Vention Wireless HDMI Video Transmitter and Receiver User Manual | VWS-102
Document Revision: 2025/07/08 | Initial Release | Revision A
Product Overview & Specifications
Product Overview
Transmitter-TX
Diagrams show the Vention Transmitter-TX device from multiple angles (front, back, top, bottom, sides). Icons indicate connection ports: HDMI IN, USB-C (for power/data), and a button. A schematic illustrates its connection to a display device.
Receiver-RX
Diagrams show the Vention Receiver-RX device from multiple angles. Icons indicate connection ports: HDMI OUT, USB-C (for power), and a button. A schematic illustrates its connection to a display device.
Specifications
| Model | ADU |
| Interface | TX: HDMI-IN/HDMI-OUT/USB-C RX: HDMI/USB-C |
| Electroplating Process | Nickel-Plated |
| Material | ABS |
| Resolution | TX: 1080P@60Hz (HDMI-OUT) RX: 1080P@60Hz (Wireless Transmission) Multi-Screen Mirroring: 1080P@60Hz (HDMI-OUT/Wireless) |
| Rated Input | TX: 5V-2A RX: 5V-2A |
| Wireless Frequency | 5.8GHz |
| Effective Range | 200M Max |
| Battery | NP-F750F 7.4V (Not Included) |
Note:
- This product is designed to be used with a USB-C power adapter or an NP-F750F7.4 battery.
- The USB-C power adapter connection cannot charge the NP-F750F7.4 battery.
- The NP-F750F7.4 battery must be charged using its dedicated charging dock.
What's in the Box
- Wireless HDMI Video Transmitter x1 + Receiver x1
- USB-C Charging Cable x 2
- Cold Shoe x 1
- User Manual x 1
Screen Mirroring
Plug and Play
Transmitter-TX
Diagram shows the Transmitter-TX device connected to a source device (e.g., laptop) via HDMI and USB-C.
Receiver-RX
Diagram shows the Receiver-RX device connected to a display device (e.g., TV) via HDMI.
Basic Functions
- Connect the HDMI source to the transmitter (TX), and connect the receiver (RX) HDMI to a display device (e.g., TV, monitor, projector, etc.).
- Power on both the transmitter (TX) and receiver (RX). When the indicator lights turn on ?, the system is operating normally.
- Press and hold the TX button ? for 5 seconds to activate Pairing Mode. Briefly press the button ? to cycle through available channels.
Pairing & Connection
- Use an HDMI cable ? to connect the receiver (RX) HDMI-OUT to the transmitter (TX) HDMI-IN.
- Once successfully paired ✔️, the screen will display "Connected".
- (Ensure the battery is properly installed and has sufficient power during pairing.)
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
FCC ID: 2A7Z4-ADU
Manufacturer Information
Company: Ningbo Fulman Communication Technology Co., Ltd.
| Part Name | ADU Series HDMI Transmitter and Receiver User Manual |
| Part Model | VWS-102 |
| Designer | Muzi |
| Unit | mm |
| Client NO. | |
| Rev | A2 |
| DWG.NO. | |
| Page | 1/1 |
| Update | 2025/07/08 |
Printing Details:
- Product Size: 70x90mm
- Material: 80g matte paper, 3 pages, accordion fold, double-sided printing
- Blue Printing: C100 M:0 Y:0 K:0
- Reference: Pantone Process Cyan C
Connect With Us
For more interesting information and events, please follow us on social media platforms:
For warranty service or support, please contact the Vention team:
Website: www.ventiontech.com
Email: vention@ventiontech.com
