QCY-T8 TWS Smart Earbuds User Manual
Brand: QCY
Overview
Diagram of the QCY-T8 TWS Smart Earbuds and charging case. The earbud features an 'In-ear sensor', 'Touch panel', 'Tuning hole', and an 'LED' indicator. The charging case includes an 'LED' indicator, a 'Charging case button', and a 'Type-C USB charging port'.
For better using experience, please scan to download QCY app before start-up.
How to Connect
First-time connectivity
Turn off phone's Bluetooth. Earbuds will auto power on, pair with each other, and turn connectable. On phone, search for QCY-T8 and tap to connect both earbuds to phone.
Switch connected device
1. Turn off phone's Bluetooth. 2. On phone B, search for QCY-T8 and tap to connect. Multi-point connection is not available, and earbuds will auto reconnect to phone upon powering up again.
Factory Setting
To resolve connectivity errors, follow these methods:
Method 1: Delete connectivity record on phone if any. Take out both earbuds from case and keep touching both panels for 5s or until LED glows red for 2s to power off them. Then, open the lid and keep touching both panels for 10s or until LED blinks red and blue 3 times to reset to factory. Earbuds will then auto power on and pair with each other. Refer to 'How to Connect' for re-establishing connection after Factory Setting.
Method 2: Open the charging case lid and long press the charging case button for 10s or until the LED blinks red and blue 3 times, then close the lid to reset earbuds to factory.
How to Wear
Rotate earbud and pop it into your ear. Then shake head to check wearing stability. Adjust mic towards your mouth for better calling experience. Please wear earbuds properly, making sure they fit snugly and sound holes are inside ear channels. You may turn on 'In-ear Detection' in the QCY APP.
One Press to Enter Pairing Mode
When earbuds have been connected to phone: Pop earbuds into case. Open lid and hold charging case button for 5s or until LED on case blinks green 3 times. Earbuds will then disconnect to phone and enter pairing mode.
Mono Mode
If earbuds were paired before: Keep touching the panel on either earbud for 5s to power them on. They will auto turn connectable (LED will blink blue). On phone, search for QCY-T8 and tap to connect the earbud to phone.
Charging
Charge the Earbuds
Push earbuds into the case and close the lid. Earbuds will auto turn off and be charged.
Charge the Case
Connect a Type-C USB cable to the charging port. The LED of the case will glow solid red when charging and turn green once topped up.
Parameters
| Parameter | Value |
|---|---|
| Model | TWS Smart Earbuds |
| Pairing name | IN2004A |
| Bluetooth version | V5.0 ? |
| Talk time | approx. 3.5hr |
| Music time | approx. 3.5hr |
| Operation range | 10m (with no obstacle) |
| Battery type | Li-ion ? |
| Battery capacity (earbud) | 3.7V 35mAh |
| Battery capacity (case) | 3.7V 380mAh |
| Input parameter (case) | 5V 450mA |
| Bluetooth profiles | HSP/HFP/A2DP/AVRCP ? |
Functions
| Functions | Current status | Operation | LED | Voice Prompt |
|---|---|---|---|---|
| Power-on | Earbuds are not in the case | Keep touching the panel for 2s | LED blinks blue | TONE |
| Earbuds are in the case with its lid closed (the case is within power) | Open the lid | LED glows solid red when charging | - | |
| Power-off | Case is within power | Push earbuds into case and close the lid | LED glows red for 2s | TONE |
| Answer/end call | Incoming call/ calling | Double tap the panel to answer/end the call | - | TONE |
| Ignore call | Incoming call | Keep touching the panel for 1s | - | TONE |
| Voice assistant | Connected | Triple tap the panel | - | TONE |
| Music pause/resume playing | Playing | 1. Double tap 2. Put off either earbud to pause and put it on in 15s to resume playing | - | - |
| Skip track forward | Playing | Keep touching either panel for 2s to skip track forward | - | - |
Warranty Card
Warranty Period: 12 months after you purchase this item (or you may consult the local shopper for more details).
Free Service: Supposing any defects caused by quality issues occur during the warranty period, please keep this warranty card and purchase receipts to your distributor for free exchange service.
Model Number:
Date of Purchasing:
User's Name:
User's Address:
Shop's Name:
Shop's Address:
Comments:
Free exchange service will not be accessed under following circumstances:
- Earbuds have been misused/authorized disassembly.
- Defects or physical damages caused by leaking or dropping off.
- Force majeure act of God. Supposing your item is within any damages or defects the above-free circumstances, please return to your or distributor for free repairing.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Hazardous Substances and their contents in the item
| Part Name | Pb | Hg | Cd | Cr(VI) | PBB | PBDE | DBP | DEHP | DIBP | BBP | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Housing | O | O | O | O | O | O | O | O | O | O | O | O |
| PCB | O | O | O | O | O | O | O | O | O | O | O | O |
| Battery | O | O | O | O | O | O | O | O | O | O | O | O |
| Ear tip | O | O | O | O | O | O | O | O | O | O | O | O |
| Accessories | O | O | O | O | O | O | O | O | O | O | O | O |
| Cable | X | O | O | O | O | O | O | O | O | O | O | O |
This form is made by SJ/T 11364 regulation.
O: means the hazardous substance content in the homogeneous material of this part is within the limits of (EU) 2015/863 regulation.
X: means that the hazardous substance content of at least one of the homogeneous material of this part is beyond the limits of (EU) 2015/863 regulation, but there is no feasible alternative in the industry, at present, it still conforms to the EU RoHS restricted use of exemption.
RoHS directive 10: [RoHS directive 10]
Tips
1. Before using the headset, please read the manual carefully and set aside for future references.
2. If the headset need to be fully charged prior to first time use: If the headset is left unused for over two weeks, please recharge it periodically.
3. Please use the chargers made by qualified manufacturer.
4. If headset cannot be found by your phone, please check whether it is paired with any current device for a long while, the headset will exit pairing mode, please re-enter the mode. If a procedure error of your phone occurs, reboot it. If a procedure error of the headset occurs, reboot it.
5. Keep the headset dry.
Caveats
1. Never disassemble or modify your headset for any reasons to avoid any damages and danger.
2. Do not use the headset in extreme temperatures (under 0°C or over 45°C).
3. Avoid using the indicator close to the eyes of children or infants.
4. Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electric shock.
5. Do not use chemical solvents or strong detergents to clean the headset.
6. Keep the headset dry.
