Smart Pet Feeder User Manual

Components

• 1. Food Hopper
• 2. Main Body
• 3. Top Lid
• 4. Food Bowl
• 5. Type-C Adapter
• 6. Desiccant
• 7. Manual
• 8. Stainless Steel Bowl

Features

Exploded view of the Smart Pet Feeder:

• Top Lid (with Silicone seal and Desiccant Box)
• Food Hopper
• Rotation Box
• Impeller
• Camera Cover
• Camera
• Stainless Steel Bowl
• Food Bowl
• Feeding Slice
• Body
• Food Outlet

Product Introduction

Setup and Assemble Feeder

Install Food Hopper

Take out the food hopper and install it by aligning the slot on the base.

Place Desiccant

Open the desiccant box on the top lid, tear off the transparent wrapping paper of the desiccant bag, place it into the box, and close it.

Plug in Power Adapter

1. Battery power supply (APP Not Work): Insert 4 alkaline “D” batteries and reinstall the battery cover.
2. Power adapter supply: Plug in the power adapter and connect the power cable into the card slot.

Note: Please use safe and standard alkaline batteries. Do not mix batteries of different specifications and models.

Install the Food Bowl

Tilt the base unit back slightly, align the buckle of the food bowl with the base unit to install. The steps to disassemble are the same.

Fill Pet Food

Open the top lid, fill fresh dry food into the food hopper, and close the top lid.

Note: The device only supports 5-15mm dry pet food.

Product Introduction (App Access)

Get Access to App

1. Scan the QR code to download the APP.
2. Please login or register an account.
3. Turn on the Bluetooth, click "+" on the top right in the Home page and add the device following the instruction.

Note: WIFI 2.4&5GHz and BLE are allowed to use.

Set Up Your Programmed Feeding

The pet feeder will dispense food based on the programmed feeding, and users can receive feeding notifications accordingly.

Reset Your Pet Feeder

Long press the SET button for 10 seconds to reset your feeder until you hear a "Di" sound. The Orange Link indicator will flash rapidly, and you can then try to connect your pet feeder again. You can use tools like card pins to complete this step.

APP Remote Feeding

Enter the device setting page and click "Feeding", select servings, and click "Feed" to complete the remote feeding.

Note: Users cannot feed their pets via APP when powered by batteries.

Instant Feeding

Short press the FEED button twice, then the device will dispense one serving. Repeat the above step for more servings.

Operation Features

The device features a SET button, a FEED button, and a MIC (microphone) indicator.

Indicator State

Device Disassemble & Clean

Power Off

Unplug the device and take out the alkaline batteries.

Clean the Food Hopper

1. To disassemble, hold both sides of the food hopper and rotate to the left and lift upwards.
2. Disassemble the impeller, feeding slice, and feeding mechanism.
3. The main body of the feeder is not dishwasher-safe.
4. The food bowl is dishwasher-safe once removed from the main body.

Assemble the Impeller

1. Align the impeller with the correct position and install it at an inclined angle.
2. Align the impeller as shown in the figure: one diagram shows a correct alignment (indicated by a green checkmark ✔️), and the other shows an incorrect alignment (indicated by a red cross ❌).

Maintenance

Clean the Food Bowl

Make sure all parts of the feeder are completely clean and dry before filling with food.

Clean the Body

Use a dry soft cloth to wipe it. The body is not waterproof; please do not use a wet cloth.

Replace the Desiccant Pack

Open the desiccant box cover and replace the desiccant pack. It is suggested to replace it every one or two months.

Replace Alkaline Batteries

Unplug and open the battery lid at the bottom, then you can replace the batteries.

Replace or Change the Food

Empty the food hopper, then fill with fresh food and proceed with instant feeding once.

Attention Points

• Please keep the food hopper dry after cleaning it.
• Please replace the food on a regular basis if your pets did not eat up. (For time period, please refer to the food packing instruction).
• Please clean and maintain your device on a regular basis to prolong the using period of your pet feeder.

Safety Precaution

Keep Plug In

1. Please check the power supply of the device before going out to ensure that the power supply is stable.
2. Please keep charging the device to make sure the WiFi connection is stable.
3. The camera will turn off automatically to enter lower power consumption mode when using dry batteries, but your feeding plan will continue to work.
4. There will be no record of the feeding status and records if the device is offline.

Working Conditions

1. Place the device horizontally and securely. Tilting, swaying, or turning upside down are forbidden.
2. Exposure to sunlight could damage the internal electronics or cause discoloration. Do not place or store the appliance where it can fall or be pulled.
3. Do not remove product components other than the food bowl and hopper.
4. Do not place any foreign object in the pet feeder.
5. Please make sure there are no objects on and around the food bowl to prevent pets from eating normally.

Important Safety Information

• This product is only applicable to cats and small dogs.
• Do not allow children to play with, in, or around the pet feeder.
• The desiccant is not edible. If it is damaged, do not use it.
• The feeder is only applicable for 5-15mm dry pet food.
• Do not disassemble the pet feeder other than components as instructed in this operating guide.
• Do not immerse the feeder in water, as this may damage electronic components.
• The feeder only supports charging with a 5V/2A adapter.
• Do not allow pets to chew on or swallow any parts.
• Do not use the pet feeder for any purpose other than feeding pets.
• Do not touch the camera to avoid scratches and oil stains.

FAQ

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.