ThermPro TP-30 Digital Laser Infrared Thermometer Instruction Manual

Introduction

Thank you for purchasing the ThermoPro TP30 Infrared Thermometer. This easy-to-use device lets you conveniently and accurately measure surface temperatures from a distance without the need for direct contact.

Features & Specifications

• Laser guided targeting for better aiming precision
• Narrow distance-spot ratio for accurate results at long distances
• Safely measure hazardous or inaccessible objects
• Battery: 2*AAA batteries, 3.0V
• Measurement Range: -58°F~1022°F (-50°C~550°C)
• Accuracy: ±1.5%
• Resolution: 0.1°F or 0.1°C
• Wavelength: 5um-14um
• Distance-Spot Ratio: 12: 1
• Response Time: 500ms
• Emissivity: 0.10-1.00 (Default 0.95)
• Backlight: Auto-off after 15 seconds
• Auto-off: Auto-off after 90 seconds of inactivity
• Low battery Indicator ?

Function Diagram

The device features a digital display and several control buttons. The main components are:

• 1. SCAN: Indicator displayed when pressing the measurement trigger.
• 2. HOLD: Indicator displayed when the measurement trigger is released.
• 3. Laser Pointer Indication: A laser beam appears when the measurement trigger is pressed to aid aiming, unless the laser is turned off.
• 4. ? Low Battery Indication: Appears on the display when battery power is low.
• 5. UPPER DISPLAY: Shows the latest temperature measurement.
• 6. EMISS: Indicator for emissivity setting.
• 7. LOWER DISPLAY: Shows MAX/MIN/AVG temperature.
• 8. MAX/MIN: Displays the maximum and minimum temperature recorded for the latest measurement.
• 9. AVG: Displays the average temperature recorded for the latest measurement.
• 10. °C/°F / [Laser Toggle] / [Temp Unit Switch] / [Emissivity Down]: Buttons for controlling laser pointer, switching between Celsius (°C) and Fahrenheit (°F), and decreasing emissivity. Press once to turn laser on/off. Press and hold for 3 seconds to switch temperature units. When adjusting emissivity, press to lower it.
• 11. MODE: Button to cycle through MAX/MIN/AVG temperature displays. Press and hold for 3 seconds to adjust emissivity setting.
• 12. ▲ / [Backlight Toggle] / [Emissivity Up]: Buttons for controlling backlight and emissivity. Press to turn backlight on/off. When adjusting emissivity, press to increase it.
• 13. [Laser Aperture]: The opening for the laser beam.
• 14. [IR Sensor]: The infrared sensor that detects surface temperature.
• 15. Measurement Trigger: Hold to take readings, release to lock the result.
• 16. [Battery Compartment]: Located at the base of the handle, for inserting batteries.

The device is a handheld unit with a display screen, trigger, and control buttons. It includes an IR sensor and a laser aperture for targeting.

Operation: Surface Temperature Measurement

NOTE: The ThermoPro TP30 cannot measure the temperature of objects behind glass. Inaccuracy may also occur when exposed to steam, dust, or other contaminants in the air.

1. Place the included AAA batteries into the Battery Compartment, then press the Measurement Trigger to activate the thermometer.
2. Point the TP30 thermometer towards the surface you wish to measure.
3. Press and hold the Measurement Trigger; the laser will activate for aiming guidance (Laser appears if enabled, on by default).
4. Keep holding the Measurement Trigger as you move the TP30 to continually take measurements of the surface.
5. Once the laser is pointed to the desired measurement point, release the Measurement Trigger. The Upper Display will show the last measured temperature.
6. Press the Measurement Trigger again to make another measurement.

Diagrams show the trigger being held for continuous reading and released to lock the temperature result.

Emissivity

The emissivity of a material is its efficiency in emitting thermal energy. Non-reflective surfaces have a higher emissivity (closer to 1) than reflective surfaces (closer to 0). Inaccurate results may occur when measuring reflective surfaces such as glass, polished wood, and granite.

To take accurate temperature measurements of reflective surfaces with low emissivity, place a strip of masking tape over the surface and allow it to adjust to the surface temperature for approximately 30 minutes. Measure the surface, scanning the taped section, to eliminate measurement inaccuracy.

The default emissivity of this device is 0.95, which is suitable for surface temperature measurement of most organic materials and painted objects. You can refer to the emissivity tables below to improve measurement accuracy for different objects.

Emissivity Table 1

Emissivity Table 2

Distance-Spot Ratio

The ThermoPro TP30 measures surface temperature based on the distance to spot diameter ratio (D: S). As the distance between the thermometer and the surface increases, the total surface area measured will also increase. With a distance to spot ratio of 12:1, the surface area measured has a diameter of roughly 1/12 the distance.

For the most accurate results, ensure the target has a surface area of at least twice the corresponding spot diameter. Insufficient surface area will result in inaccurate readings. The recommended distance to hold the thermometer from the surface is 7.87 inches (20cm), which creates a spot measurement area of 0.66 inches (1.67cm) in diameter.

Diagram illustrates the D:S=12:1 ratio, showing spot diameters of approximately 0.79in (2cm) at 9.45in (24cm) distance and 1.18in (3cm) at 14.17in (36cm) distance.

Replacing Batteries

The Low Battery Indication ? will appear on the Upper Display when the thermometer's batteries are running low. Immediately replace the batteries when the icon appears.

1. Open the Battery Compartment and remove the used batteries. Dispose of them properly.
2. Insert two new AAA batteries with the correct polarity.
3. Close the Battery Compartment.

Package Contents

• 1x ThermoPro TP30 Infrared Thermometer
• 2x AAA batteries
• 1x User Manual

Safe Use & Care

• DO NOT point the laser beam at another person or animal.
• DO NOT attempt to point the laser beam at an aircraft.
• Avoid direct/indirect eye contact with the laser beam. Laser radiation may cause eye damage.
• DO NOT view the beam with optical instruments.
• If using near bystanders, make them aware of the dangers of looking directly into the laser beam.
• DO NOT allow children to operate the device.
• Use two 1.5V AAA batteries when replacing batteries.
• Ensure batteries are inserted with correct polarities.
• ALWAYS remove batteries when cleaning the device.
• DO NOT use leaking batteries or dispose of old batteries in fire.
• Remove batteries if storing the device for a prolonged period.
• DO NOT disassemble the device or tamper with internal components, as this will void the warranty.
• DO NOT touch the lens or wipe it using anything other than a soft cloth or cotton swab.
• Keep the thermometer away from electromagnetic fields produced by objects such as arc welders and induction heaters.
• DO NOT expose the thermometer to direct sources of heat for extended periods.
• The thermometer measures surface temperature, not internal temperature. Do not use it as a reliable source to measure body temperatures.

Disposal

Meaning of the "Dustbin" Symbol ?️:

• Protect our environment: do not dispose of electrical equipment in domestic waste.
• Please return any electrical equipment you no longer use to the collection points provided for disposal.
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reutilisation of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.

CAUTION: ⚠️ Batteries/rechargeable batteries must not be disposed of with household waste!

• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.

Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/rechargeable batteries which contain hazardous substances:

• ⚠️ Pb = contains lead
• ⚠️ Cd = contains cadmium
• ⚠️ Hg = contains mercury
• ⚠️ Li = contains lithium

Limited One-Year Warranty

ThermoPro warrants this product to be free of defects in parts, materials, and workmanship for a period of one year from the date of purchase. Should any repairs or servicing under this warranty be required, contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Customer Service

Telephone:

• 1-877-515-7797 (USA & Canada only)
• 44-203-769-1321 (UK)

Email: service@buythermopro.com

Hours:

• Weekdays 8:00 AM - 8:00 PM EST (USA & Canada only)
• Weekdays 1:00 PM - 12:00 AM CET (UK)