iGAGING Electronic Digital Indicator Operating Instructions and Parts Manual
Please read through this owner's manual carefully before using your new tool. Use your tools properly and only for its intended use.
I. Features
- 1. ON/OFF
- 2. ZERO setting
- 3. Absolute/Incremental readings
- 4. mm/in conversion
- 5. Tolerance
- 6. Battery cover
- 7. Lug back and 3/8 stem diameter
- 8. 4-48 contact point
- 9. Data Output Port
II. Operation
Press ON/OFF (1) to turn unit on or off.
Set ZERO at any location press ZERO (2). This can be used in either ABS or INC.
Press mm/in (4) to display readings in either inch or metric.
Press ABS/INC (3) to toggle between Absolute and Incremental (INC) reading. A relative ZERO may be set at any location in INC mode.
Tolerance indicators may be activated by pressing TOL (5) one time. "[up-arrow]" will appear in the display. Displace the spindle so the maximum allowed reading is displayed and press TOL once more "[down-arrow]" will appear in the display. Displace the spindle so the minimum allowed reading is displayed and press TOL once more. "OK" will be shown in the display while the readings are between the two allowed readings. Once either of these settings has been exceeded, "OK" will flash indicating an out of tolerance measurement. To exit TOL mode depress ZERO (2).
To reset tolerances, depress TOL (5) and input the maximum and minimum readings.
Battery: When display is fading, flash, or no display, please change battery. 3V CR2032 1 piece.
Please recycle responsibly.
Specifications
| Item# | Range | Reading | Accuarcy | Repeatability | Anvil |
|---|---|---|---|---|---|
| 35-125-A | 0-1" / 0-25mm | 0.0005”/0.01mm | 0.001" | 0.0005”/0.01mm | Ball tip |
| 35-125-4 | 0-1" / 0-25mm | 0.0005”/0.01mm/128th | 0.001" | 0.0005”/0.01mm | Ball, point, flat, spline |
| 35-126 | 0-0.5" / 0-12.7mm | 0.0005”/0.01mm | 0.001" | 0.0005”/0.01mm | Ball tip |
| 35-128 | 0-1" / 0-25mm | 0.0005”/0.01mm/128th | 0.001" | 0.0005”/0.01mm | Ball tip |
Data Output (Optional)
This section describes the optional data output feature, which allows the digital indicator to connect to a computer for data collection.
Instructions:
- Insert USB plug into a computer with a USB port and a Windows operating system. The computer will automatically install the software included in the kit. (In some cases, manual installation may be required).
- Insert the Micro USB plug into the iGAGING digital indicator (#35-125-A, 35-125-4, 35-126, or 35-128) data port. Observe the proper polarity.
- Open a Windows-based data collection program (e.g., Excel) and place the mouse cursor on a data field of the desired location.
- Important: Set zero on both the indicator and the data kit simultaneously after plug-in and before making a measurement.
- Press DATA on the data kit to export measurement data.
- Use the in/mm key to switch data output unit. Inch fractional cannot output.
- Repeat the set zero process if output data is off.
Important Notes & Care
- Do not disassemble the instrument.
- Do not subject the instrument to blows or shock.
- Do not store the instrument under direct sunlight.
- Avoid exposing the unit to strong magnetic fields and live voltage.
- Use a soft cloth to clean the instrument before and after usage.
- Never use organic solvents such as acetone or benzene to clean.
Please check with iGAGING for the most updated product information. Manufacture supplied information. Information may change without notice.
© iGAGING 2016
Enjoy Accuracy®
