Corsair VOID RGB ELITE Wireless Gaming Headset

Controls and Features

The headset features several controls and indicators:

• A Headband adjustment: Allows for adjusting the headband for a comfortable fit.
• B Power button: Turns the headset on or off.
• C Mute button: Mutes or unmutes the microphone.
• D RGB light: User-programmable RGB lighting.
• E Microphone foam windscreen (removable): Reduces wind noise and plosives.
• F Mic LED (mute): Indicates when the microphone is muted.
• G Status LED (RF, battery): Shows the status of the wireless connection and battery level.
• H Jog dial: Controls volume and EQ settings.
• I Charging port: Port for charging the headset.
• J Wireless sync LED indicator: Indicates the status of the wireless synchronization.
• K Pairing button: Used for pairing the wireless transmitter (pre-paired by default).

A diagram illustrates the location of these controls on the headset and the wireless transmitter.

Getting Started

To begin using the headset:

1. Connect the wireless USB transmitter to a USB port on your PC. The optimal wireless range is up to 40 feet (12m), but this can be affected by obstructions and other wireless devices.
2. The operating system will automatically install the device driver upon the first connection. It is recommended to reboot your PC after the driver installation.
3. Prolonged listening at high volumes can adversely affect hearing. Take breaks and start with the volume at the lowest level before increasing it.

Charging

The headset must be fully charged before first use.

• Connect the USB charging cable to a USB port on your PC.
• Connect the other end of the USB charging cable to the headset.
• The headset battery does not have a "memory effect," so it can be recharged without needing to be fully discharged first.
• Ensure the USB port used for charging is USB 2.0 or better, as some older USB ports may not support USB 2.0.

iCUE Software

Download the iCUE software from corsair.com/support/downloads to unlock the full feature set of your headset.

• Install the iCUE software on a PC running Windows 7, Windows 8.1, Windows 10, or later.
• Reboot your PC after installation and launch iCUE.

With iCUE software, you can:

• Customize RGB color and lighting intensity.
• Select and customize audio equalizer (EQ) settings.
• Adjust microphone input volume and sidetone.
• Enable or disable 7.1 surround sound.

The software's built-in documentation provides more detailed instructions.

Status LED Indications

• Single blink red: Connected, battery low
• Single blink green: Connected, battery normal
• Rapid blink red: Disconnected, battery low
• Rapid blink green: Disconnected, battery normal
• Solid amber: Battery charging
• Solid green: Battery charged
• Rapid blink amber: Pairing mode

Audio Settings

• Press the JOG DIAL briefly (0.1-0.5 seconds) to toggle EQ settings.
• Press the JOG DIAL moderately (0.6-2 seconds) to toggle 7.1 surround sound.

Mic Control

• Press the mic mute button briefly (0.1-0.5 seconds) to toggle mute on/off.
• Press and hold the mic mute button (2-4 seconds) to toggle sidetone on/off.

Note: iCUE software can also be used to control these features.

For Optimal Wireless Performance

• Place the wireless USB transmitter in an open, unobstructed area.
• Ensure the battery is fully charged before initial use.
• Avoid leaving the battery fully discharged for long periods; battery life is maximized by keeping it in a partially charged state.
• If RGB lighting effects are not important, disable them in iCUE to extend battery life.
• Promptly remove the USB charging cable after the headset has been fully charged.
• Keep the headset at room temperature (20-30°C or 68-86°F).

Compliance Information

Applicant Name: CORSAIR Memory, Inc.

Product Name: Headset / USB dongle

Model No.: RDA0011 / RDA0012

Manufacturer & Country of Origin: CORSAIR Memory, Inc. / Made in China