PowerLogic™ PowerTag M630 3P (LV434022) / 3P+N (LV434023)

Safety and Installation Precautions

⚠️ DANGER: ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices.
• Turn off all power supply sources before installing and during maintenance of this equipment.
• Do not use a PowerTag product for voltage testing purposes. A Voltage Tester must be used instead.
• Replace all devices, doors, and covers before turning on power to this equipment.

Failure to follow these instructions will result in death or serious injury.

⚠️ DANGER: POWERTAG M630 DETERIORATION

• Do not mount PowerTag M630 if the rated network voltage is greater than 480 V~ 50/60 Hz.

Failure to follow these instructions can result in equipment damage.

General Installation Notes:

• PowerTag devices must only be installed and maintained by qualified professionals.
• Do not install if any damage is observed during unpacking.
• PowerTag devices must not be repaired.
• Install PowerTag devices inside electrical panels or switchboards, behind a door or plate, so they are inaccessible to unauthorized persons.
• Ensure electrical panels meet applicable standards (IEC 61439-1) and are installed in compliance with current installation and safety rules (IEC 61140).
• Respect all relevant local, regional, and national regulations.
• Schneider Electric declines responsibility for issues arising from association with unlisted equipment or non-compliance with instructions.

Product Description and Components

The PowerTag M630 is a wireless communication energy sensor designed for use with Schneider Electric circuit breakers like ComPacT NSX and TeSys GV6.

Key Specifications:

• Voltage Range (Un): 3~400 V or 3N~ 230/400 V +/-20%
• Frequency: 50/60 Hz
• Maximum Current (Imax): 630 A
• Basic Current (Ib): 100 A
• Maximum Power Consumption: ≤ 3.7 VA
• RF-Id: FF800000, RN2116100100001

Components:

• A: Status LED: Indicates the operational status of the PowerTag.
• B: QR Code: Access device information. [QR Code]
• C: Disconnect Switch: Used to disconnect the PowerTag supply from the phases, typically for panel dielectric testing.
• D: RF-Id Identifier: Radio Frequency Identification. [RF-Id]
• E: Neutral Voltage Picking: For PowerTag 3P models only.
• F: Detachable Label: Features a QR code and RF-Id identifier for commissioning.

Refer to the selection guide (CA908058E) for compatibility between PowerTag devices and Schneider Electric equipment.

Status LED Indicators

Before pairing, ensure the concentrator has the latest software version. Consult the concentrator's user manual.

Installation and Connection

Mounting: On a fixed circuit breaker (with or without VigiPacT module), the PowerTag M630 must be mounted on the bottom side.

Dimensions:

Refer to the diagrams for specific dimensions for:

• NSX400-630 (3P/4P)
• INS320-630 / INV320-630 (3P/4P)

[Diagram showing dimensions for NSX400-630 (3P/4P) and INS320-630 / INV320-630 (3P/4P) with measurements in mm and inches.]

Connection Steps:

[Diagram showing mounting the PowerTag M630 onto a circuit breaker, including 3P/4P and 3P+N variants.]

[Diagram showing connection points and torque specifications.]

• Mount the PowerTag M630 on the circuit breaker.
• Connect the 3 phases and the neutral to the main device. Consult relevant instruction sheets for specific connection procedures.
• Torque specifications:
  • Main connections: 50±5 N•m (442±44.2 lb-in.)
  • LED/RF connections: 1.2±0.1 N•m (10.5±1.5 lb-in.)
  • Switch: 3±0.3 N•m (26±2.6 lb-in.)

Refer to MFR37601 for installing on a plug-in base.

Dielectric Test Procedure

⚠️ HAZARD OF POWERTAG M630 DETERIORATION

To perform a dielectric test:

1. Turn the dial to the TEST (A) position.
2. After the test, turn the dial back to the RUN (B) position.

Failure to follow these instructions can result in equipment damage.

[Diagram illustrating the dielectric test switch positions (TEST and RUN) and the 3mm clearance.]

Technical Data

Symbols

• [AC symbol] Alternating Current: Indicates AC power.
• [Safety symbol] Safety Compliance: Comply with all safety instructions associated with this symbol to avoid any potential risk of injury or death.
• [WEEE symbol] WEEE Directive 2012/19/EU: Waste Electrical and Electronic Equipment.

Manufacturing Date and Compliance

Manufacturing Date: The product's manufacture date is coded PP-YY-ww-D, where PP: plant code, YY: year, ww: week, D: weekday (Monday=1).

Radio Frequency Compliance Statements:

Schneider Electric Industries SAS declares that the PowerTag is in compliance with essential requirements and relevant provisions of RED Directive 2014/53/EU and UK regulations SI 2017 n°1206.

EU and UK declarations of conformity are available for download at www.se.com/docs.

• RF Band: 2.4 GHz ISM band (2400 MHz to 2483.5 MHz)
• Channels: 11 to 26 (IEEE 802.15.4)
• Max. Transmitted RF Power: ≤ 10 mW (EIRP)

For more information, visit www.se.com.