QFX BT-102 Instruction Manual

Main Unit Overview

The main unit features the following components:

• 1. PLAY/PAUSE/PAIR/SCAN BUTTON
• 2. SOURCE BUTTON
• 3. POWER BUTTON
• 4. VOL- BUTTON
• 5. VOL+ BUTTON
• 6. SPEAKERS
• 7. LCD DISPLAY
• 8. BLUETOOTH INDICATOR
• 9. REMOTE SENSOR
• 10. SD CARD SLOT
• 11. USB PORT
• 12. DC IN JACK
• 13. AUX IN JACK
• 14. FM ANTENNA

Please read the following instructions prior to operating your unit. The manufacturer of this unit follows a principle of continuous improvement and has no responsibility for any changes that are made to the unit or any liability for these changes. Thank you for choosing our products.

Remote Control Overview

The remote control includes:

• 1. POWER BUTTON
• 2. MUTE BUTTON
• 3. NEXT/FAST FORWARD BUTTON
• 4. VOL+ BUTTON
• 5. PREVIOUS/FAST BACKWARD BUTTON
• 6. VOL- BUTTON
• 7. PLAY/PAUSE/PAIR/SCAN BUTTON
• 8. CLK BUTTON
• 9. SOURCE BUTTON
• 10. TUN+ BUTTON
• 11. TUN- BUTTON
• 12. MEM BUTTON

Power Supply

Plug the AC/DC adapter into the DC jack on the unit and to the main power.

How to Set Time

1. At standby mode, press the CLK button on the remote once; the display lights up.
2. Press the CLK button again; the hour flashes on the display.
3. Use the PREVIOUS/NEXT button on the remote to adjust the hour and press the CLK button to confirm.
4. The minute starts blinking. Use the PREVIOUS/NEXT button on the remote to adjust the minute and press the CLK button to confirm.
5. During playback, press the CLK button to check the current time; press the button again to resume the previous display.

Note: The time can only be set at the standby mode.

Bluetooth Operating

This unit can receive stereo audio signals from a Bluetooth stereo audio source device.

1. Power on the unit by pressing the POWER button. Switch to Bluetooth mode by pressing SOURCE repeatedly until "PAIR" shows on the display.
2. The LED indicator blinks rapidly while pairing.
3. Pair and connect to QFX BT-102 on your Bluetooth audio source device. If prompted for a passcode, enter "0000".
4. Pairing is successful when the LED indicator lights solid blue, and the unit is ready to stream music.
5. Press the PLAY/PAUSE/PAIR/SCAN button to pause or resume playback.
6. During playback, press the PREVIOUS button once to go to the beginning of the current track. Press the PREVIOUS button twice continuously to skip to the previous track.
7. During playback, press the NEXT button on the remote to skip to the next track.
8. Press and hold the PREVIOUS/NEXT button on the remote to search through the current track forward or backward. Release the button to resume normal play.

Note: Pairing mode is canceled after approximately 1.5 minutes.

Re-connect to the Bluetooth Audio Source Device: If the device is already paired with the QFX BT-102 but has become unconnected, ensure both Bluetooth devices are turned on. Press and hold the PLAY/PAUSE/PAIR/SCAN button to re-link the audio source device. The Bluetooth indicator will blink for about 1.5 minutes. Select QFX BT-102 on the audio source device. The Bluetooth indicator will turn solid blue if the connection is successful.

FM Radio

Tuning the FM Radio

1. Power on the unit and press the SOURCE button repeatedly to switch to TUNER (radio) mode.
2. Press the TUN+/TUN- button on the remote to fine-tune the radio station. Press and hold the TUN+/- button on the unit to auto-search for radio stations forward or backward from the current frequency. The unit will broadcast the first available station found and stop searching.
3. Press and hold the PLAY/PAUSE/PAIR/SCAN button to auto-search the radio station from the beginning to the end of the frequency range. The unit will store all available stations as presets (up to 20 stations).

Storing Your Favorite Radio Station

1. During playback, press the MEM button on the remote. The memory cell number will flash on the display.
2. Use the TUN +/- button on the remote or the PLAY/PAUSE/PAIR/SCAN button to select the desired memory cell.
3. Confirm your selection by pressing the MEM button again.
4. During radio playback, press the PLAY/PAUSE/PAIR/SCAN button repeatedly to recall stored stations.

Mute the Unit

During playback, press the MUTE button on the remote to turn off the audio. Press the button again to resume the audio.

Volume Level Adjustment

Press the VOL+/- button to adjust the volume output level.

USB/Card Playback

1. Power on the unit and insert a USB or SD card.
2. Press the SOURCE button repeatedly to switch to USB or card mode. Playback will start automatically.
3. Press the NEXT button on the remote to skip to the next track. Press and hold to search forward through the track.
4. Press the PREVIOUS button on the remote to skip to the previous track. Press and hold to search backward through the track.

Audio In

1. Connect the AUX IN jack on the unit to an audio source (e.g., DVD player) using an RCA cable.
2. Press the POWER button to turn the unit on.
3. Press the SOURCE button repeatedly to switch to AUX mode.
4. Use the native controls on the connected audio device to begin playing music through the unit.

Trouble Shooting

Important Safety Instructions

• The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus.
• When the AC/DC adapter is used as the disconnect device, the disconnect device shall remain readily operable. To completely disconnect the power input, the AC/DC adapter shall be disconnected from the mains completely.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• Maintain minimum distances of 2.0cm around the apparatus for sufficient ventilation. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, or curtains.
• This apparatus is for use in tropical and/or moderate climates.
• Attention should be drawn to the environmental aspects of battery disposal.
• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Batteries shall not be exposed to excessive heat such as sunshine, fire, or the like.
• The marking plate is located at the back of the apparatus.