User Manual for 5th Wheel Electric Scooter ES09
Model No.: ES09
Original Manual
Version: V1.0
Scan QR Code for Video Tutorial: [QR Code for Video Tutorial]
Contact Email: aftersales@invanti.com
Illustrations and descriptions are for reference only and may vary from the actual product. Network connectivity may be required for full functionality. This product is for safety management and does not replace other safety measures. Do not use for illegal purposes. Invanti is not responsible for third-party services. Please review third-party terms and privacy policies.
© 2024 Invanti (Beijing) Technology Co., Ltd. All rights reserved.
Welcome
Thank you for choosing the 5TH WHEEL Electric Scooter ES09 (hereinafter referred to as ES09). Enjoy the pleasure brought by ES09.
[Image: Illustration of the 5th Wheel ES09 electric scooter]
1. Safety Precautions
Please read the following safety precautions carefully before use.
- The ES09 is intended for adult use only. Do not carry passengers, including children.
- Wear a safety helmet and other protective equipment while riding the ES09. [Image: Person wearing helmet and pads]
- Adhere to local laws and regulations. Do not ride in unsafe or illegal locations.
- Practice riding the ES09 in an open area first, away from heavy traffic. Once familiar with operation, you may use it on roads, respecting local laws.
- Avoid dangerous maneuvers and always ride with both hands on the handlebars. Keep your feet on the scooter.
- Do not ride over uneven surfaces or obstacles higher than 3 cm. This can cause the ES09 to tip over and result in injury or damage. Avoid potholes deeper than 3 cm. [Image: Scooter with 3cm obstacle indicator]
- For safety, do not ride at night if possible. If necessary, turn on the headlight and keep speed below 15 km/h.
- Do not ride at ambient temperatures below -5 °C. [Image: Thermometer showing -5°C]
- On uneven roads or poor road conditions, reduce speed, ride cautiously, or dismount and push the scooter.
- Do not ride on slippery surfaces such as roads with ice or oil. [Image: Scooter on an icy surface with a cross mark]
- Avoid riding through puddles deeper than 4 cm to prevent water from entering electrical components. [Image: Scooter in a puddle with 4cm depth indicator]
- Avoid riding in adverse weather conditions such as rain, snow, and wind to prevent potential damage. [Image: Scooter in rain/snow/wind with a cross mark]
- Follow the important instructions in this manual. Any load placed on the scooter must not exceed its maximum weight capacity. [Image: Scooter with weight limit indicator 265lbs/120kg]
- Avoid using or storing the scooter in extreme temperatures. Keep it away from flammable materials to prevent fires. [Image: Warning sign for fire hazard]
- The ES09 is a specialized vehicle. Ride on flat roads without pits.
- Do not attach any load to the handlebar that could affect the vehicle's stability.
- Engage the kickstand when the vehicle is not in use. Flip up the kickstand before use. Do not park the vehicle on a slope. [Image: Scooter on a slope with a cross mark]
- Minimum user height is 1.4m, maximum is 2.2m. Minimum age is 13 years, maximum age is 70 years. [Image: Height comparison chart]
- Braking performance and tire friction decrease in wet conditions, making control harder. Slow down and brake early when it is raining. [Image: Scooter in rain with warning symbol]
- WARNING: Keep plastic covering away from children to avoid suffocation. [Image: Child with plastic bag symbol]
- Take time to learn the basics of riding to avoid serious accidents, especially in the first month.
- Make yourself known when approaching pedestrians or cyclists, especially if you are not seen or heard. Avoid high-traffic areas or crowded places. [Image: Scooter approaching pedestrian/cyclist]
- Cross protected pedestrian crossings on foot. Always be mindful of yourself and others. [Image: Person walking scooter across a crosswalk]
- Do not perform acrobatic maneuvers with the vehicle. This vehicle is not intended for such use. [Image: Scooter with a cross mark over acrobatic action]
- Caution: The brake may become hot during use. Do not touch it immediately after use.
- Eliminate any sharp edges caused by use. Do not modify or transform the vehicle, including the steering tube, stem, folding mechanism, or rear brake.
- Always wear shoes when riding. [Image: Person wearing shoes]
- Anticipate your trajectory and speed, respecting traffic laws and the most vulnerable road users. Observe any applicable local laws and regulations.
2. About the Scooter
1. Overview
[Diagram: Labeled illustration of the 5th Wheel ES09 electric scooter]
- Turn Signal
- Rear Disc Brake
- LED Headlight
- Folding Buckle
- Scooter Bar
- Folding Switch
- Folding Mechanism
- Front Fender
- Front Fork
- In-wheel Motor
- 10 inches Inner Honeycomb Tyres
- Charging Port
- Built-in Lithium Battery
- Kickstand
- Rear Fender
- Rubber Pedal
- Taillight
- License Plate Frame
- Disc Brake
- LED Display
3. Scooter Appearance
Accessories
[Image: Illustrations of Manual, Screws, Screwdriver, Tool Kit, Power Adapter]
Note: Please check all items in the package carefully. If anything is missing or damaged, please contact: aftersales@invanti.com
| Product Contents | Quantity |
|---|---|
| User Manual | 1 |
| Screws | 4 |
| Screwdriver | 1 |
| Tool Kit | 1 |
| Power Adapter | 1 |
Dimensions
Unfolded Status: 1216mm (Height) x 1154mm (Length) x 505mm (Width)
Folded Status: 460mm (Height) x 1154mm (Length) x 505mm (Width)
4. Scooter Assembly
[QR Code for Video Tutorial]
This QR code is a video tutorial for product use. It is recommended to scan this QR code to learn more about how to use the product.
Important Notes Before Riding:
- Press the power key to turn on the scooter.
- For safety, the ES09 has a non-zero start setting. You need to slide the scooter to 3 km/h for normal operation.
- The scooter can be turned on and pushed, but cannot be ridden in walking mode.
- The scooter cannot be started while charging.
- Do not discard the manual; refer to it for specific operations.
Assembly Steps:
- Unfold the folding mechanism of the ES09 and put down the kickstand. [Diagram: Unfolding the scooter]
- Insert the handlebar into the scooter bar. Connect the line connector in the head and riser. [Diagram: Inserting handlebar and connecting wires]
- Use the tools included in the package to tighten the screws. [Diagram: Tightening screws]
- After assembly, check if the power switch operates normally. [Diagram: Checking power switch]
5. Unfolding/Folding/Carrying
1. Unfolding Operations
- Turn the folding clip clockwise until it is fully open. [Diagram: Step 1 of unfolding]
- Pull up the body lever while opening the folding clip. [Diagram: Step 2 of unfolding]
- Turn the folder clockwise until it is fully snapped. [Diagram: Step 3 of unfolding]
- Check if the folder key is returned to the bottom. [Diagram: Step 4 of unfolding]
2. Folding Operations
Note: For safety, it is recommended to fold the scooter after it is shut down.
- Lift the folder key up. [Diagram: Step 1 of folding]
- Rotate the folder counterclockwise while lifting the folder key. [Diagram: Step 2 of folding]
- Lower the body rod slowly. [Diagram: Step 3 of folding]
- Open the folding clip and hang it on the rear fender buckle. [Diagram: Step 4 of folding]
3. About Carrying
After folding, you can carry the scooter with one or two hands.
4. About Charging
When the indicator light is red, it indicates charging. When fully charged, it turns green. The scooter cannot be opened during charging; unplug the charger to open it. [Image: Charging indicator showing Red (Charging) and Green (Charging completed)]
6. Riding and Parking
Preparation for Riding
- Select an appropriate riding place.
- Unfold the scooter according to the unfolding instructions and wear protective equipment. [Image: Person wearing helmet and pads]
- Ensure the steering system is correctly adjusted, all connection elements (like the folding system) are tightened and not broken, and brakes and wheels are in good condition.
Riding
- Press the power button to turn on the scooter.
- Place one foot on the footboard and the other on the ground.
- Slide the scooter forward to 3 km/h and gently press the right thumb accelerator. The scooter will move forward slowly. Once steady, place your other foot on the footboard. The more you press the accelerator, the higher the speed.
Note: For riding safety, the ES09 has a non-zero start mode. The accelerator only engages after the scooter has moved a short distance.
[Image: Scooter moving at 3km/h with accelerator pressed]
Parking
Normally, the scooter stops immediately when you press the left brake lever. The harder you press, the greater the braking force. [Image: Hand pressing brake lever]
7. Control System
[Diagram: Close-up of handlebars showing controls]
- Disc brake: Hold the left brake handle. Greater pressure equals greater braking force.
- Bell: [Bell Symbol]
- Turn Signal: Controls for left and right turn signals.
- Thumb throttle: Controls acceleration.
- Power Button: Short press to turn on, long press for 2s to turn off. Press once for headlight. Double press to switch gear mode. Press five times continuously to switch speed unit.
Turn Signal Control
Short press the left/right button to turn the respective turn signal on/off. Press and hold the left or right button for 3 seconds to activate the flash function. Press the left or right button again to deactivate the flash function.
8. Indication Description
LED Headlight Status Indication
| Switch On | Switch Off |
|---|---|
| If the LED headlight is switched on, the indicator remains on. | If the LED headlight is switched off, the indicator is off. |
4 Gears Indication
| Work Mode | ECO Mode | D Mode | S Mode |
|---|---|---|---|
| The Work mode is enabled. | The ECO mode is enabled. | The D mode is enabled. | The S mode is enabled. |
Brief Use Instructions
When the scooter is powered off, briefly press the Power switch to turn it on. When operating, long press the Power switch to turn it off. Click the switch key to turn the front lights on/off. Double press the Power switch to switch gears (Work, ECO, D, S modes). The scooter saves the last selected gear.
9. Troubleshooting
If there is any abnormal issue with the scooter, the warning indicator will flash, displaying error codes 4-55.
| Error Code | Description | Inspection and Handling |
|---|---|---|
| 4 | Short circuit | Check for wired or installed short circuits, or replace the controller. |
| 10 | Instrument panel communication failed | Check the connection between the instrument panel and the controller assembly line. Shut down and restart the vehicle after re-plugging the connection. |
| 11 | Motor current sensor is abnormal | Check the phase line of the controller or motor. |
| 14 | Throttle Hall anomaly | Check if the throttle is zero, and if the throttle line and throttle are normal. Unplug the throttle cord and restart the vehicle. |
| 15 | Brake Hall anomaly | Check if the brake lever resets to zero position, and if the brake line and brake are normal. Unplug the electronic brake wiring and restart the vehicle. |
| 16 | Motor Hall anomaly | BOOT failure. Check if the motor Hall wiring is normal. If braking issues occur, check or replace the motor or controller. |
| 28 | Upper bridge MOS tube fault | MOS tube failure reported. Controller may need replacement after restart. |
| 29 | Lower bridge MOS pipe failure | MOS tube failure reported. Controller may need replacement after restart. |
| 50 | Bus high voltage | Main line voltage too high. BOOT failure. Check battery voltage. If issues persist during riding, replace battery or controller. |
| 53 | System overload | System load exceeded. BOOT failure. Replace controller. |
| 54 | MOS phase line short circuit | Check phase line wiring for short circuits. |
| 55 | Controller high temperature alarm | Controller temperature too high. Let the vehicle cool down before restarting. If BOOT failure occurs, replace controller. |
10. About Charging
To charge:
- Remove the rubber protective cover of the charging port. [Image: Hand removing charging port cover]
- Connect the charger. [Image: Charger connected to port]
- After charging, push the rubber protective cover back in. [Image: Cover replaced]
1. Remove the rubber protective cover and insert the charger connector into the charging port.
2. Insert the charger's power plug into a power socket.
3. The charger indicator is red while charging and turns green when fully charged.
4. The vehicle must be powered off or in a non-operational mode during charging.
11. About the Battery and Charger
Each ES09 electric scooter comes with a dedicated lithium battery and smart charger. Do not use chargers from other brands. The company is not liable for damage caused by improper use.
Battery
The lithium battery supports at least 800 recharge cycles, and over 1,000 times under normal conditions. Fully charge the battery before first use. It can be charged anytime without damage. If not in use for extended periods, charge it every 3 months.
12. Operating Temperature
Charging: 0 °C to 45 °C
Discharging: -10 °C to 60 °C
Charger
The provided charger has protection and automatically shuts off at 100% charge. Charging time is approximately 4-5 hours. Damage from water, collision, or other factors is not covered by warranty.
Production Factory: Shenzhen HaiLongTong Technology Co., Ltd.
Model: HLT-180-4201500
Input: AC100-240V 50/60Hz 2.0A MAX
Output: DC42V ⎓ 1.5A
Charging Instructions
- Open the rubber cover and insert the plug into the port.
- Insert the charger plug into the electrical outlet.
- The indicator lamp is red when charging and green when fully charged.
- Shut down the scooter and keep it away from water before charging.
- Use only the specified charger.
- Warning: Be careful to avoid electric shock.
Kinetic Energy Recovery
Pressing the brake activates the kinetic energy recovery system, converting kinetic energy into electrical energy for storage. This enhances emergency braking and increases range. Power changes are displayed simultaneously.
13. App Descriptions
App Manual Operation
The App UI may change with updates. Follow instructions based on the current version.
- Scan the QR code or search "5thWheel" in your mobile app store to download and install the App. [QR Code for App Download]
- Open the App, complete registration, log in, and tap "+" or "Search Devices" to add your scooter. Follow the prompts. [Image: Android/iOS app interface with '+' and 'Add Device' icons]
If you have installed our App, please ensure it is the latest version.
If scanning fails, ensure Bluetooth and the scooter are on, then try again.
14. Maintenance
Lubrication
Apply a small amount of white grease or lubricant to the folded part every six months. Check screws for looseness every three months and tighten as needed.
Battery
Fully charge the battery before first use. It can be charged anytime. If not in use, charge every three months.
*Laboratory data
Storage and Daily Maintenance
Avoid direct sunlight and humid conditions for extended periods. Keep the scooter clean. Regularly check and tighten bolted elements, especially wheel axles, folding mechanism, steering system, and brake shaft.
Cleaning Recommendations
Wipe stains with a damp cloth. For stubborn stains, use toothpaste and a toothbrush, then wipe clean. Do not use solvents like alcohol or gasoline. Do not use a high-pressure washer. Ensure the scooter is off, unplugged, and the charging port flap is closed during cleaning to prevent electric shock or other issues.
Routine Inspection
- Before riding, confirm the folding mechanism is locked.
- Check tires for excessive wear. Contact an authorized dealer for replacement if needed.
- Verify tire pressure is at the standard value. Inflate if too low.
- Inspect brake pads for wear that affects braking performance. Contact an authorized dealer if issues arise.
- Screws are self-tightening; their effectiveness may decrease after multiple tightenings.
15. Common Problems and Solutions
If you encounter any problems, try the following solutions:
1. Display Screen is Black
Possible Cause: Prolonged sun exposure.
Solution: Place the scooter in a dark environment for a period; the display should return to normal.
2. Displayed Value is Inconsistent
Possible Cause: Parameter setting is incorrect or missing.
Solution: Long press the Power switch to shut down, then short press to restart.
3. Digital Display is Dim
Possible Cause: Loose battery connection or low battery.
Solution: Turn off and restart the scooter. If the problem persists, contact customer service at aftersales@invanti.com.
4. Product Does Not Work Normally
- Ensure the scooter is powered on.
- Check battery level on the display.
- Verify the left brake and rear brake are engaged.
- Confirm all ports and power cables are connected correctly.
- If all steps are checked and the product still malfunctions, contact customer service at aftersales@invanti.com.
16. Parameter Configuration
| Parameter | Value |
|---|---|
| Product name | Electric Scooter |
| Model | ES09 |
| Size (Unfolded L×W×H) | 1154mm×505mm×1216mm |
| Size (Folded L×W×H) | 1154mm×505mm×460mm |
| Weight (Net) | Approx. 14.6 kg |
| Status (Max. Load Capacity) | 120kg |
| Status (Max. Hourly Speed) | Approx. 20 km/h |
| Main parameters (Full-battery endurance) | 32 km (depending on environment, angle, speed, driving habits, etc.)* |
| Main parameters (Max. Slope) | 15% |
| Main parameters (Scope of application) | Smooth road surface, with protrusions < 2 cm and depressions < 3 cm |
| Main parameters (Tyre) | 10 inches Inner Honeycomb Tyres |
| Main parameters (Shock-absorbing System) | Concealed Damping |
| Main parameters (Waterproof Level) | IP54 |
| Main parameters (Brake system) | Disc brake, Electronic brake |
| LED display | Speed, gear, headlight, speed unit, battery |
| Lighting system | LED high-brightness headlight |
| Motor power | 350W |
| Charging parameters (Adapter Rated input voltage) | 100V-240VAC 50/60Hz |
| Charging parameters (Lithium battery) | 37V/7.5Ah |
| Charging parameters (Charging time) | 5-6h |
*Maximum endurance: Measured at full power, 75kg load, ambient temperature 25°C, constant speed on a flat, hardened road at 60% of maximum speed. Actual endurance varies by weight, temperature, and road conditions.
17. Authentication
EU Compliance Statement
WEEE requires proper disposal and recycling. This symbol indicates the product should not be disposed of with domestic waste in the EU. Recycle to prevent environmental harm and promote sustainable resource reuse. Use return/collection systems or contact retailers for environmentally safe recycling.
EU Battery Recycling Information
Batteries are marked per European Directive 2006/66/EC and amendment 2013/56/EU. This directive covers the recycling framework for waste batteries and accumulators across the EU. The label indicates batteries should not be discarded but recycled at end-of-life. Battery labels may include chemical symbols for relevant metals (Pb, Hg, Cd). Users must use available collection frameworks for recycling and disposal, minimizing environmental and health impacts. Batteries and accumulator cells must be removed for separate collection before disposing of electrical and electronic equipment (EEE).
[CE Mark]
Restriction of Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
Products and parts (cables, wires, etc.) comply with Directive 2011/65/EU regarding the restriction of hazardous substances in electrical and electronic equipment.
Trademark and Legal Statements
5TH WHEEL and its logo are trademarks of Invanti (Beijing) Technology Co., Ltd., used under license. Android and Google Play are trademarks of Google Inc. App Store is a service mark of Apple Inc. Their respective owners reserve trademark rights. Products under the 5TH WHEEL trademark are protected by patent laws. This manual aims to describe all instructions and functions of the ES09 electric scooter. Due to constant updates, the actual product may differ slightly from the manual. Visit the Apple App Store (iOS) for more information. Invanti develops products with multiple functions and models; some features mentioned may not apply to your specific product. The manufacturer reserves the right to change the design and function of the ES09 and its documentation without prior notice.
© 2024 Invanti (Beijing) Technology Co., Ltd. All rights reserved.
Contact Us
If you encounter any problems during use, please contact us via the following methods or scan the QR code for a quick response and satisfactory solution.
Amazon Platform: "Contact Seller"
Email Address: aftersales@invanti.com
Get 24/7 Customer Service
[QR Code for Contact]
