Schneider Electric ComPacT NSX 9-Wire Moving Connector

Important Notes and Safety Information

Please Note: Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. Schneider Electric assumes no responsibility for any consequences arising out of the use of this material.

Remarque Importante: L'installation, l'utilisation, la réparation et la maintenance des équipements électriques doivent être assurées par du personnel qualifié uniquement. Schneider Electric décline toute responsabilité quant aux conséquences de l'utilisation de cet appareil.

Tenga en Cuenta: La instalación, manejo, puesta en servicio y mantenimiento de equipos eléctricos deberán ser realizados sólo por personal cualificado. Schneider Electric no se hace responsable de ninguna de las consecuencias del uso de este material.

请注意: 电气设备的安装、操作、维修和维护工作仅限于合格人员执行。Schneider Electric不承担由于使用本资料所引起的任何后果。

Connection Diagrams and Pin Assignments

Module OF1 AX1

This diagram illustrates the OF1 AX1 module. It features connection terminals for pins 4, 5, and 6, corresponding to external terminals 14, 12, and 11 respectively. This module is compatible with SD1, SD2, and SD4 contacts.

• Pin 4 → Terminal 14
• Pin 5 → Terminal 12
• Pin 6 → Terminal 11

Module MN / MX SHT / UVR

This diagram shows the MN/MX SHT/UVR module. It has connection terminals for pins 9, 8, and 7, corresponding to external terminals C1/D1, C2, and D2 respectively. This module is compatible with SD3 contacts.

• Pin 9 → Terminal C1/D1
• Pin 8 → Terminal C2
• Pin 7 → Terminal D2

Module SD AL

This diagram illustrates the SD AL module, showing connection points for pins 1, 2, and 3.

• Pin 1
• Pin 2
• Pin 3

Module SDE OAL

This diagram shows the SDE OAL module with connection terminals for pins 1, 2, and 3, corresponding to external terminals 84, 82, and 81 respectively.

• Pin 1 → Terminal 84
• Pin 2 → Terminal 82
• Pin 3 → Terminal 81

Module OF2 AX2 / SDV

This diagram illustrates the OF2 AX2 and SDV modules. They feature connection terminals for pins 4, 5, and 6, corresponding to external terminals 24/74, 22/72, and 21/71 respectively.

• Pin 4 → Terminal 24/74
• Pin 5 → Terminal 22/72
• Pin 6 → Terminal 21/71

MT / MTc Modules with NSX Cord and BSCM

This section details the connection of MT and MTc accessory modules using the NSX cord and BSCM (Breaker Status Communication Module). The diagrams show wiring configurations for remote control and communication.

MT Module Connections:

The MT module connects via the NSX cord to the breaker. Key terminals are:

• Pin 9 (A2)
• Pin 2 (L1)
• Pin 3 (A1)
• Pin 8 (A4)
• Pin 7 (B4)

MTc Module Connections:

The MTc module connects via the NSX cord. Key terminals are:

• Pin 8 (A1)
• Pin 2 (B4)

MicroLogic 5.2/6.2 with 24V Power and ZSI Out

This diagram shows the connection of the MicroLogic 5.2/6.2 electronic trip unit. It includes connections for a 24V power supply and the Zone Selective Interlocking (ZSI) output.

24V Power Supply:

• Pin 1 (+)
• Pin 3 (-)

ZSI Output:

• Pin 5 (Z2: ZSI out)
• Pin 4 (Z1: ZSI out source)

SDV Module Installation

The installation of the SDV (Earth Leakage Indication) module involves the following steps:

1. Prepare unused wires.
2. Insert wires into the SDV module.
3. Connect the SDV module to the breaker. Ensure a torque of 1.2 N.m (10.5 lb-in) is applied during connection.
4. Connect the module wires to the breaker terminals.

The module indicates operational states such as OFF and ON.

Manufacturer Information

Schneider Electric Industries SAS
35 rue Joseph Monier
CS 30323
F - 92506 Rueil Malmaison Cedex
www.se.com

Schneider Electric Limited
Stafford Park 5
Telford, TF3 3BL
United Kingdom
www.se.com/uk