Wireless Ergonomic Mouse

Product Contents:

• 1 x 6 Button Mouse
• 1 x USB-A 2.4Ghz Receiver
• 1 x USB-A to USB-C Charging Cable
• 1 x Instruction Manual

Product Overview

The front view of the mouse shows the standard layout with a right-click button, a left-click button, a scroll wheel with middle-click functionality, a forward button, a back button, and a DPI switch.

The bottom view reveals the USB-C input port for charging, a USB receiver storage slot, and an LED indicator. The LED indicator functions are labeled: Power Button, Up position for 2.4Ghz connection, Middle position for OFF, and Down position for Wireless Pairing.

*Product design may vary.

Connecting Your Mouse

Connecting via the Receiver:

• Remove the USB receiver from the back of the mouse and plug it into a USB-A port on your computer.
• Switch the power button on the mouse to the '2.4Ghz' position (up). The indicator light will flash red.
• The mouse and receiver will automatically pair. The indicator light will turn solid red when pairing is successful.

Connecting via Wireless Pairing:

• Switch the power button on the mouse to the 'Wireless Pairing' position (down). The indicator light will flash blue.
• On your device, search for and pair with 'PCEM-002'. The indicator light will turn solid blue, then fade once pairing is successful.

Adjusting DPI

• Press the DPI button to cycle through sensitivity settings: 800 DPI, 1200 DPI, and 1600 DPI.

Troubleshooting

• Mouse not connecting: Ensure the receiver is properly plugged into the computer. For wireless pairing, confirm it's enabled on your device and successfully paired.
• Mouse not responding: Check if the battery is low and recharge the mouse if necessary.
• Connection dropping: Move the mouse closer to the computer or reduce interference from other wireless devices.
• General device issues: Ensure your device is running the latest software updates. Check your device's settings for 'software update' options.

Safety Precautions

• Do not use the device near water sources.
• Do not modify or attempt to repair this device yourself.
• Do not clean the device with chemical detergents; use a soft, dry cloth.

Product Requirements

• A PC with a USB-A port.

Charging the Mouse

• A full charge takes approximately 3 hours.
• Connect the USB-C end of the charging cable to the mouse and the USB-A end to your computer.
• The LED indicator will show a solid red light while charging. It will turn off when charging is complete.

Note: The mouse can be used while it is charging.

Technical Specifications and Compliance

• Mouse Model: PCEM002
• FCC ID (Mouse): 2A023-PCEM001
• Mouse Input: 5V ⎓ 300mA
• Receiver Model: YZW1
• FCC ID (Receiver): 2A023-YZW1
• Working Distance: 8-10 meters

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Contact and Distribution

• Distributed by Chug, Inc.
• For support and repair information, contact the original manufacturer at customersupport@gemsfindyours.com
• Website: gemsfindyours.com
• Address: 7157 Shady Oak RD, Eden Prairie, MN 55344