ThermElc TE-02 PDF Temperature Data Logger User Manual
Brand: ThermElc
Model: TE-02
Product Introduction
The ThermElc TE-02 is designed for monitoring the temperature of sensitive goods during storage and transportation. Once recording is complete, the TE-02 connects to any USB port to automatically generate a PDF report detailing the temperature logging results. No additional software is required to access the data.
Main Features
- ✅ Multiple use logger
- ? Auto PDF report generation
- ? Auto CSV report generation
- Logs up to 32,000 values
- Configurable logging intervals from 10 seconds to 18 hours
- No special device drivers needed
- MKT alarm and Temperature Alarm
Important Note
⚠️ After initial configuration or re-configuration, please leave the device in an open environment for at least 30 minutes. This ensures accurate calibration with the current ambient temperature.
Quick Start Guide
- ⬇️ Download Software: Obtain the free Data Management software to configure the device.
- ▶️ Press and hold the START button for 3 seconds to begin configuration or operation.
- ⏱️ Measure Monitoring: The device will display the current temperature.
- ? Read Report: Connect the logger to a PC via USB to automatically generate PDF and CSV reports.
- ❓ Help: Refer to support resources.
Device Components:
- ?️ LCD Screen
- ? LED Light
- ? USB Interface
- ▶️ Start/Scroll/Mark Button
- ■ Stop Button
Configuration
The TE-02 can be configured using the free Data Management software. Key settings include:
- Time zone: UTC
- Temperature scales: °C / °F
- Screen display: Always on / Timed
- Log interval: 10 seconds to 18 hours
- Start delays: 0 / timed
- Stop mode: Press button / disabled
- Time format: DD/MM/YY or MM/DD/YY
- Start mode: Press button or Timed
- Alarm setting: Upper Limit and Lower Limit
- Description: Custom text to appear on the report.
Operation Functions
-
Start Recording ▶️
Press and hold the PLAY (▶️) button for approximately 3 seconds. The 'OK' light will illuminate, and the (▶️) or (WAIT) indicator will show the logger has started.
-
Mark Data ✎
While recording, press and hold the PLAY (▶️) button for over 3 seconds. The screen will switch to the 'MARK' interface, incrementing the mark count. Each recording interval allows one mark, with a maximum of 6 marks per trip. Mark operation is disabled during start delay.
-
Stop Recording ■
Press and hold the STOP (■) button for over 3 seconds until the 'ALARM' light is on and the STOP (■) symbol appears on the screen. This indicates recording has stopped successfully. If stopped during a start delay, a PDF report will be generated upon PC connection but without data. Short pressing PLAY (▶️) during normal recording cycles through display interfaces: Real-time Temperature > LOG > MARK > Temperature Upper Limit > Temperature Lower Limit.
-
Get Report ?
Connect the logger to a PC via USB. It will automatically generate PDF and CSV files.
LCD Display Instructions
The LCD screen provides status information:
| Display Element | Indicator | Meaning |
|---|---|---|
| Alarm Status | ✔️ / ❌ | Indicates alarm conditions. |
| Log Status | ▶️ | Data logger is recording. |
| Log Status | ■ | Data logger has stopped recording. |
| Mark | ✎ | Indicates data has been marked. |
| Data Value | [Temperature Value] |
Displays the current or logged temperature. |
| Start Delay | ⏳ (WAIT) | Data logger is in Start Delay status. |
| Limits | [Limit Values] |
Displays configured alarm limits. |
| Temperature Scale | °C / °F |
Indicates the selected temperature unit. |
| Battery Status | ? | Indicates battery level. |
| Temperature Exceeds Upper Limit | ⬆️ | Measured temperature exceeds its upper limit. |
| Temperature Exceeds Lower Limit | ⬇️ | Measured temperature exceeds its lower limit. |
Battery Replacement
The TE-02 uses a CR2032 battery.
- 1️⃣ Open the device casing.
- 2️⃣ Replace the CR2032 battery.
- 3️⃣ Close the device casing.
Technical Specifications
Detailed technical specifications are available on the ThermElc website.
