ELECTRIC CREPE MAKER

Adexa CATERING EQUIPMENT DIRECT

The Electric Crepe Maker design combines the advantages of stylish design, efficient construction, ease of operation and simple maintenance. The Crepe maker temperature can be easily adjusted to suit cooking requirements, and, while mainly used for crepe.

Notes

• This product is intended for commercial use only.
• Do not disassemble or modify the machine.
• Before cleaning, disconnect power and allow machine to cool.
• Do not immerse in water or spray water onto the grills. Water may cause short circuit and injury or damage.
• To avoid damage, do not jam materials onto the grill or place heavy objects there.
• When the machine is in use, the body and grill plates are hot, and will cause burns if touched. Do not use an un-grounded power supply cord.
• It is recommended that the machine be unplugged during thunderstorms to avoid potential damage from nearby lightning strikes.
• Avoid damaging the controls or grill surfaces with sharp or heavy objects.
• Turn off power after daily use.
• Do not use the machine with a damaged power cord.
• Any internal repair or maintenance should be performed by a factory authorized repair technician.

Features

1. External shell and grease collector tray are stainless steel
2. The grill is easy to use and maintain
3. Grill temperatures are designed may be set for different uses at the same time (double unit)
4. Convenient independent temperature controls are easy to set and may result in overall power savings (double unit).
5. Over-heat temperature controller for safety using

Instructions for First Time Use

There is a thin layer of wax paper on top of the grill plate that must be removed prior to using the griddle. In order to protect the plates of your new grill during transportation, a layer of food-safe oil was coated on the surface prior to shipment. This oil is harmless, but must be removed before you begin to use. To remove, preheat the grill until the oil liquefies. Next, carefully wipe away the melted oil with a clean, soft cloth. Once all of the oil is removed you can begin to use your grill.

Specification

Mainly part

A diagram shows the main parts of the crepe maker. The parts are labeled with numbers and descriptions:

• 1. Drip Tray
• 2. Temperature Limiter
• 3. Heat Indicator
• 4. Power Indicator
• 5. On&Off Power Switch (EC-1N without the device)
• 6. Thermostat
• 7. Rubber Feet
• 8. Heavy Duty Cast Iron Plate with Teflon Coating
• 9. T-Spreader

Component Descriptions

• Thermostat: 50-300°C: Used to set or adjust the temperature of the cooking plate. The numbers on the dial correspond with the grill plate temperature. The “0” position is off.
• Reset Bottom (Over-temperature Device): The power would be cut off automatically once the temperature exceeds 350°C.
• Power Indicator: This light indicates the power is on.
• Heat Indicator: This light indicates the element is heating. Once the set temperature has been reached, the light will go out. The unit will continue to maintain heat and temperature with the light cycling. This is not a power indicator light.
• Drip Tray: A container that collects grease, oil and liquid from the bottom grill plate. This is removable for draining and cleaning.
• On&Off Power Switch: Turn on the power, the power indicator “Green Light” would be on.

How to use it

1. Plug the power cord into the appropriate outlet.
2. Turn on the power switch; the green "Power" light will illuminate.
3. Set the desired temperature by turning the rotary temperature knob clockwise.
4. The heating element will begin to heat up and the yellow "Heating" light will illuminate.
5. When the temperature reaches the desired setting, the yellow "Heating" light will cycle on and off with the heating element to maintain the set temperature.
6. *Pour a teaspoon of vegetable-based cooking oil onto the center of the griddle. *Spread the oil evenly over the entire griddle surface. *Wipe the griddle after every two crepes. * If the crepes begin sticking, spread a small amount of oil around the griddle. *Use additional oil on the griddle in between crepes as needed
7. Turn temperature knob to the "Off" position to turn the yellow "Heating" light and heating element off.
8. Turn off power switch; the green “Power” light off.

Cleaning and Maintenance

• Disconnect machine before cleaning and allow to cool.
• Unplug the unit.
• Use only a damp towel with non-corrosive cleaner. Do not immerse or flush with water.
• Wipe down outside surface to remove any soil.
• Store in a dry clean area when not in use.
• Wipe the griddle using a clean, non-abrasive cloth.
• Wipe the frame of the unit with a non-abrasive cloth dampened in warm water and a mild soap.
• Stubborn stains may be removed with a good stainless steel cleaner. Hard to reach areas should be cleaned with a small brush and mild soap.
• Dry the frame of the unit using a clean, dry, non-abrasive cloth.

NOTE: Oil and fats will build up on the griddle surface over time. This eventually will begin affecting the performance of the Crepe Maker. An abrasive stone is available as an accessory (see OPTIONS AND ACCESSORIES). Use the abrasive stone to strip the griddle on a regular basis to maintain performance of the unit. The “Seasoning the Griddle" procedure must be performed after stripping the griddle.

Trouble Shooting

Do not use the machine if any of the above occur.

Any troubleshooting corrections should be performed by a qualified technician.

Daily Check

Before using the machine, visually inspect for any signs of damage or frayed power cord. Be certain machine is on a level countertop.

After turning it on, check for anything unusual before you use it.

Inspect the machine every day before using. If there is any question about operation, do not use.

Explosive View: EC1

Diagram showing exploded view of EC1 model with numbered parts and a parts list:

Circuit Diagram EC1

A circuit diagram for the EC1 model is provided, showing connections between components like Thermostat (ST1), Power Switch (SA1), Heater (EH), and indicators (HL1, HL2).

Explosive View: EC2

Diagram showing exploded view of EC2 model with numbered parts and a parts list:

Circuit Diagram EC2

A circuit diagram for the EC2 model is provided, showing connections between components like Thermostats (ST1, ST3), Power Switches (SA1, SA2), Heaters (EH1, EH2), and indicators (HL1-HL4).

Explosive View: EC1N

Diagram showing exploded view of EC1N model with numbered parts and a parts list:

Circuit Diagram EC1N

A circuit diagram for the EC1N model is provided, showing connections between components like Thermostat (ST1), Heater (EH), and indicators (HL1, HL2).