iTech Fusion 2 Smartwatch

Quick Start Guide

Step 1: Charging Your Smartwatch

Your smartwatch may be in low battery mode when you first receive it. We recommend charging your smartwatch fully before first use. Battery life and charge cycles vary based on usage.

• Plug the charging cable into the USB port on your computer or a UL-certified USB wall charger.
• Connect the smartwatch to the charging cable. A charging screen appears on the watch to indicate that your smartwatch is charging.

Your smartwatch takes about 1-2 hours to fully charge.

Step 2: Set Up Your Smartwatch

To set up your new smartwatch, download the free mobile app by scanning the QR code provided in the original documentation. Open the app on your phone, tap the watch icon on the upper right, and follow the pairing instructions. Once finished, the correct time and date will appear on your watch.

NOTE: Pairing must be done using the mobile app and not with your phone's native Bluetooth.

Replacing or Changing the Watch Band

To remove the existing strap:

• Turn the watch face down.
• With your finger, pull the pin to the left and gently pull the band away from the watch. The band should easily detach from the watch.

Attaching a new band:

• Line up the steady pin with the hole on the base of the case.
• While carefully holding the band in place, pull the lever on the band to retract the pin and position the band against the case to line up the pin.
• Release the lever so the pin snaps into place.
• Repeat these steps for the other strap.

Safety and Skin Care

To ensure maximum comfort and prolong the life of your device:

• Regularly clean your smartwatch with a damp cloth.
• After cleaning, always dry your watch thoroughly.
• Keep your wrist free of any cosmetics, dirt, and oils.
• Keep your watch loose enough to allow some air circulation (wearing a watch too tightly can cause skin irritation).
• After workouts, we strongly suggest cleaning both the watch and your wrist.
• Should you experience any skin irritation, discontinue wearing for at least several days or until the irritation subsides.
• Adults with eczema or any skin condition should consult a physician before wearing the watch.

NOTE: Failure to follow the safety and skin care instructions may affect certain warranty claims.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Warning Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Warranty

This limited warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

For all warranty information please visit: www.itechwearables.com/warranty

ROUND FCC ID: 2AS3PITFRD21

SQUARE FCC ID: 2AS3PITFSQ21

System Requirements

• Android 9.0 and up
• iOS 13.0 and up

Make sure your phone's Bluetooth is turned on and enabled.

For user manuals, please visit support.itechwearables.com

Support

For technical assistance, warranty, and customer service, email: support@itechwearables.com

Or visit us at: support.itechwearables.com