like glass, nails, screws, or coins that could damage the product.
• Keep the mite vacuum cleaner away from heaters and direct sunlight to prevent fire.
• Avoid prolonged use if the suction inlets, heat dissipation opening, or hot air outlet are blocked, as this may damage the vacuum cleaner.
• Ensure the mite vacuum cleaner is disconnected from the power supply when not in use for extended periods or before performing maintenance or repair work.
• Install the roller brush and dustbin as instructed before use. To avoid mechanical injury, do not touch the roller brush with your hands during operation.
• Use only Xiaomi-approved accessories and spare parts.
• The mite vacuum cleaner is exclusively for cleaning and removing dust mites from home textiles such as mattresses, duvets, pillows, and sofas. Do not use it for any other purpose.
• Do not operate the mite vacuum cleaner for extended periods in the same position, as surfaces like mattresses or sheets may be damaged by UV rays, hot air, or the roller brush.
• Keep the power cord away from sharp objects that could damage it.
• Do not place the mite vacuum cleaner on unstable surfaces like chairs or tables to avoid damage or injury from falling.
• If the vacuum cleaner emits smoke, odors, or powder from the heat dissipation opening, stop use, disconnect from the power supply immediately, and contact customer service.
• Never attempt to disassemble the mite vacuum cleaner yourself. Contact an authorized service center for repairs.
• WARNING: This device contains a UV emitter. Do not look directly into the light source.

Package Contents

• Dust Mite Vacuum Cleaner
• Dustbin Assembly
• User Manual
• Warranty Declaration

Note: Illustrations of the product, accessories, and user interface in the manual are for reference only. Actual products and functions may vary due to product improvements.

Product Overview

Key Components:

• Power Cable
• Mode Button
• On/Off Button
• Display
• Dustbin Release Button
• Dustbin Cover
• Dustbin
• Dustbin Slot
• Roller Brush Cover
• Roller Brush
• Inlet
• UV Lamp Distance Sensor
• Roller Brush Cover Release Button
• UV Lamp
• Hot Air Outlet

Display Indicators

The display features several indicator lights:

• Intelligent Mode Indicator
• Low Suction Indicator
• High Suction Indicator
• Hot Air Drying Indicator
• Ultrasound Indicator
• UV Indicator
• Dust Mite Density Indicator: Green (Low), Yellow (Medium), Orange (High)

Notes:

• Hot air drying, ultrasound, and UV functions are activated by default.
• The UV indicator lights up when the UV function is on and turns off when it's deactivated.
• The UV indicator may turn off when the vacuum cleaner is lifted more than 5 cm from the textile surface, tilted, or when cleaning dark textiles. This is normal.
• A steady yellow or orange dust mite density indicator signifies high mite density in the current area, suggesting multiple passes for cleaning.

Usage

Dustbin Assembly Installation

Align the dustbin slot with the protruding part and push the dustbin down until you hear a "click" indicating it is installed.

Powering On/Off

• Connect the mite vacuum cleaner to the power supply and press the On/Off button to turn it on.
• Upon first use, the device defaults to low suction mode.

Note: Hot air will be emitted from the heat dissipation opening during use. A slight odor from the exhaust port during the first use is normal and will disappear after some usage.

Switching Modes

Turn on the mite vacuum cleaner and press the Mode button to cycle through low suction, intelligent mode, and high suction mode.

• Low Suction Mode: Suitable for daily cleaning of soft textiles like plush toys and quilts.
• Intelligent Mode: Adapts suction power automatically based on mite density for various cleaning scenarios. Higher mite density results in stronger suction.
• High Suction Mode: Suitable for deep cleaning of hard textiles like mattresses and sofas.

Care and Maintenance

General Warning: Always switch off and unplug the mite vacuum cleaner before cleaning or maintenance.

Dustbin Cleaning

Regularly clean the dustbin to prevent dust accumulation, which can lead to blockages and reduced suction power. It is recommended to open the dustbin over a trash can to prevent dust from falling onto the floor. Do not immerse the mite vacuum cleaner in water during cleaning.

Daily Dustbin Cleaning

1. Press the dustbin release button and pull out the dustbin assembly.
2. Empty the dustbin over a trash can, aligning the marking 'o' with the symbol '6'. Open the dustbin assembly upside down, empty the dustbin, and clean the surface of the dustbin cover assembly.
3. After emptying, align the marking 'o' on the dustbin with the symbol '6' to reattach the dustbin cover assembly to the dustbin. Then, twist the dustbin until the marking 'o' aligns with the symbol '8'. You should hear a "click" when it is securely locked.
4. Check if the baffle plate of the dustbin assembly is installed correctly. Then, reinsert the dustbin assembly into the main unit.

Washing the Dustbin Assembly

When suction power decreases, clean the dustbin assembly promptly to restore mite removal performance and prevent air duct blockage.

1. Remove the dustbin cover and twist it to remove the cyclone separator.
2. Remove the filter holder assembly from the dustbin cover, then remove the filter and filter wadding sequentially.
3. Clean the surfaces of the dustbin, dustbin cover, cyclone separator, filter holder, filter, and filter wadding. Rinse with clean tap water and allow them to air dry thoroughly.

Notes:

• It is recommended to wash and clean the filter every 5 to 6 uses, or more frequently as needed.
• It is recommended to replace the filter every 2-3 months to ensure optimal suction power.
• Ensure all parts are thoroughly air-dried (away from direct sunlight) after rinsing before reinstallation.

4. Reinsert the filter wadding and filter into the filter holder and press them into place. Then, place the filter holder assembly into the dustbin cover and press it into position.
5. Align the symbol '8' on the cyclone separator with the marking 'o' on the dustbin cover. Then, twist the cyclone separator until the marking 'o' aligns with the symbol '8'. You should hear a "click" when it is securely locked.
6. Securely lock the dustbin and the dustbin cover assembly, and then reinsert the dustbin assembly into the mite vacuum cleaner.

Roller Brush Cleaning

1. Activate the roller brush release button as indicated on the mite vacuum cleaner; the roller brush cover will automatically pop open. Remove the roller brush cover.
2. Remove the roller brush by pulling it upwards from the right side. Remove any hair and debris from the roller brush. Note: It is recommended to clean the roller brush at least once a month. Rinsing is not recommended.
3. Reinstall the roller brush after cleaning. Align the clips on the roller brush cover with the corresponding slots to reattach it, and push it down until you hear a "click".

Cleaning the Inlet and Mite Sensors

Remove the dustbin assembly to access the mite sensors in the inlet. Clean them with a dry cloth or towel.

Notes:

• It is normal for dust and other particles to accumulate in the inlet. Clean it promptly.
• If the mite sensors are dirty, the dust mite density indicator light will blink orange. Clean the mite sensors immediately. Regular cleaning of the sensors helps prevent dust accumulation and ensures detection accuracy.
• The air inlet filter wadding serves as a filter; do not discard it. If the filter wadding becomes dirty, remove and rinse it with clean tap water. Ensure it is thoroughly air-dried (away from direct sunlight) before reinstallation.

Troubleshooting

Notes:

• If a malfunction occurs during use, switch off the mite vacuum cleaner and disconnect it from the power supply before troubleshooting.
• If the problem persists after following the above steps, please contact the customer service team.

Specifications

Regulatory Compliance Information

Disposal of Electrical and Electronic Equipment

The symbol on the product or packaging indicates that the product must be collected separately for electrical and electronic equipment and should not be disposed of with normal household waste. Please remove batteries and lamps not enclosed by the device before disposal and hand them over to official collection points for batteries and lamps.

By correctly disposing of the product, you help to avoid negative impacts on the environment and human health that could arise from improper collection and treatment of waste electrical and electronic equipment.

For more information, please contact your local administration, your local waste disposal service, or the store where you purchased the product.

EU Declaration of Conformity

We, Guangdong Deerma Technology Co., Ltd., hereby declare that this device complies with applicable regulations and European standards, including any amendments. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html

A detailed electronic user manual can be found at www.mi.com/global/service/userguide