Sonoff Dual R3 Smart Switch and Motor Controller Installation Guide
Introduction and Safety
Attention: AC voltage is very dangerous. Get help from an electrician to connect AC voltage wires to the Sonoff device. When you power up the device, it will broadcast a "HomeHome-XXXXXX" WiFi network with the password "homehome".
Note: The device LED will NOT blink when it gets power. After setup is finished, the LED will be visible.
If you need help, please do not hesitate to contact ➡️ Sonoff support.
IMPORTANT Instructions for Motor Control
FULLY CLOSE THE ROLLER SHUTTER. Use L1 OUT for MOTOR UP. Use L2 OUT for MOTOR DOWN.
SET OPEN CLOSE TIME IN SECONDS: Count the seconds required for fully open and close operations, then set this time in the LOCAL HTTP SERVER.
You can find more settings under the local HTTP server after WiFi setup.
For motor type: http://motor-XXXXXX.local
For on-off type: http://hh-xxxxxx.local or http://device_ip_address
WiFi Setup
You will see a captive portal for device setup. If it doesn't start automatically, disconnect from WiFi, unplug-plug the device, and reconnect to WiFi.
- Connect to the "HomeHome-XXXXXX" WiFi network. Password: "homehome".
- Select device type: Sonoff Dual R3 On-Off or Sonoff Dual R3 Motor Control (Roller Shutter/Blind). Fully close your Shutter/Blind. The standard open-close time is 10 seconds; adjust this after WiFi setup.
- Enter your GMAIL address which you use in your Android Phone. You can just write your name if you will not use Google Home or smart.homehome.app.
- Select your Home WiFi and enter its password. Ensure you enter the correct password, or it will not connect to your network.
Q: What happens when my router is off?
A: The device will try to connect for a few minutes and then begin broadcasting its own network (HomeHome-XXXXXX).
Save settings and start the Apple HomeKit application to add the accessory.
Apple HomeKit Setup
Pair code is 1118-8111. Select your room and a name for your device.
Google Home Setup (Optional)
- Open the Google Home app from your Android phone.
- Tap
+> Set up device > Works with Google >+HomeHome> Login.
Important: For using Google Home, please write your Gmail address and device ID (XXXXXX) to info@homehome.app, which is required for activating your device.
Ensure your Gmail address is the same across your "Android phone account", "+HomeHome login account", "Device setup" (step 3), and "WEB UI Setup" (step 9).
WEB UI Setup (Optional)
Access via: https://smart.homehome.app
You must register your device. Sign in with the same Gmail account. Click the "Manage" tab and activate the Device ID: XXXXXX. Unplug-plug or restart the device from the HTTP server.
HTTP Server
Q: Where to find the IP address?
- Long press the accessory in the HomeKit app and see the device's IP.
- You can also find XXXXXX (MAC address) in your router's DHCP list.
Enter the Device IP address to set:
- ✔️ Auto off timer for switch (1 second to 24 hours)
- ✔️ Open-close time for motor control
Extra Features
- ✔️ You can control your device with "Hey Siri", "OK Google".
- ✔️ Make Scenes or Routines for full automation.
- ✔️ You can update firmware under the local HTTP server.
- ✔️ "Local Mode": Set device to work offline (without internet). If local mode is enabled, you cannot use Google Home and the Web interface (smart.homehome.app). You must first register the device (with internet connection) to use this feature.
Wiring Diagrams
On Off Control (2 Way Example)
This diagram illustrates the wiring for the Sonoff Dual R3 in an "On Off Control" configuration, suitable for a 2-way switching setup. It shows two switches connected to the device. The inputs are labeled "N In" (Neutral Input) and "L In" (Live Input). The outputs are labeled "L Out 1" and "L Out 2", each intended to control a separate load, such as a light. The diagram indicates that the two switches can independently control the two output relays.
Motor Control
This diagram depicts the wiring for the Sonoff Dual R3 configured for "Motor Control", ideal for devices like roller shutters or blinds. It includes two switches connected to the device. Inputs are "N In" and "L In". The outputs are labeled "L1" and "L2", which connect to the motor terminals (labeled "M"). This setup allows for controlling the motor's direction, enabling operations like opening and closing a shutter.
A second, identical diagram for Motor Control is provided for reinforcement.
Resources
Download PDF: https://homehome.app/manuals/
Translate: https://translate.google.com
For more help: info@homehome.app
Version: 1.23
