SONOFF TX Ultimate Smart Touch Wall Switch

Introduction

SONOFF TX Ultimate is a smart touch wall switch with LED lights which will produce sound, light, and vibration effects when it is turned on/off. After adding in the eWeLink App, you can remote control on/off, switch the ambient lighting modes, set timer, and smart scene on the phone.

Features

Device Overview

The SONOFF TX Ultimate Smart Touch Wall Switch features:

• 1: Switch panel: The primary touch-sensitive surface for control.
• 2: Touch control screen: Integrated touch interface on the panel.
• 3: Ambient light/Switches LED indicator/Network LED indicator: LED indicators for status and ambient lighting.
• 4: Wiring ports: Terminal blocks on the back for electrical connections.

LED Indicator Status and Instructions

Operation Instruction

1. Horizontal installation

The switch can be operated using the following touch gestures:

• Quick click: A single, brief tap on the switch panel.
• Long press: Pressing and holding the switch panel for approximately 5 seconds.
• Swipe: Moving a finger across the switch panel horizontally or vertically.
• Multi-point click: Using multiple fingers to tap the switch panel.

2. Vertical installation

The same touch gestures apply for vertical installation.

Operations Summary

Specifications

Installation

1. Power off

Before installation, ensure the power supply is turned off at the main circuit breaker. The diagram shows a circuit breaker panel with switches in the ON and OFF positions, and a hand turning one switch to OFF.

2. Wiring instruction

Switch mode

Wiring diagrams are provided for different models (1C, 2C, 3C, 4C) showing connections for a 100-240V AC power source (Live 'L' and Neutral 'N').

• 1C Model: Live and Neutral wires connect to the switch's input. One output terminal (L1) connects to a single light.
• 2C Model: Live and Neutral wires connect to the switch's input. Two output terminals (L1, L2) connect to two lights.
• 3C Model: Live and Neutral wires connect to the switch's input. Three output terminals (L1, L2, L3) connect to three lights.
• 4C Model: Live and Neutral wires connect to the switch's input. Four output terminals (L1, L2, L3, L4) connect to four lights.

Note: Red wires typically represent Live and output connections, while blue wires represent Neutral.

Safety Precaution

*Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

Motor mode wiring

For motor control (T5-3C-120 model only), the wiring involves connecting the motor's forward and reverse lines to specific channels (e.g., channel one for positive rotation/opening, channel three for reverse rotation/closing), along with Live (L), Neutral (N), and a ground wire. The diagram shows a motor labeled 'M' with 'Forward' and 'Reverse' connections.

*To ensure the safety of your electrical installation, it's essential to have a Miniature Circuit Breaker (MCB) or a Residual Current operated Circuit-breaker with Integral Overcurrent protection (RCBO) installed with an appropriate electrical rating (10A for T5-1C/2C-120, 16A for T5-3C/4C-120) before installing the TX Ultimate. (This does not include motor load).

*Make sure all wires are connected correctly.

3. Power on

After powering on, the device will enter Bluetooth pairing mode by default during the first use, and the LED frame light will illuminate in "Cycle mode."

*The device will exit Bluetooth pairing mode if not paired successfully within 30 minutes. To re-enter pairing mode, touch the wall switch panel for 5 seconds until the LED frame light enters "Cycle mode."

Add Device (eWeLink App Pairing)

1. Download the "eWeLink" App

Please download the "eWeLink" App from the Google Play Store or Apple App Store.

2. Add device steps

1. On your smartphone, open the eWeLink app and navigate to the "My Home" screen. Tap the "Add Device" button.
2. Select the "Scan" option.
3. Scan the QR code located on the device.
4. Follow the wiring instructions to connect the wires. Ensure power is disconnected before wiring and consult an electrician if needed.
5. Power on the device.
6. Long press the button (on the switch panel) for 5 seconds.
7. Check the Wi-Fi LED indicator flashing status (should be in "Cycle mode").
8. In the app, select "Add Device" or "Scan" to search for the device.
9. Select your "Wi-Fi" network and enter the password.
10. The device will be added successfully.

The app interface illustrations show these steps, including scanning, wiring, powering on, long-pressing, checking LED status, searching for the device, selecting Wi-Fi, and a confirmation of successful addition.

Motor Mode Configuration

After wiring for Motor mode, you can switch the Working Mode to "Motor mode" within the eWeLink App to make traditional motors smart and controllable via smartphones, smart scenes, and voice commands.

1. Applicable load:

• Can control bidirectional AC motors, such as roller shutters, blinds, curtains, and awnings.
• Only supports motors with limited position functions.
• Maximum motor load current: 1A.

2. Working methods:

• Connect the positive rotation line to channel one to control positive rotation/opening.
• Connect the reverse rotation line to channel three to control reverse rotation/closing.

3. App settings:

After adding the device, switch the Working mode to Motor mode following these steps:

1. On the device's homepage in the eWeLink app, tap the "..." icon.
2. Navigate to "Device Settings" and select "eWeLink-Remote sub-devices".
3. Tap the "Add" button. The eWeLink-Remote gateway will enter learning mode.
4. Click the sub-device button within 10 seconds.
5. Click the button on the sub-device to add it.

The app screenshots illustrate selecting "Working Mode" from Device Settings and then choosing "Motor mode". Another set of screenshots shows the process of adding eWeLink-Remote sub-devices.

Device Factory Reset

• After "Delete the Device" in the eWeLink App.
• For devices previously successfully added to eWeLink, perform a new pairing using a different eWeLink account.

Compliance Information

FCC Compliance Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1) This device may not cause interference.
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003(B). This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

ISED Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

(French translation of ISED Notice and Radiation Exposure Statement is also present in the original document but merged into English here for primary language consistency).

SAR Warning

Under normal use conditions, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

(French translation of SAR Warning is also present).

Environmental and Declaration Information

WEEE Warning

♻️ [WEEE symbol] WEEE Disposal and Recycling Information: All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd declares that the radio equipment type [T5-1C-120, T5-2C-120, T5-3C-120, T5-4C-120] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/

Packaging details:

• Scatola (Box): PAP 20
• Manuale (Manual): PAP 22
• Pellicola (Film): PET 1
• Borsa (Bag): LDPE 4
• Carta (Paper): Carta
• Plastica (Plastic): Plastica

RACCOLTA DIFFERENZIATA (Separate waste collection): Verifica le disposizioni del tuo Comune. Separa le componenti e conferiscile in modo corretto. (Check your municipality's regulations. Separate components and dispose of them correctly.)

Technical Details

EU Operation frequency Range:

• Wi-Fi: 802.11 b/g/n20: 2412-2472MHz; 802.11 n40: 2422-2462MHz
• BLE: 2402-2480MHz

EU Output Power:

• Wi-Fi 2.4G: <20dBm
• BLE: ≤10dBm

Manufacturer Information

Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.

Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China

ZIP code: 518000

Website: sonoff.tech

Service email: support@itead.cc

Made in China

Certifications: ✔️ [CE mark], ✔️ [FCC mark], Recycling symbols.