Installation Instructions
STAR & ART BLACK ECOLINE DOUCHECABINE SLIDE DOOR
Available Sizes: 80x80x190CM, 90x90x190CM
Tools Required (Not Supplied)
Before starting, ensure you have the following tools, ample space, and a clean, dry area for assembly. Two people are recommended for installation. While these instructions are comprehensive, it is advisable to have a technically competent installer perform the assembly.
- [drill bit] to suit wall type (5.5mm)
- [power drill]
- [silicone sealant gun]
- [scissors]
- [tape measure]
- [rubber mallet]
- [pencil]
- [magnetic cross head screwdriver]
- [spirit level]
Parts List
| No. | Name | PCS | No. | Name | PCS |
|---|---|---|---|---|---|
| A | Wall profile | 2 | A1 | 6mm wall plug | 11 |
| B | Fixed glass | 2 | B1 | 4x25mm screw | 8 |
| C | Sliding glass | 2 | C1 | 4x25mm flat head screw | 2 |
| D | Rubber seal | 4 | D1 | 4x30mm flat head screw | 3 |
| E | Magnetic rubber seal | 2 | E1 | Bottom corner | 1 |
| F | Aluminum alloy rail cover strip | 2 | F1 | Sliding block | 2 |
| G | Top rail | 2 | G1 | Cover cap | 2 |
| H | Bottom rail | 2 | H1 | Top corner | 1 |
| I | Bottom rubber seal | 2 | I1 | Handle | 2 |
| J | Strips | 1 | J1 | Roller | 4 |
| K | Aluminum alloy rail cover strip | 2 | K1 | 4x14mm flat head screw | 2 |
| L | Strap | 1 | L1 | 4x10mm screw | 8 |
| M1 | 3mm Drill Bit | 1 | |||
| N1 | Position block | 4 | |||
| O1 | 2.5mm Allen key | 1 | |||
| P1 | 3mm Allen key | 1 |
Installation Steps
STEP 1: Prepare Wall Profiles
This step involves attaching the wall profiles (A) to the wall. Measure and mark the desired positions, ensuring the correct spacing (78-79cm or 88-89cm). Drill holes using a 5.5mm drill bit and insert 6mm wall plugs (A1). Secure the wall profiles (A) using 4x25mm screws (B1).
Visual description: Two wall profiles are shown being attached vertically to corners of a room. Close-ups illustrate drilling holes, inserting wall plugs (A1), and screwing the profiles (A) to the wall using screws (B1).
STEP 2: Attach Bottom Rail and Straps
Attach the bottom rail (H) to the wall profiles (A). Insert the strips (J) into the bottom rail. Secure the bottom rail using straps (L) and attach the top rail (G) to the wall profiles.
Visual description: The bottom rail (H) is positioned. A close-up shows inserting a strip (J) into the rail. Another close-up shows a strap (L) being attached. The top rail (G) is then shown being attached to the wall profiles (A).
STEP 3: Install Fixed Glass Panels
Slide the fixed glass panels (B) into the wall profiles (A). Ensure they are seated correctly in the bottom rail (H).
Visual description: Two fixed glass panels (B) are shown being slid downwards into the vertical wall profiles (A).
STEP 4: Attach Top Corner and Rollers
Attach the top corner piece (H1) and position blocks (N1) to the top rail (G). Install rollers (J1) onto the sliding glass panels (C) using position blocks (N1) and screws. Attach the aluminum alloy rail cover strip (K) to the bottom rail (H) and the top rail (G).
Visual description: Close-ups show attaching the top corner piece (H1), position blocks (N1), rollers (J1) to the sliding glass panels (C), and the rail cover strips (K) to the top (G) and bottom (H) rails.
STEP 5: Install Sliding Blocks and Bottom Rail Components
Attach sliding blocks (F1) to the top rail (G). Secure the bottom rail (H) components. Insert the bottom rail cover strip (F) and attach the bottom corner piece (E1). Use 4x30mm screws (D1) and 6mm wall plugs (A1) as needed.
Visual description: Close-ups show attaching sliding blocks (F1), bottom rail (H) components, rail cover strips (F), and bottom corner pieces (E1). Screws (D1) and wall plugs (A1) are indicated for securing.
STEP 6: Attach Magnetic Seals and Bottom Corners
Attach the magnetic rubber seals (E) to the glass panels. Secure the bottom corner pieces (E1) to the bottom rail. Use a 5.5mm drill bit and 4x30mm screws (D1) with wall plugs (A1) for securing.
Visual description: Close-ups show attaching magnetic seals (E) to glass edges and bottom corner pieces (E1) to the bottom rail (H). Drilling and screwing actions are depicted using a 5.5mm drill bit and screws (D1) with wall plugs (A1).
STEP 7: Prepare Sliding Glass Panels
Attach the rubber seals (D) to the edges of the sliding glass panels (C). Ensure the seals are properly fitted.
Visual description: Two sliding glass panels (C) are shown. Close-ups illustrate attaching rubber seals (D) along the edges of the glass panels.
STEP 8: Install Sliding Glass Doors
Carefully slide the prepared sliding glass doors (C) onto the top rail (G) and into the bottom rail (H). Ensure the rollers (J1) engage correctly with the tracks.
Visual description: The sliding glass doors (C) are shown being lowered into place, engaging with the top rail (G) and bottom rail (H), with rollers (J1) visible.
STEP 9: Attach Handles
Attach the handles (I1) to the sliding glass doors (C) using the provided screws.
Visual description: Close-ups show the handles (I1) being attached to the pre-drilled holes on the sliding glass doors (C).
STEP 10: Secure Bottom Rail and Top Rail
Secure the bottom rail (H) and top rail (G) using 4x10mm screws (L1). Ensure all connections are firm.
Visual description: Close-ups show screws (L1) being used to secure the bottom rail (H) and top rail (G).
STEP 11: Attach Rail Cover Strips and Caps
Attach the aluminum alloy rail cover strips (F) to the top rail (G). Fit the cover caps (G1) and secure with 4x25mm flat head screws (C1).
Visual description: Close-ups show attaching aluminum alloy rail cover strips (F) to the top rail (G), fitting cover caps (G1), and securing them with screws (C1).
STEP 12: Final Sealing and Curing
Apply silicone sealant around the base of the shower cabin and where the profiles meet the wall. Allow [24 hours curing time] before use.
Visual description: The shower cabin is shown with silicone sealant being applied at the base and edges. An icon indicates a 24-hour waiting period before use.
