Machenike MCF27F300L/MCF27F300L-W Gaming Monitor

Introduction

Thank you for choosing a Machenike monitor. Please read this manual carefully before using the device and keep it for future reference. The images used in this manual are for demonstration purposes and may differ slightly from the actual product.

The manufacturer reserves the right to make changes to this manual without prior notice.

This product is intended for domestic use only and cannot be used for industrial or commercial purposes. Transport and store the product in its original packaging, following the handling symbols indicated on it. Handle with care during loading, unloading, and transportation. Transport and storage facilities must protect the product from atmospheric precipitation and mechanical damage.

If any malfunctions are detected, immediately stop using the device and take it to the nearest authorized HAIER service center for testing, replacement, or repair. For safety reasons, all repair and maintenance work must be performed only by authorized HAIER service centers.

Service center addresses and phone numbers can be found on the website haieronline.ru or by calling 8-800-250-43-05.

Safety Precautions

Read the following instructions carefully and follow them to avoid hazards or legal violations. Information on the WEEE logo (Waste Electrical and Electronic Equipment):

The WEEE logo on the product or its packaging indicates that this product must not be disposed of or recycled with household waste. You are responsible for delivering all your electronic devices or electrical equipment to a collection point for hazardous waste for proper disposal. Collection and proper disposal of electronic devices and electrical equipment ensure the conservation of natural resources. Recycling of electronic devices and electrical equipment ensures the preservation of human health and environmental cleanliness.

The socket for the connected equipment should be installed near the equipment and be easily accessible.

HDMI™ HDMI is a high-definition multimedia interface and a trademark of HDMI Licensing Administrator, Inc., registered in the United States and other countries.

• The product is suitable for use in non-tropical zones at altitudes below 2,000 meters above sea level.
• Do not drop the monitor or subject it to strong impacts.
• Do not use the device in conditions of extremely low or high temperatures (< 35 °C), high humidity, or dusty environments for extended periods.
• Do not expose the monitor to direct sunlight.
• Do not expose the device to strong magnetic fields or static electricity.
• If water or other liquids spill onto the device, immediately turn it off and do not use it until it has dried.
• Do not clean the monitor with cleaning agents containing chemical elements or other liquids to avoid damage caused by corrosion and moisture. If cleaning is necessary, use a dry soft cloth.
• Our company is not responsible for data loss or deletion caused by product malfunction, software or hardware failure, technical maintenance, or any other circumstances.
• Do not disassemble the device yourself to avoid voiding the warranty.
• The startup guide and relevant software may be updated at any time. To download the updated version, visit the website https://haieronline.ru/support. Otherwise, no notifications will be provided.
• Observe all warnings and instructions marked on the monitor.
• Do not use accessories not recommended by the manufacturer, as this may cause danger.
• Do not place the monitor near water sources such as bathtubs, washbasins, kitchen sinks, washing machines, damp basements, or swimming pools.
• Do not place the monitor on an unstable platform or tabletop, as it may fall and injure someone or damage the monitor.
• Use only manufacturer-recommended or supplied mounts for desktop, wall, or shelf installation. Follow the manufacturer's instructions and use manufacturer-approved mounts.
• When installing on a wall or shelf, follow the manufacturer's instructions and use manufacturer-approved mounting tools.
• The slots and openings on the case or its rear and bottom parts are for ventilation and ensure reliable operation of the device, preventing overheating.
• Do not place the monitor on a bed, sofa, carpet, or other similar surface to avoid blocking the ventilation openings.
• Do not place the monitor near or on top of a heat source, such as a radiator. Do not install the monitor in a niche or furniture unless it is adequately ventilated.
• The monitor should only be used with the type of power source indicated on its rating plate. If you have questions about the type of power source, contact your dealer.
• Do not leave the power cord where it can be accidentally touched by users.
• For additional protection, turn off the power when the monitor is not in use; unplug the power adapter from the outlet to prevent voltage surges through the power cord.
• Do not overload the outlet or extend the power cord, as this may lead to fire or electric shock.
• Do not allow foreign objects to enter the case slots to prevent high-voltage points or short circuits, which could cause fire or electric shock.
• If the monitor is faulty, do not open the case or attempt to repair it yourself. Contact the after-sales service center for inspection and repair.
• In the following cases, first unplug the monitor from the outlet and contact the after-sales service center for inspection and repair:
  • The power cord or plug is damaged.
  • Liquid has been spilled on the monitor.
  • Rain or water has come into contact with the monitor.
  • You have dropped the monitor and damaged the casing.
• The image on the monitor does not meet expectations, and you have used all available settings in the built-in menu.

1. Device Assembly

Monitor Stand Installation

Step 1: Take the base and connect it to the monitor stand as shown in the figure.

Step 2: Turn the screws to secure both the stand and the base.

Step 3: Connect the assembled stand to the monitor. Install the bracket until it clicks.

Monitor Stand Removal

Step 1: Remove the bracket, then press the quick-release button upwards.

Step 2: Turn the screws to detach the monitor stand from the base.

Step 3: Pull the base in the direction shown in the figure and disassemble the stand.

2. Connecting the Monitor

1. Turn off the computer and unplug the power cord from the outlet.
2. Connect the video cable to the appropriate port on the back of the monitor.
3. Connect the power cord to the DC input port on the back of the monitor, and plug the other end of the power cord into the nearest outlet.
4. Turn on the computer and monitor power. If an image appears on the monitor, the connection is correct. If there is no image on the display, check all cables.

Port Connections:

• HDMI 1 Port
• HDMI 2 Port
• Display Port 1 Port
• Display Port 2 Port
• Headphone Audio Output
• DC IN Power Port

3. Control Buttons

Five-Position Joystick

Power Button

4. On-Screen Menu (OSD)

The on-screen menu is used to select and change monitor settings and image parameters. A brief description of the OSD sections:

5. Technical Specifications

Package Contents MCF27F300L/MCF27F300L-W

• MCF27F300L/MCF27F300L-W Monitor
• Desktop Monitor Mount
• User Manual
• Warranty Card
• Power Adapter
• HDMI Cable
• Display Port Cable

Customer Service

We recommend contacting Haier customer support and using original spare parts. If you encounter problems with your home appliance, please contact:

• Your official dealer or our call center:
• 8-800-250-43-05 (Russia)
• 8-10-800-2000-17-06 (Belarus)
• Visit the website haieronline.ru to submit a service request and find answers to frequently asked questions. When contacting our service center, please prepare the following information, which can be found on the nameplate and receipt:

Model: _______________

Serial Number: _______________

Date of Purchase: _______________

Also, please check for the presence of warranty and sales documents. Important! The absence of a serial number on the device makes it impossible for the Manufacturer to identify the device and, consequently, its warranty service. Do not remove the factory identification plates from the device. The absence of factory plates may lead to refusal to fulfill warranty obligations. This document may be subject to change without prior notice.

The manufacturer reserves the right to make changes to the design and configuration of the product without additional notice.

Manufacturer Information

RU

Manufacturer, country of production, date of production, and warranty period are indicated on the packaging. Before using the device, carefully read this user manual and save it for future use.

Manufacturer: «Haier Overseas Electric Appliances Corp. Ltd.», Room S401, Haier Brand building, Haier Industry park Hi-tech Zone, Laoshan District, Qingdao, China

Authorized Organization / Importer: LLC «KHAR», 121099, Moscow city, Novinsky Boulevard, building 8, floor 16, office 1601.

Authorized Organization in the Republic of Kazakhstan: TOO «Haier Middle Asia», 050000, Almaty city, Medeu district, Dostyk Avenue, building 210.

Made in China

KZ

Дайындаушы, өндіріс елі, өндіріс күні және кепілдік мерзімі қаптамада көрсетілген. Құрылғыны пайдаланбас бұрын, осы пайдалану жөніндегі нұсқаулықты мұқият оқып шығып, алдағы уақытта пайдалану үшін сақтап қойыңыз.

Өндіруші: «Haier Overseas Electric Appliances Corp. Ltd.», Room S401, Haier Brand building, Haier Industry park Hi-tech Zone, Laoshan District, Qingdao, China

Қазақстан Республикасындағы уәкілетті ұйым/импорттаушы: «Хайер Мидл Эйжа» ЖШС, 050000, Алматы қаласы, Медеу ауданы, Достық даңғылы, 210 ғимарат.

Қытайда жасалған

Recycling symbols: [recycle], [CE], [TPM]