Makita 9558HNRG Angle Grinder
Parts List and Exploded View Diagram
Exploded View Diagram Overview
The document presents an exploded view diagram of the Makita 9558HNRG angle grinder. This detailed illustration shows how the various components are assembled. Starting from the motor end, the diagram depicts the armature (6) within the motor housing (50), connected to the gear mechanism. The gear housing (18) contains gears (11, 23), bearings (4, 10, 25), and a spindle (32). Various covers (8, 13, 54), seals (3, 9, 27, 30), washers (22, 26), retaining rings (21, 24), and screws (15, 29, 33, 37, 39, 45, 55) are used to secure these parts. The tool also includes a switch assembly (43, 53), carbon brush holders (40, 51) with brushes (41), a power cord (48), and a disc guard (34) with mounting flange (35) and nut (36). A nameplate (38) is also shown.
Parts List
| Part Number | Catalog Number | Part Name |
|---|---|---|
| 1 | 621708-9 | Stand / Field Coil for 9557/58NB |
| 2 | 418770-1 | Diffuser for 9557/8NB |
| 3 | 421868-5 | Rubber Gasket 19 for 9554/55NB |
| 4 | 210034-7 | Ball Bearing 607LLB |
| 5 | 681636-0 | Ring |
| 6 | 515613-9 | Armature for 9557/8NB |
| 8 | 317821-6 | Gear Housing Cover for 9554-58NB |
| 9 | 213445-5 | O-ring |
| 10 | 210042-8 | Ball Bearing 629LLB |
| 11 | 227541-3 | Gear Wheel 10 for 9554-58NB |
| 12 | 252186-8 | Nut M6 for 9555-58NB |
| 13 | 417771-6 | Cover for MT952/3 |
| 14 | 233376-2 | Spring 8 for MT952 |
| 15 | 266050-7 | Screw 4x30 4304 |
| 16 | 213960-9 | O-ring 5 for 9554-58NB |
| 17 | 256546-6 | Pin 4 for 9557-58HNG |
| 18 | 318941-9 | Gear Housing for 9554-58NB |
| 19 | 263002-9 | Rubber Plug SR1800/41KB/JS1650/9901 |
| 20 | 210033-9 | Ball Bearing 696ZZ |
| 21 | 961052-5 | Retaining Ring 12 |
| 22 | 267794-2 | Wave Washer 12 for 9555-58NB |
| 23 | 227542-1 | Gear Wheel 37 for 9554-58NB |
| 24 | 962151-6 | Retaining Ring |
| 25 | 211129-9 | Ball Bearing 6201 |
| 26 | 267238-2 | Washer 12 for MT952/3 |
| 27 | 213622-9 | O-ring 45 for 9554-58NB |
| 28 | 318331-6 | Bearing Case for 9554-58NB |
| 29 | 265099-4 | Screw M4x14 for 9555-58NB |
| 30 | 345464-4 | Gasket for 9555-58NB |
| 31 | 254011-9 | Key HP1300/N800/HP1030 |
| 32 | 324489-1 | Spindle for 9555-58NB |
| 33 | 265180-1 | Screw M5x16 for GA6021 |
| 34 | 122887-1 | Disc Guard 125mm for GA5030 |
| 35 | 224415-9 | Mounting Flange |
| 36 | 224554-5 | Flange Nut |
| 37 | 266623-6 | Tapping Screw 4x80 |
| 38 | 865808-7 | Nameplate for 9558HN |
| 39 | 266007-8 | Screw 3x10 |
| 40 | 643760-7 | Carbon Brush Holder |
| 41 | 194074-2 | Carbon Brushes Set CB-325 for 9555NB, 9558NB |
| 42 | 418729-8 | Spacer for 9557/58NB |
| 43 | 650560-8 | Switch DPX-2110-R for 9554-58NB |
| 44 | 687124-5 | Cable Holder for MT |
| 45 | 265995-6 | Screw 4x18 |
| 46 | 638740-6 | Capacitor |
| 47 | 682559-5 | Cable Cover |
| 48 | 665394-6 | Power Supply Cord H05RN-F |
| 49 | 419566-3 | Switch for 9555-58NB |
| 50 | 451125-7 | Motor Housing for 9557/58NB |
| 51 | 643760-7 | Carbon Brush Holder |
| 52 | 233121-5 | Spring 4 for 9554-58NB |
| 53 | 418728-0 | Switch Lever for 9557/8NB |
| 54 | 418726-4 | Rear Housing for 9555-58NB |
| 55 | 265995-6 | Screw 4x18 |
