Machenike L7 Mix Wireless Gaming Mouse

Specifications

Model Name: L7 Mix

Size: 118.8*63.8*39.3 mm (length*width*height)

Weight: 50g ± 2g

Sensor: PAW3395

System Compatibility

Compatible with WINDOWS, Mac OS, and Linux systems.

Key Functions and Features

Key Functions

The mouse features 6 keys in total: left, center, right, forward, backward, DPI cycle, and connection switching.

Connection Switching Key: Left position is for Bluetooth connection, middle position is for wired connection, and the right position is for 2.4G connection.

Indicator Light

The light on the left side of the mouse serves as a low battery indicator, DPI indicator, and charging indicator.

Low Battery: The left light flashes red when the voltage is low.
Charging: The left light flashes blue while charging.
Fully Charged: The left light flashes green when fully charged.
The indicator also shows the current DPI setting.

DPI Levels

There are six DPI levels:

400 (indicated by red light)
800 (indicated by green light) - default
1600 (indicated by blue light)
3200 (indicated by yellow light)
6400 (indicated by purple light)
26000 (indicated by cyan light)

Return Rate

Four levels of return rate are available: 125Hz, 250Hz, 500Hz (default), and 1000Hz.

Power Switch

The power switch is a pull switch located at the bottom of the mouse.

Motion Sync

The mouse drive includes the Motion Sync function.

LOD Adjustment

Features an LOD (Lift-Off Distance) adjustment function with two levels: 1mm and 2mm.

Sleep and Wake Up Modes

Sleep Mode: In wireless mode, if the mouse performs no operations for 3 minutes, it enters sleep mode, and the indicator light turns off. Press any button or move the mouse to wake it up, and the indicator light will illuminate again.

Deep Sleep Mode: In wireless mode, if the mouse performs no operations for 15 minutes, it enters a deep sleep state where all LEDs and sensors cease to function. The mouse can only be woken up by pressing any button for the MCU to resume normal operation.

Connectivity and Coding

Wired and Wireless Switching Mode

The mouse automatically switches between wired and wireless modes. It defaults to wired mode when the data cable is plugged in and switches to wireless mode when the data cable is unplugged.

Coding Method

This method is suitable for both 2.4G and Bluetooth modes. To initiate code broadcast, press and hold the left, right, and middle buttons simultaneously for 3 seconds.

Connection Methods

Wired Connection: When the data cable is plugged in, the connection mode is fixed to wired mode by default, prioritizing the wired connection.
2.4G Connection: For the first-time connection, no coding is required. Simply plug the USB receiver into a computer port and use the mouse.
Bluetooth Connection: When broadcasting, search for the model name "GM-928" on your computer via Bluetooth and click to connect.

Performance Specifications

Click Delay: The parameter range for left and right button click delay is 2~3ms.
Wireless Transmission Distance: The effective wireless transmission distance is 8~10 meters.

Charging

The mouse can be used with a charging stand. The charging indicator is described in the "Indicator Light" section. The charging current is set to 200mA constant current charging. The mouse itself is also equipped with a charging function.

FCC Compliance

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note on Interference

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

	Qingdao Machenike Technology L8MAX Mouse User Manual User manual for the Qingdao Machenike Technology L8MAX mouse, detailing features, setup, and usage instructions.
	M7 Pro Dual-Mode Mouse User Manual and Specifications Comprehensive guide for the MACHENIKE M7 Pro dual-mode mouse, covering setup, features, DPI settings, lighting customization, power saving, and technical specifications for both 3104 and 3395 sensor versions.
	MACHENIKE L8 Pro Dual-Mode Mouse User Guide Comprehensive guide for the MACHENIKE L8 Pro Dual-Mode Mouse, covering installation, connection modes (2.4GHz, Wired, Bluetooth), pairing, lighting controls, power saving, and troubleshooting.
	Machenike Controller G3 V2 Radio Test Report FCC ID 2BBT5-G3V2 This radio test report details the compliance of the Machenike Controller, Model G3 V2 (FCC ID: 2BBT5-G3V2), with FCC Part 15.247 regulations. It covers conducted and radiated emissions, bandwidth, output power, and frequency hopping characteristics, performed by Shenzhen NTEK Testing Technology Co., Ltd.
	Machenike G3V2 Wireless Controller FCC Authorization Letter (FCC ID: 2BBT5-G3V2) Official FCC authorization letter from Qingdao Machenike Technology Co., Ltd. designating Shenzhen NTEK Testing Technology Co., Ltd. to act on their behalf for the FCC application of the G3V2 wireless controller, identified by FCC ID 2BBT5-G3V2. Confirms compliance with relevant US regulations.
	MACHENIKE K500-B61 FCC Part 15C Test Report This FCC Part 15C test report details the electromagnetic compatibility testing for the MACHENIKE K500-B61 keyboard, covering conducted emissions, radiated emissions, bandwidth, and antenna requirements. Performed by Shenzhen DL Testing Technology Co., Ltd. for Qingdao Machenike Technology Co.Ltd.
	FCC Part 15C Test Report for MACHENIKE K500-B61 Keyboard This report details the FCC Part 15C compliance testing for the MACHENIKE K500-B61 keyboard, including conducted and radiated emissions, bandwidth, and antenna requirements, performed by Shenzhen DL Testing Technology Co., Ltd.
	Machenike TH60 Headphones Product Label Information Details and specifications for Machenike TH60 headphones, including white color box sticker (3060mm) and outer box sticker (100185mm) information, manufacturer details, FCC ID, and serial number formats.