La Crosse Technology Wall or Table Digital Clock

Power Up

1. Insert 3-AAA alkaline batteries into your Clock.
2. Configure your basic settings.

Diagram showing the back of the clock with battery compartment and buttons labeled SET, MODE, ALARM, and +/-.

Settings Menu

To enter the Settings Menu, hold the SET button until the display changes.

1. Press and release the + or - button to adjust values.
2. Press and release the SET button to confirm and move to the next item.
3. Press and release the SNOOZE/MODE button at any time to exit.

Settings order:

• Hour
• Minutes
• Year
• Month
• Date

The weekday will set automatically when the Year, Month, and Date are set.

Custom Display

Press and release the SNOOZE/MODE button to select between Calendar or Seconds Display.

Diagram showing two clock displays: one in Calendar mode showing time, day, month, and date; the other in Seconds mode showing time and seconds.

Time Alarm Settings

1. Hold the ALARM button until the display changes to enter the Alarm Settings. “AL” will show in the lower right corner.
2. Press and release the + or - button to adjust values.
3. Press and release the ALARM button to confirm and move to the next item.
4. Press and release the SNOOZE/MODE button at any time to exit.

Settings order:

• Hour
• Minutes

Diagram showing alarm time setting for 6:00 AM.

Diagram showing alarm time setting for 6:30 AM.

Activate/Deactivate Alarm

• The alarm is active when set.
• Press and release the ALARM button to deactivate or activate the alarm. The alarm time will show briefly.
• The Alarm Icon ? is displayed when the alarm is active.

Diagram showing an active alarm with the alarm icon displayed.

Diagram showing an inactive alarm.

Snooze

• When the alarm sounds, press and release the SNOOZE/MODE button to silence the alarm for 10 minutes. The Snooze Icon ? will flash.
• Press and release any button except SNOOZE/MODE to silence the alarm for 24 hours.
• If no buttons are pressed, the alarm sound will turn off automatically after 2 minutes.

Diagram showing the clock display with the snooze icon flashing.

Low Battery Icon

When the Low Battery Icon ? shows, replace the batteries.

Specifications

• Power: 3 “AAA” (LR3, IEC) Alkaline Batteries (not included)
• Battery Life: 24 + months
• Dimensions: 7.13" L x 0.83" W x 4.88” H (18.11cm L x 2.11cm W x 12.40cm H)

Diagram showing the front, side, and back views of the clock with dimensions labeled in inches and centimeters. The back view shows the battery compartment and button layout.

Stay in Touch!

Ask questions, watch set up videos, and provide feedback on social media outlets. Follow La Crosse Technology on YouTube, Facebook, Instagram, and X (Twitter).

YouTube Facebook Instagram X (Twitter)

Warranty & Patents

La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to manufacturing defects in materials & workmanship. In accordance with the Song-Beverly Act, in the state of California, the warranty on this item becomes effective on the date of delivery.

La Crosse Technology, Ltd, 2830 S. 26th St., La Crosse, WI 54601
Phone: 608.782.1610

For Full Warranty Details, Visit: www.lacrossetechnology.com/pages/warranty
Patents: www.lacrossetechnology.com/pages/patents

We're Here to Help

If you require additional assistance, get in touch with our friendly customer support team based in La Crosse, WI.

Self-Help: bit.ly/w72258_support

Online: bit.ly/contact_techsupport

Phone: 1.608.782.1610

Our knowledgeable team is available: Mon-Fri 8am-6pm CST

Diagram showing a QR code for additional info and support.

WARNING This product can expose you to chemicals including acrylonitrile, 1, 3-butadiene, and styrene, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov

Care & Maintenance

• When batteries of different brand or type are used together, or new and old batteries are used together, some batteries may be over-discharged due to a difference of voltage or capacity. This can result in venting, leakage, and rupture and may cause personal injury.
• Do not mix Alkaline, Lithium, standard, or rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for the intended use.
• Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of different types.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries are installed correctly with regard to polarity (+ and -).
• Remove batteries from product during periods of non-use. Battery leakage can cause corrosion and damage to this product.
• Remove used batteries promptly.
• For recycling and disposal of batteries, and to protect the environment, please check the internet or your local phone directory for local recycling centers and/or follow local government regulations.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or processed using electronic, mechanical or chemical process without the written permission of the publisher. This booklet may contain errors or misprints. The information it contains is regularly checked and corrections are included in subsequent editions. La Crosse Technology disclaims any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized. La Crosse Technology is not responsible for any radio or TV interference caused by unauthorized changes or modifications to this equipment. Such changes or modifications could void the user authority to operate the equipment.