OLMO SIERRA Series Remote Controller Instructions

Important Note

Thank you for purchasing the OLMO air conditioning system. Please read this manual carefully before operating your new unit and save it for future reference.

Remote Controller Overview

General Description

The remote controller transmits signals to the air conditioning system.

Remote Control Buttons and Functions

POWER: Starts or stops the appliance. Pressing this button will start or stop the unit if it is energized or in operation.

TEMP +/-: Used to adjust the room temperature and timer settings, and the real-time clock.

MODE: Press this button to select the operation mode (e.g., COOLING, DRY, FAN ONLY, HEATING).

FAN SPEED: Used to select fan speed in sequence: Auto, Higher, High, Medium, Low, or Lower.

SLEEP: Used to set or cancel Sleep Mode operation.

SWING: Used to stop or start vertical adjustment of the louver for airflow direction (up/down). Also used for horizontal adjustment (left/right) on some models.

CLOCK: Used to set the current time.

TIMER ON / TIMER OFF: Used to set or cancel the timer operation for turning the unit on or off.

QUIET: Used to set or cancel Quiet Mode operation. Pressing for approximately 5 seconds in Cooling or Dry mode (except Super mode) can start Clean mode.

DIMMER: Turns off the remote controller's display light. The light reactivates upon receiving a signal.

ECONOMY: Used to set or cancel Economy Mode operation for energy saving.

IFEEL: Used to set IFEEL mode operation, allowing the remote to sense the room temperature and adjust the unit accordingly.

LOCK: Press and hold [TIMER ON] and [TIMER OFF] buttons together for 2 seconds to lock or unlock the remote. A lock indicator will appear on the display.

SUPER: Used to start or stop fast cooling or heating. The 'SUPER' indicator will display on the LCD.

CLEAN: Initiates a cleaning cycle. The indicator [Clean indicator] will display on the LCD.

SMART: Enters SMART mode for automatic operation adjustments based on room temperature.

46°F HEAT (optional): Used to start or stop the 46°F HEAT mode, setting a minimum heating temperature.

LCD Symbols

• [Cooling indicator]
• [Dry indicator]
• [Fan only indicator]
• [Heating indicator]
• [46°F Heat indicator]
• [Lower fan speed indicator]
• [Auto fan speed indicator]
• [Higher fan speed indicator]
• [High fan speed indicator]
• [Medium fan speed indicator]
• [Low fan speed indicator]
• [Sleep 1 indicator]
• [Sleep 2 indicator]
• [Sleep 3 indicator]
• [Sleep 4 indicator]
• [Lock indicator]
• [Clean indicator]
• [Quiet indicator]
• [Smart indicator]
• [Economy indicator]
• [Super indicator]
• [Ifeel indicator]
• [Power control indicator]
• [Signal transmit indicator]
• [Battery power indicator]
• [Display set timer]
• [Display current time]
• [Display temperature]

How to Use the Remote Controller

Inserting Batteries

1. Remove the battery cover by sliding it in the direction of the arrow.

2. Insert new batteries, ensuring the (+) and (-) terminals match correctly.

3. Reattach the cover by sliding it back into position.

Note: Use 2 LR03 AAA (1.5 volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type when the display dims.

Storage and Tips

The remote controller can be mounted on a wall using a holder (optional part).

Operation

Aim the remote controller at the signal receptor of the indoor unit. Operation is effective up to a distance of 7 meters.

Cautions for Signal Transmission

For optimal signal transmission, keep the signal receiver away from:

• Direct sunlight or other strong lights or heat.
• Flat panel television screens or other electrical appliances that may interfere with the signal.

Ensure curtains, doors, or other materials do not block the signal path between the remote and the indoor unit. If transmission is poor, reposition the unit or consult your dealer.

Operation Modes Explained

Selecting Mode

Press the [MODE] button repeatedly to cycle through modes: COOLING, DRY, FAN ONLY, HEATING. (Note: Heating mode is not available for cooling-only air conditioners.)

FAN Mode

Press the [FAN SPEED] button repeatedly to cycle through speeds: Auto, Higher, High, Medium, Low, Lower. (Note: 'Auto' is not available in 'FAN ONLY' mode. In 'DRY' mode, fan speed is automatically set to 'AUTO' and the [FAN SPEED] button is ineffective.)

Setting Temperature

Use the [TEMP+] button to increase the temperature by 1°F. Use the [TEMP-] button to decrease the temperature by 1°F.

Note: Press and hold the [TEMP+] and [TEMP-] buttons together for 3 seconds to alternate between °C and °F temperature displays.

Note: At 'Dry' mode, temperature can be adjusted by +/- 7°F if needed.

Turning On

Press the [ON/OFF] button. The [RUN indicator] on the indoor unit will light up.

Specific Modes

• SMART Mode: Automatically adjusts operation mode, temperature, and fan speed based on ambient room temperature for optimal comfort. Cancelled by pressing [MODE].
• CLEAN Mode: Initiates a cleaning cycle. Activated by pressing [QUIET] for 5 seconds when in Cooling or Dry mode (standby). An indicator will display. Exits by pressing [ON/OFF], [SMART], or [MODE].
• SUPER Mode: For fast cooling or heating. Displays a 'SUPER' indicator. Can be set when the unit is on or off. Cancelled by pressing [SUPER], [MODE], [FAN], [ON/OFF], [QUIET], or [SLEEP].
• Power Control Mode: Activated by pressing [ECONOMY] for 5 seconds in Cooling mode. Adjusts power consumption in steps (e.g., 75%, 55%, 35%). Cancelled by most other buttons except Swing, Dimmer, IFeel, Clock, Timer, Fan.
• 46°F HEAT Mode: Sets a minimum heating temperature of 46°F. Fan speed is AUTO. Cancelled by most buttons except specific ones.
• TIMER Mode: Allows setting timers for automatic ON or OFF operation.
• QUIET Mode: Operates with low noise. Cancelled by various mode buttons.
• ECONOMY Mode: For energy saving. Ineffective in SMART, SUPER, and Power Control modes.
• IFEEL Mode: The remote controller senses room temperature and adjusts the unit accordingly. Activated by pressing [IFEEL].
• DIMMER Button: Turns off the remote's display light. The light turns back on when a signal is received.
• LOCK Mode: Press and hold [TIMER ON] and [TIMER OFF] for 2 seconds to lock/unlock the remote. A lock indicator appears.
• SLEEP Mode: Provides a comfortable sleep environment. Automatically stops operation after 8 hours. Fan speed is set to low. Offers multiple sleep curves (SLEEP 1-4) that adjust temperature over time. Cancelled by various mode buttons or holding [ECONOMY] for 5 seconds.
• HI-NANO Mode: Activated by pressing [QUIET] and [DIMMER] together for 3 seconds.

Limited Warranty Information

This Limited Warranty is provided by Comfortside, LLC and applies only to registered products installed by a licensed HVAC technician.

Warranty Coverage

The warranty covers parts defective due to materials or workmanship under normal use and proper maintenance. It is valid only for the first original owner at the installation site and is non-transferable.

Product Registration

Products must be registered within 60 days of installation by a licensed HVAC technician. Registration can be completed online at www.olmo-comfort.com or by mail using the provided warranty card.

Warranty Exclusions

Comfortside is not responsible for claims arising from:

• Installation outside North America or not according to manufacturer guidelines.
• Relocation after initial installation.
• Invalid registration information.
• Faulty installation, inappropriate application, or improper use.
• External perils (acts of nature, fires, storms, accidents, floods, electrical surges, corrosive substances).
• Use of non-compatible parts, third-party components, alterations, or modifications.
• Improper service or poor maintenance (e.g., filter cleaning, lubrication).
• Cosmetic changes (e.g., minor scratches).
• Issues related to power resets, circuit breakers, or fuse replacements.
• Damage from incorrect refrigerants or lubricants.
• Damage due to moisture, dust, sand, or dirt.
• Continued use after a malfunction is indicated.
• Improper matching, selection, installation, or misuse.
• Loss or replacement of refrigerant or lubricant.
• Labor costs or costs associated with labor.
• Claims related to refrigerant loss discovered upon arrival or during installation, or subsequent loss.

Warranty Procedure

Contact Comfortside Technical Support at (786) 953-6706 (Monday-Friday, 9 AM-5 PM Eastern Time) with a licensed technician onsite. Provide the unit's serial number, purchase invoice, and installation invoice. Comfortside may request photos or diagnostic information.

Note: The owner is responsible for labor costs, materials, shipping, and refrigerant costs.

Governing Law and Arbitration

This warranty is governed by the Federal Arbitration Act. Disputes will be settled by binding arbitration on an individual basis. Arbitration hearings are typically conducted in Miami-Dade County, Florida. The terms and conditions of this warranty agreement cannot be altered by any other party.