LANCOM ISG-1000 Quick Reference Guide
Cloud-ready
Mounting and Connecting the Device
This section describes the physical connections and controls of the LANCOM ISG-1000.
Device Ports and Controls
- a USB interface: For connecting USB printers or USB storage devices.
- b Serial configuration interface: Use the included serial cable to connect to a configuration/monitoring device.
- c SFP / TP Ethernet interfaces (combo ports): For inserting SFP modules and connecting compatible cables. SFP modules and cables are not included.
- d TP Ethernet interfaces (ETH 1 - ETH 4): Connect to a PC or LAN switch using enclosed kiwi-colored cables.
- e TP Ethernet interface (ETH 5): Connect to a PC or LAN switch using an enclosed kiwi-colored cable.
- f Reset button: Press for up to 5 seconds for a device restart. Press until first LED flash for configuration reset and restart.
- g Power connector and grounding point (device back side): Supply power via the power connector using the supplied IEC power cable.
- h Grounding: [Attention] High touch current possible! Connect to earth before connecting the power supply. Remove the blind screw and use the enclosed grounding screw.
Setup Recommendations
Please observe the following when setting up the device:
- The mains plug must be freely accessible.
- For desktop operation, attach the adhesive rubber footpads.
- Do not rest objects on the device or stack multiple devices.
- Keep ventilation slots clear.
- Mount the device into a 19" unit in a server cabinet using provided screws and brackets.
[Important] Before initial startup, consult the installation guide for intended use. Operate the device only with a professionally installed power supply at a nearby, accessible power socket.
LED Status Indicators
The following table details the status of the device's LEDs:
POWER LED Status
| Status | Description |
|---|---|
| Off | Device switched off |
| Green, permanently* | Device operational, or device paired/claimed and LANCOM Management Cloud (LMC) accessible |
| Green / red, blinking | No password set. Configuration data is unprotected. |
| Red, blinking | Charge or time limit reached |
| 1x green inverse blinking* | Connection to LMC active, pairing OK, device not claimed |
| 2x green inverse blinking* | Pairing error, or LMC activation code not available |
| 3x green inverse blinking* | LMC not accessible, or communication error |
[Note] *Additional power LED statuses are displayed in 5-second rotation if the device is managed by LANCOM Management Cloud.
TEMP LED Status
| Status | Description |
|---|---|
| Green, permanently | CPU temperature OK |
| Red, blinking | Hardware failure of the fan or CPU temperature too high; additional acoustic signal. |
LCD Display
The LCD display rotates through the following information:
- Device name
- Firmware version
- Device temperature
- Date and time
- CPU load
- Memory usage
- Number of VPN tunnels
- Data transfer in reception direction
- Data transfer in transmission direction
ETH 1 - ETH 4 TP LED Status
| LEDs | Description |
|---|---|
| Both LEDs off | No networking device attached |
| Green, permanently | Connection to network device operational, no data traffic |
| Green, flickering | Data transmission |
| Orange off | 1000 Mbps |
| Orange, permanently | 10 / 100 Mbps |
ETH 1 - ETH 4 SFP LED Status
| LEDs | Description |
|---|---|
| Both LEDs off | No networking device attached |
| Green, permanently | Connection to network device operational, no data traffic |
| Green, flickering | Data transmission |
| Orange off | 1000 Mbps |
| Orange, permanently | 10 / 100 Mbps |
ETH 5 LED Status
| LEDs | Description |
|---|---|
| Both LEDs off | No networking device attached |
| Green, permanently | Connection to network device operational, no data traffic |
| Green, flickering | Data transmission |
| Orange off | 1000 Mbps |
| Orange, permanently | 10 / 100 Mbps |
Technical Data
Hardware
| Parameter | Specification |
|---|---|
| Power supply | Internal power supply unit (110–230 V, 50–60 Hz) |
| Power consumption | 40 W |
| Environment | Temperature range 5–40 °C; humidity 0–95 %; non-condensing |
| Housing | Robust metal housing, 19" 1U with removable mounting brackets, network connectors on the front |
| Number of fans | 3 |
Interfaces
| Interface | Description |
|---|---|
| ETH | 4 individual 10 / 100 / 1000-Mbps Gigabit Ethernet ports (ETH 1 - ETH 4); 1x Gigabit Ethernet port (ETH 5). Up to 4 ports can be switched as additional WAN ports with load balancing. Ethernet ports can be electrically disabled within LCOS configuration. |
| USB | USB 2.0 Hi-Speed host port for connecting USB printers (USB print server) or USB data media (FAT file system); bi-directional data exchange is possible (max. 480 Mbps) |
| Serial Interface | Serial configuration interface |
WAN Protocols
| Protocol | Details |
|---|---|
| Ethernet | PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and plain Ethernet (with or without DHCP), VLAN, IP |
Declaration of Conformity
LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc
Package Content
Documentation
- Quick Reference Guide (DE, EN)
- Installation Guide (DE/EN)
Accessories
- 2 Ethernet cables, 3 m (kiwi colored connectors)
- 1 serial configuration cable 1.5 m
- 1 IEC power cord 230 V (not for WW devices)
- 1 grounding screw
Software Licenses
This product contains separate open-source software components subject to their own licenses, particularly the General Public License (GPL). License information for the device firmware (LCOS) is available via the device's WEBconfig interface under “Extras > License information”. Source files for corresponding software components will be made available on a download server upon request, if required by the license.
Compliance proofs for products: LANCOM Systems GmbH
