Lumene EDEN Extra Bright UST / LT User Manual and Installation Guide

Introduction

Thank you for choosing Lumene products. Please read this manual carefully before installation and use. Keep it for future reference.

Important Safety Precautions:

• Please tear out all the blue tape from the trap door before powering on.
• Do not reach into the casing gap to prevent hand injury when the screen goes up.
• Please position the screen in a location without wind to prevent it from falling over.
• Do not dismantle or replace original spare parts without consulting Lumene.
• If you encounter any problems, please contact the after-sales service.
• Any functional or structural adjustments will not be further notified and are subject to practical product application.

Parts List

The following parts are included with your Lumene EDEN screen:

• 1x Power cable
• 1x USB to 2.5mm jack cable
• 2x Adjustable Mounting Bracket (optional)
• 1x Adjustment key (4mm)
• 1x Allen Key
• 6x M5 nylon nut
• 1x Socket wrench
• 1x Brush
• 1x User manual
• 1x Wireless remote

Note: Batteries are not provided. The remote control requires 2 x CR2032 button cell batteries.

For assistance with assembly, visit the FAQ page at www.lumene-screens.com/f-a-q for additional instructions and videos.

Screen Structure Diagram

The projection screen consists of the following main components:

• Fabric (Toile): The projection surface.
• Door (Porte): The decorative front panel that opens and closes.
• Casing (Caisson): The housing for the screen mechanism.
• Fabric support bar (Barre de support de la toile): The bar at the bottom of the fabric.
• Upper support arm (Bras de support supérieur): The arm supporting the top of the fabric.
• Joint (Joint): Connectors for the arms.
• Lower support arm (Bras de support inférieur): The arm supporting the bottom of the fabric.

Installation Guidelines

Mounting Bracket Installation

Slide the mounting brackets into the two guides underneath the casing. Position them symmetrically to stabilize the screen.

The height of the feet can be adjusted to compensate for irregular ground.

Key Components for Installation:

• Side handle (Poignée latérale)
• Manual cycle button (Bouton de cycle manuel)
• Flexible door opening and closing device (Dispositif flexible d'ouverture et de fermeture des portes)
• IR jack (Ø 3.5)
• Power jack (Prise d'alimentation)
• 12V trigger jack (Ø 2.5)

Step-by-Step Installation

1. Positioning the Screen: Lay the projection screen flat on the cabinet. Leave at least 4mm of space from the wall for the door's operation.
2. Extending and Tilting: Fully extend the projection screen using the remote control. Adjust the tilt of the projection screen using the level adjustment knobs located under the casing.

   Caution: The projection screen might tip over if there is too much tilt.

3. Marking and Bracket Placement:
   1. Measure the total length of the casing. Measure the height where the bottom of the projection screen will be placed and mark it on the wall.
   2. Refer to the table for the recommended distance "A" between the two adjustable brackets.
   3. Align the top of the adjustable bracket with the bottom of the projection screen (the mark made on the wall).
4. Drilling and Securing Brackets:
   1. Drill 4 holes for each bracket on the wall and install an appropriate anchor in each hole.
   2. Place the adjustable brackets against the wall, aligning them with the anchors, and tighten using 5x40 tapping screws.
5. Attaching Screen to Brackets:
   1. Adjust the T-slot bolt on the adjustable bracket so it is parallel with the wall (refer to diagram).
   2. Place the projection screen onto the adjustable brackets.
   3. Adjust the projection screen horizontally to the desired position.
   4. Tighten the T-slot bolt from under the adjustable brackets to lock the screen in place.
   5. Note: T-slot bolts are installed for front installation by default. Users can install them in the reverse mounting holes for reversed installation if needed.
6. Final Connections and Adjustments:
   1. Connect the power cable.
   2. Fully extend the projection screen and observe its tilt.
   3. Adjust the tilt using the Allen key to the desired position to complete the installation.

Mounting Distance Chart

Diagram illustrating how to make a line at the bottom of the casing and a center line.

Screen Tilt Adjustment

Adjusting the tilt of the projection screen is done by turning the level adjustment knobs located under the casing.

Ensure a minimum distance of 4mm to the wall.

T-Slot Bolt Installation

The T-slot bolt is used to secure the screen to the mounting brackets. It can be installed for front installation or reversed installation.

The ±1.5° adjustment allows for fine-tuning the screen's angle.

Functions and Instructions

This product offers three control methods:

• A. Manual Cycle Button: Located on the end cover of the power supply side of the casing. Pressing this button cycles the screen through rising, stopping, falling, stopping, and rising repeatedly.
• B. 12V Trigger Control: Connect a 12V trigger cable to synchronize the screen's operation with your projector. The screen will automatically open when the projector turns on and close when it turns off.
• C. RF Remote Control:
  • Up Button: The decorative door opens first, then the fabric rises.
  • Stop Button: Pauses the movement of the door or fabric.
  • Down Button: The fabric rolls back into the casing, and the decorative door closes.
  • Jog Up/Down Keys: Allow manual up or down movement of the fabric.

  The remote control also supports intelligent electronic itinerary positioning, allowing you to set custom screen unfolding positions.

  Operation Method for Itinerary Positioning:

  1. Insert a paperclip into the positioning setting hole on the back of the remote.
  2. Press the positioning setting key (light will turn on).
  3. Use the remote's up and down buttons to move the screen to the desired position.
  4. Press the stop button.
  5. Press the positioning setting key again (light will turn off). The location is now recorded successfully.

Control Component Identification:

• Manual Cycle Button: Used for manual screen operation.
• IR Jack (Ø 3.5): For infrared remote control input.
• 12V Trigger Jack: For connecting to a projector's trigger output.
• Projector: The connected projector.

Door Anti-Pinch Function

The screen features a flexible door opening and closing device designed to protect hands or objects from accidental pinching when the door closes.

Abnormal Situation: If the elastic protection device is triggered during door closure, the tension spring may stretch. This can alter the door's opening/closing angle and prevent proper resetting.

Solution: Remove the two ø4 x 8 self-tapping screws connecting the door. Turn the tension spring counter-clockwise until it rebounds correctly. Restore the parts to their original state.

Visual States:

• Initial State: The normal operating condition of the door mechanism.
• Abnormal State: Shows the door mechanism after the anti-pinch function has been triggered, potentially with a stretched spring.

Components:

• Flexible door opening and closing device

Fabric Cleaning

Cleaning Ultra-Short Throw Anti-Light Screens:

• Do not use a rag to wipe the screen.
• Use a soft brush (included in the parts box) and lightly brush horizontally along the screen's texture to remove dust or fine particles.
• Light-colored smudges that do not affect projection do not require cleaning. If they impact viewing, they can be removed with a residue-free adhesive tape.

Cleaning Ordinary Projection Fabric:

• Use clean water or a mild detergent to gently wipe stains on the fabric surface. Avoid corrosive detergents.
• Retract the fabric after air-drying or absorbing moisture.

General Precautions:

• Do not hang or place anything on the screen when it is unrolled.
• Do not put your fingers inside the casing when retracting the screen fabric.
• Dust and scratches reduce image quality. Avoid touching the screen surface with hands, drawing on it, or scratching it with sharp objects.
• Never use chemical cleaners on the screen surface.
• Ensure the screen is clear of obstructions before retracting.
• For dust removal, use a dry, soft-haired brush and rub gently.
• Always close the screen to protect the fabric.

Electrical Parameters

• Voltages and Frequencies: 110V/60Hz or 220V/50Hz (Actual voltage is indicated on the product's electrical label).
• Wireless Remote Control (F):
  • Voltage: 3V
  • Battery: 2 x CR2032 button cells
  • Transmitting Frequency: 868MHz
  • Effective Control Distance: Approximately 15 meters.
• Splicing Line: The screen may exhibit a slight curvature along the splicing line due to tension sources. This is a normal phenomenon and does not affect the projected image.
• Fabric Surface Flatness: The lower black drop range for perfect flatness is 300 - 400 mm.

Precautions for Use

Setting up your screen is straightforward but requires care to ensure its durability. Before first use, always position your screen horizontally on a stable surface.

Important Warnings:

• Do not place or hang anything on the screen case while the screen is unrolled.
• Keep fingers clear of the casing when retracting the screen fabric.
• Dust and scratches degrade projection quality. Pay close attention to the following:
  • a. Do not touch the screen surface with your hands.
  • b. Do not draw on the screen surface.
  • c. Do not scratch the screen with hard, sharp objects.
  • d. Never use chemical cleaners on the screen surface.
• Ensure nothing is on the screen before retracting it into the case.
• For dust removal, use a dry, soft-haired brush and rub gently.
• Close the screen to protect the fabric.

Visual Aids:

• Ambient Light: Illustrates how ambient light affects the projected image.
• Reflection Image Light: Shows how light reflects off the screen surface.
• Ultra Short Throw Projection Light: Depicts the light path from an ultra-short throw projector.

Warranty Information

Limited Warranty

All Lumene products carry a two-year limited warranty from the date of purchase when bought from Lumene, a Lumene distributor, or an authorized Lumene retailer. This warranty covers all defects in materials and workmanship in the product manufactured by Lumene.

Warranty Limitations and Exclusions

This warranty applies only to products purchased from Lumene or an authorized retailer/distributor and is valid for two years from the purchase date by the first end-user. It covers material and manufacturing defects, subject to the following exceptions:

• The serial number has been removed, modified, or made illegible.
• Defects or damage resulting from:
  • Improper operation, misuse, accident, or neglect (e.g., dropping, contact with water, sand, dirt, extreme heat, food, or liquids).
  • Physical damage to the product surface, including scratches or cracks.
  • Failure to follow instructions supplied with the product.
  • Damage incurred during shipment (claims must be addressed to the carrier).
  • Maintenance, alteration, modification, or servicing attempted by anyone other than Lumene or its authorized service centers.
  • Lack of user technical knowledge or experience unrelated to product defects.

Any of these conditions will void the warranty.

Eligibility for Limited Warranty Coverage

The limited warranty is valid only for the first end-user. To claim under this warranty, proof of purchase (sales receipt or invoice showing the purchase date) is required. The warranty is strictly limited to the country of original purchase.

Warranty-Related Expenses

Lumene covers all expenses for parts and labor for repairs or replacements under this warranty. Shipping and insurance fees are handled as described below.

Obtaining Warranty Service

If your product requires repair during the warranty period, please contact:

1. The original place of purchase.
2. Your local Lumene distributor.
3. Lumene directly, if the above are not identifiable.

Warranty service is limited to the country of original purchase. The local distributor will identify the nearest authorized service center. The product or suspected defective parts must be shipped, with freight, duties, and insurance prepaid, to the service center. Include:

• a) A copy of your dated invoice or proof of purchase.
• b) A written description of the problem.
• c) The name and location of the place of purchase.
• d) Your address and telephone number.

Always retain your original proof of purchase. Do not send products to a service center without prior agreement. Lumene or its authorized service center will ship a repaired or replacement product, with freight and insurance prepaid, if repairs are covered by the warranty.

Limitation of Liability

Except where national or other jurisdictional laws render these provisions inapplicable or unlawful, Lumene's sole liability for any defective product is to repair or replace it. Lumene shall not be liable for any damages exceeding the purchase price, nor for indirect, incidental, special, or consequential damages, including loss of revenue, profits, business, or other financial loss, arising from the use or inability to use the product, to the full extent permitted by law. Any disputes not resolved by preliminary conciliation regarding the interpretation or execution of this warranty will be settled definitively according to the rules of conciliation and arbitration of the International Chamber of Commerce of Paris, France, by one or more referees. French law applies.