Makita HK0500 Spare Parts List and Service Drawing
Spare Parts List
Model No. HK0500
| ITEM | PART NO. | DESCRIPTION | QTY | NOTE |
|---|---|---|---|---|
| 001 | 286265-0 | Dust cap* | 1 | |
| 002 | 416729-2 | Drill chuck cover HK0500 | 1 | |
| 003 | 233203-3 | Compression spring 38, red | 1 | |
| 004 | 344691-0 | Spring guide sleeve HK0500 | 1 | |
| 005 | 232192-9 | Leaf spring 26 HK0500* | 1 | |
| 006 | 323724-4 | Drill chuck ring HR2400/160D/ | 1 | |
| 007 | 256447-8 | Pin 8, rotating assembly | 1 | |
| 008 | 344691-0 | Spring guide sleeve HK0500 | 1 | |
| 009 | 233238-4 | Compression spring 38 HK0500 | 1 | |
| 010 | 416733-1 | Adjusting ring HK0500* | 1 | |
| 011 | 962156-6 | Seeger ring R-38 962156-6 | 1 | |
| 012 | 257218-6 | Ring 27 HK0500 | 1 | |
| 013 | 261113-4 | Polyurethane washer 28 HK0500 | 1 | |
| 014 | 257218-6 | Ring 27 HK0500 | 1 | |
| 015 | 213433-2 | Oil seal 30 HK0500 | 1 | |
| 016 | 265995-6 | Self-tapping screw M4x18* | 2 | |
| 017 | 416734-9 | Crankcase cover HK0500 | 1 | |
| 018 | 216022-2 | Steel ball 7.0, rotating assembly | 1 | |
| 019 | 324063-5 | Tool holder | 1 | |
| 020 | 213173-2 | X-ring 13 HK0500* | 1 | |
| 021 | 213214-4 | O-ring 16 213214-4* | 1 | |
| 022 | 324012-2 | Punch pin | 1 | |
| 023 | 267192-0 | Flat washer 13 HK0500* | 1 | |
| 024 | 213175-8 | O-ring 14 HK0500 | 1 | |
| 025 | 213117-2 | O-ring 11 HR2410/HR2010/HK050 | 1 | |
| 026 | 323846-0 | O-ring retainer HK0500 | 1 | |
| 027 | 231987-7 | Coil spring 21 HK0500 | 1 | |
| 028 | 323848-6 | Piston HK0500 | 1 | |
| 029 | 213227-5 | O-ring 16 HK0500* | 1 | |
| 030 | 213227-5 | O-ring 16 HK0500* | 1 | |
| 031 | 256123-4 | Pin 5 HR1800/HR2010/HK050 | 1 | |
| 032 | 416726-8 | Piston HK0500 | 1 | |
| 033 | 267129-7 | Flat washer 27 HR2410/KH0500 | 1 | |
| 034 | 213560-5 | O-ring 44 HK0500* | 1 | |
| 035 | 266034-5 | Self-tapping screw M4x16* | 1 | |
| 036 | 416732-3 | Crankcase cover HK0500 | 1 | |
| 037 | 213656-2 | O-ring 53 HM1200/HR5000 | 1 | |
| 038 | 416727-6 | Connecting rod HK0500 | 1 | |
| 039 | 323826-6 | Crankshaft HK0500 | 1 | |
| 040 | 962151-6 | Seeger ring R-32 962151-6* | 1 | |
| 041 | 211232-6 | Ball bearing 6002LLU HK0500 | 1 | |
| 042 | 151543-6 | Crankcase assembly, complete HK0500 | 1 | |
| 043 | 266021-4 | Self-tapping screw M5x20 | 1 | |
| 044 | 213219-4 | Oil seal 15 HK1800/HK0500 | 1 | |
| 045 | 226779-7 | Gear 41 HK0500 | 1 | |
| 046 | 211066-7 | Ball bearing 6200LLB 211066-7 | 1 | |
| 047 | 213663-5 | O-ring 55 HR5000 (HK0500 new) | 1 | |
| 048 | 151579-5 | Gear cover assembly, complete | 1 | |
| 049 | 266034-5 | Self-tapping screw M4x16* | 4 | |
| 050 | 961052-5 | Seeger ring S-12 961052-5 | 1 | |
| 051 | 211129-9 | Ball bearing 6201DDW 211129-9 | 1 | |
| 052 | 253069-5 | Flat washer 12 253069-5 | 1 | |
| 053 | 285690-2 | Bearing cover 68 HK0500 | 1 | |
| 054 | 251304-5 | Flat head screw M4x12 | 2 | |
| 055 | 518626-9 | Armature 220V HK0500 | 1 | |
| INC. 57,59 | ||||
| 056 | 416730-7 | Air duct plate HK0500 | 1 | |
| 057 | 681644-1 | Insulated washer 681644-1 | 1 | |
| 058 | 266211-9 | Self-tapping screw M5x40 | 2 | |
| 059 | 210005-4 | Ball bearing 608DDW 210005-4* | 1 | |
| 060 | 594319-2 | Stator 220V HK0500 | 1 | |
| 061 | 819063-3 | MAKITA label* | 1 | |
| 062 | 643605-9 | Carbon brush holder CB-116/CB-113 | 2 | |
| 063 | 191904-8 | Carbon brush CB-113 191904-8 | 1 | |
| 064 | 416736-5 | Motor housing HK0500 | 1 | |
| 065 | 851374-0 | Nameplate HK0500 | 1 | |
| 066 | 631291-8 | Control electronics 220-240 | 1 | |
| 067 | 423308-9 | Foam rubber sheet 13-33 HK0500 | 1 | |
| 068 | 416728-4 | Switch lever HK0500 | 1 | |
| 069 | 651969-7 | Switch HK0500 | 1 | |
| 070 | 645200-1 | Noise filter capacitor 645200-1* | 1 | |
| 071 | 151544-4 | Handle cover assembly, complete HK0 | 1 | |
| 072 | 265995-6 | Self-tapping screw M4x18* | 6 | |
| 073 | 265995-6 | Self-tapping screw M4x18* | 2 | |
| 074 | 687052-4 | Cable strain relief 6870 | 1 | |
| 075 | 665883-1 | POWER SUPPLY CORD 1.0-2-5.0 | 1 | |
| 076 | 682540-6 | Cable protector 9.3-90 682540-6* | 1 | |
| 077 | 231979-6 | Spring ring 17, forked fitting | 1 | |
| A01 | A-30483 | SCALING CHISEL 37x200 | 1 | |
| A02 | 824523-2 | PLASTIC CARRYING CASE | 1 | |
| E01 | 652257-5 | Clamping piece 652257-5, new+F278 | 2 | |
| E02 | 654532-5 | Terminal block 1P 654532-5* | 1 | |
| E05 | 646047-6 | CHOKE COIL | 1 | |
| E06 | 539147-8 | CHOKE COIL ASS'Y | 1 | |
| E07 | 654002-4 | Carbon brush holder | 2 | |
| E08 | 654077-3 | INSULATED TERMINAL FK2-M3D-5.5 | 1 | Y04979 |
| E17 | 646048-4 | CHOKE COIL | 1 |
Service Drawing
Model No. HK0500
Diagram of Components
The service drawing illustrates the internal and external components of the Makita HK0500. The diagram shows numbered parts corresponding to the spare parts list. Key components include the motor housing, crankshaft, gears, switches, and various springs, seals, and fasteners, arranged to show the assembly of the tool.
Key numbered components visible in the drawing:
- 1-15: Various rings, seals, and bearings related to the drive mechanism.
- 16-34: Components of the hammering and rotation mechanism, including the crankshaft, piston, gears, and associated springs and seals.
- 35-49: Parts related to the gear housing and drive assembly, such as gears, bearings, and covers.
- 50-61: Components of the tool holder and chuck mechanism.
- 62-76: Electrical and housing components, including switches, carbon brush holders, motor housing parts, and fasteners.
