ICE MAKER INSTRUCTION MANUAL

PRECAUTIONS FOR INSTALLATION

⚠️ WARNING Installation should be performed only by the dealer or a qualified expert. Attempting to install the unit yourself could result in water leakage, refrigerant leakage, electrical shock, or fire.

PRECAUTIONS FOR USE

⚠️ WARNING All repairs, disassembly and modifications should be performed only by qualified technicians. Attempting to perform these yourself could result in a fire, malfunction, and injury.

⚠️ WARNING Never splash water directly onto the product or wash with water as short-circuit and electrical leakage could result.

⚠️ WARNING Never use flammable spray cans or leave flammable substances near the unit. Sparks from electrical switches could result in explosion and fire.

⚠️ WARNING Do not damage, modify, excessively bend, strain, twist or bundle up the power cord. Also, placing heavy objects the power cord or squeezing it in a tight place could damage it, possible resulting in electrical shock or fire.

⚠️ WARNING Use a dedicated wall outlet. Do not use extension cords or convenience receptacles as this could result in electrical shock, overheating and a fire.

BEFORE USE

• Remove shipping package, tape, etc, and leave doors open ventilation for a while.
• Check carefully if the unit has been destroyed during the transportation after open the package. The unit is cleaned before shipment. However, clean the compartment interior once after delivery.
• Open the door of storage chamber, take out the accessories from it.
• Fixing the feet: Pad the bottom of the unit with the foam supplied, revolve 4 adjustable feet into corresponding rivet-nut.
• Level the ice maker by adjusting the feet.

Connect the water supply

• This unit supply a flow pipe, the elbow side of which connect the water tie-in in back of Unit, and the other side connect 3/4” whorl pipe, must install a soft gasket in the two joint avoiding leak.
• Install a water valve nearby the water supply pipeline for easy controlling water supply.
• The water used in this unit must accord with the international standard on drinking water; you can install the water filtrated system considering the actual condition of water supply.

DRAIN

• Joint a drain which manufacturer supply to a drain joint in back of unit, after fix it, insert the other side to the channel. The lowest point of drain must overtop the highest point of the channel avoiding refluence.

Electric connecting

• Voltage range: 187~242V/60Hz, 50Hz; if current fluctuate, add a regulator n. Must supply a individual three-hole plug and earth well.

Fuction instruction

• This unit have such functions as water automaticly, making ice falling ice, ice-full stopping automaticly.
• Once power and water supply well, this unit start water, makeing ice, falling ice circularly have such function as water automatically, making ice falling ice, ice-full stopping automatically.

Operation instruction

• During making ice in the first time, if water is lacking, open the door, uncover the white hangings, add water to the flume untill drain overflow.
• After ice storage chamber is full, the control system will cut off the power automaticlly, as well as the compressor stop to operate.
• After ice is taken out from storage chamber (about 3 minutes), the control system will switch to ice-making mode automatically.

EXTREME CONDITION PARAMETER

• The lowest room temperature : 10
• The highest room temperature : 43
• The lowest water-supply press : 0.2MPa
• The highest water-supply press: 0.5MPa
• The lowest water temperature : 2
• The highest water temperature : 35

WAIT 5 MINUTES OR MORE BEFORE RE-STARTING

Restarting the unit immediately after it has been turned off may cause fuses to blow and activate the circuit-breaker, the compressor may be overloaded, and/or other damage may occur.

EFFICIENT USE

Please follow the below instruction, you could save energy.

• To prevent cold air from escaping, open and close the door quickly and keep the door opened for as short a time as possible.
• Please install the unit in the place which is well-ventilated.

By the raise of circumstance temperature and water temperature, the ice-making capacity reduces. (Details in graph down)

Ice-making Graph

A graph showing ice-making capacity percentage (from 80% to 120%) on the Y-axis against circumstance temperature in degrees Celsius (from 10°C to 32°C) on the X-axis. The graph shows a downward trend, indicating reduced capacity at higher temperatures.

Note: This graph shows the actual ice-making capacity by 15 water; as water temperature raise, ice-making capacity reduces.

CLEAN CONDENSER

• Clean condenser once half year to keep it well-ventilated.
• Cut power off and cool condenser before cleaning.
• Do not touch the aliform pieces during cleaning to avoid cut.
• After taking out the front faceplate, use cleaner or brush to do it.

CLEAN NOZZLE

• Take out spray bracket, wrest the spray or nut one by one, clean spray and centrifugal pieces by clean water.

CLEAN INNER FLUME FILTER

• Wrest the screw cap on inner flume filter, take out stainless steel filter, clean it and put back.

CLEAN WEV. FILTER

• Wrest the water pipe in back of unit, clean water-electromagnet-valve filter.

1 WHEN NOT USED FOR A LONG PERIOD

• Remove all items from the compartment and disconnect the power cord plug from the wall outlet.
• Clean the compartment interior and wipe away all water. Come away the water supply pipe from the back of unit, and drain all water in it.
• To prevent mold formation and bad smell, leave the door open to dry the compartment completely.

2 TRANSPORTATION

• Disconnect the power cord plug from the wall outlet.
• When moving the ice maker, make sure that the feet do not damage the power cord.
• Do not let the feet hit against floor steps, thresholds, etc.

3 TEMPORARY STORAGE

• Affix a piece of wood, etc. Between the door and main unit to prevent complete closing of the door.
• Make sure not to store the unused ice maker at a location where children play.
• Should a child enter the compartment and the door is closed, the child may not be able to open the door from the inside.

REQUIRED INFORMATION

1. Nature of malfunction (as accurately as possible)
2. Product number (inscribed on badge)
3. Serial number
4. Customer's name, address, phone number
5. Year and date of purchase
6. Desired date for service visit