DESCRIPTION
One Ceiling Fan and Light, 3 Speed, Reversing, Demo Remote Control
FAN MODEL USED: See Catalog or visit our website www.fanimation.com for more information
How to Wire and Operate Your TR28 Transmitter
NOTE: If fan or supply wires are different colors than indicated, have this unit installed by a qualified electrician.
⚠️ WARNING
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation.
1. Setting the Code
The remote unit has 16 different code combinations. It may be necessary to test a couple frequency code settings to improve signal reception and/or eliminate interference from other remote control household items. Multiple fans should have different code settings to allow independent fan control. To set the code, perform these steps.
2. Transmitter
Remove battery cover. Press firmly below the arrow and slide the battery cover off. Slide code switches to your choice of up or down position. The factory setting is all up. Do not use this position. With a small screwdriver or ball point pen, slide firmly up or down (See Figure 1a description).
Remote Transmitter Unit Detail: Shows a 3V CR2032 battery compartment and four DIP switches labeled 1, 2, 3, 4 for code setting.Replace battery cover on the transmitter.
3. Receiver
Slide code switches to the same positions as set on your transmitter (See Figure 1b description).
Receiver Unit Detail: Shows four DIP switches labeled 1, 2, 3, 4 for code setting and an ON/OFF switch.4. Operating & Using Remote Transmitter
Install two 3-volt batteries (If not using for long periods of time, remove batteries to prevent damage to the transmitter). Store the transmitter away from excess heat or humidity.
- HI Push Button – high fan speed
- MED Push Button – medium fan speed
- LOW Push Button – low fan speed
- [Fan Off] Push Button – fan off
- REV Push Button – toggles between air upflow and air downflow
- *Demo Push Button – on/off auto demo mode
- Light Push Button – on/off and brightness control for optional down light.
NOTE:
- To control the light, hold down the key to increase or decrease brightness. Tap the key quickly to turn the light on or off. The light keys have auto-resume and will stay at the same brightness as the last time it was turned off.
- Demo mode is initiated by pressing the Demo button on the remote; the lights will flash 3 times. The fan runs for 2.5 minutes then shuts off for 1.5 minutes. These 2.5 / 1.5 minute run cycles continue until any other button is pressed on the remote control.
How to Install Your Remote Control
The following options detail how to install the control bracket.
Option #1
1. Unthread two screws from the wall switch plate (See Figure 1 for Option #1).
2. Install the control bracket with two #6-32x 3/4" screws. Push the four plastic plugs to cover the screw holes (Included with the control) (See Figure 2 for Option #1).
Installation Option #1: Figure 1 shows a wall switch plate with screws removed. Figure 2 shows the control bracket attached with #6-32x 3/4" screws and plastic plugs.Option #2
1. Unthread two screws from the wall switch plate (See Figure 1 for Option #2).
2. Install the control bracket with two #6-32x 1" screws. Push the four plastic plugs to cover the screw holes (Included with the control) (See Figure 2 for Option #2).
Installation Option #2: Figure 1 shows a wall switch plate with screws removed. Figure 2 shows the control bracket attached with #6-32x 1" screws and plastic plugs.Option #3
1. Drill two 1/4" holes in the wall and use the M6 plastic anchors pushed into the holes. Install the control bracket with two #3- 1" self-tap screws. Push the four plastic plugs to cover the screw holes (Included with the control) (See Figure 1 for Option #3).
Installation Option #3: Figure 1 shows drilling holes in the wall, inserting M6 anchors, and attaching the control bracket with #3- 1" self-tap screws and plastic plugs.
