Manuals+

Ecler VIVO-X8D8 / BIO-X8G User Manual

Digital Processors & Matrixes

EclerPLEX Matrix 8x8 Analogue 8x8 Dante/AES67

EclerPLEX Expansion Interface 8x8 Analogue Audio 8x8 GPIO

1. Precautions

1.1 Important Notice

CAUTION RISK OF ELECTRIC SHOCK - DO NOT OPEN

WARNING: SHOCK HAZARD - DO NOT OPEN

AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR

⚠️ The flashing light with an arrowhead symbol inside an equilateral triangle is intended to alert the user of the presence of non-insulated “dangerous voltage” within the enclosure, which might be of sufficient magnitude to pose a risk of electric shock to users.

⚠️ The exclamation mark within an equilateral triangle is intended to alert the user of the requirement for important operating and maintenance (servicing) instructions, for which instructions may be found in the literature accompanying the appliance.

WARNING (If applicable): Terminals marked with symbol "⚡" may be of sufficient magnitude to pose a risk of electric shock. The external wiring connected to terminals requires installation by a technician, or the use of ready-made leads or cords.

WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or humidity.

WARNING: A device with Class I manufacturing ought to be connected to a mains socket outlet with a protective earthing connection.

WARNING: Ecler products have a long lifetime of more than 10 years. This product must never be discarded as unsorted urban waste, but must be taken to the nearest electrical and electronic waste treatment centre.

1.2 Key Safety Directions

  1. Read the following directions.
  2. Keep the following directions.
  3. Observe all warnings.
  4. Follow all instructions.
  5. Do not use this device in proximity to water.
  6. Clean only with a dry cloth.
  7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that may release heat.
  9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades, with one being wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, contact a qualified electrician for a replacement of the obsolete outlet.
  10. Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles, and at the point of exit from the device.
  11. Only use attachments/accessories specified by the manufacturer.
  12. Unplug the device during lightning storms or when unused for long periods.
  13. Refer all servicing to qualified personnel. Servicing is required when the device has been damaged in any way, such as power supply cord or plug damage, liquid spillage or objects onto the device, the device has been exposed to rain or humidity, does not operate normally, or has been dropped.
  14. Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket, therefore, it should always remain easily accessible.
  15. Equipment is connected to a socket-outlet with an earthing connection by means of a power cord.
  16. The marking information is located at the top/rear of the unit.
  17. The device shall not be exposed to dripping or splashing liquids, and no liquid-filled objects, such as a filled up glass, shall be placed on top of the device.

1.3 Cleaning Directions

Clean the unit with a soft, dry clean cloth or slightly wet with water and neutral liquid soap only, then dry it with a clean cloth. Be careful that water never gets into the unit through any hole. Never use alcohol, benzine, solvents or abrasive substances to clean this unit.

NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be caused to people, animal, or objects due to failure to comply with the warnings above.

2. Warranty & Environment

Thank you for choosing the Ecler VIVO-X8D8 / BIO-X8G!

We greatly value your trust.

It is VERY IMPORTANT to carefully read this manual and to fully understand its contents before any connecting takes place in order to make the best use of this equipment, as well as to get the best performance from it.

To ensure optimal operation of this device, we strongly recommend that its maintenance be carried out by authorised Technical Services.

All ECLER products are covered by warranty; please refer to www.ecler.com or the warranty card included with this product for the period of validity and conditions.

Ecler is truly committed to the environment and planet sustainability, energy saving and CO2 emission reduction. Recycling materials and using non-contaminant components are also top priorities in our green crusade.

Ecler has deeply evaluated and analyzed the environmental impacts of all the processes involved in the production of this product, including packaging, and has alleviated, reduced and/or compensated for them.

3. Package Contents

4. Description & Features

4.1 VIVO-X8D8

VIVO-X8D8 is an EclerPLEX Host matrix with 8 analogue and 8 Dante/AES67 audio input ports, 8 analogue and 8 Dante/AES67 audio output ports, scalable thanks to two X-link ports. A BIO-X8 (or BIO-X8G) expansion unit can be connected to each X-link port. VIVO-X8D8, performing as a Host unit in an EclerPLEX deployment, can contain multiple projects running simultaneously and serve user control panels to end users.

4.1.1 Main Features

4.2 BIO-X8G

BIO-X8G is an affordable expansion interface that can easily scale up an EclerPLEX digital host matrix, adding to its default size 8 input and 8 output analogue audio ports, 8 GPI ports and 8 GPO ports. A maximum of 2 BIO-X8G units can be linked to the same EclerPLEX host matrix, reaching a maximum total matrix size of 24 analogue audio input ports, 24 analogue audio output ports and 24x24 GPIO control ports.

4.2.1 Main Features

5. Install & Connect

5.1 Location, Assembly and Ventilation

VIVO-X8D8 and BIO-X8G have been specially designed to be placed in 19" rack structure, occupying one unit.

⚠️ It is very important to ensure that the device is neither enclosed nor exposed to extreme temperatures, as it generates heat. Adequate airflow must be maintained through the ventilation holes in the chassis, with the ventilation system directing the airflow from front to back through the unit.

⚠️ If multiple devices are installed in the same rack or in a cabinet with closed doors, it is highly recommended to install fans at both the upper and lower ends to create a forced airflow from the bottom up. This upward air flow will help to dissipate the heat generated inside.

⚠️ Regular maintenance of dust removal is highly recommended to ensure optimal performance as dust can impede airflow and hinder heat dissipation.

5.2 Mains Connection

VIVO-X8D8 and BIO-X8G operate on alternating voltages ranging from 90 to 264V and 47 to 63hz. These devices feature an oversized power supply that can adapt to the mains voltage of any country in the world without requiring any adjustments.

Connect each device to the mains and press the ON/OFF button of the rear panel.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit with various ports labeled, including power switch, mains socket, RS-232, µSD, NET1/NET2, X-LINK, GPO, GPI, OUT, IN.]

[Diagram: Shows the rear panel of the BIO-X8G unit with various ports labeled, including power switch, mains socket, X-LINK, GPO, GPI, OUT, IN.]

? Each device is equipped with a front panel LED indicator that illuminates green when the unit is operational.

[Diagram: Shows the front panel of the VIVO-X8D8 unit with a display and several buttons/LEDs.]

[Diagram: Shows the front panel of the BIO-X8G unit with a single LED indicator.]

5.3 VIVO-X8D8 and BIO-X8G interconnection

⚠️ The BIO-X8G device cannot work without a VIVO-X8D8 device as the VIVO-X8D8 is a primary/controller device and the BIO-X8G works as an expansion.

To connect a BIO-X8G to a VIVO-X8D8 device, use an Ecler certified USB-C to USB-C cable (supplied with each BIO unit) and connect it to the X-LINK connector located on the rear panel of both devices.

[Diagram: Illustrates the interconnection between a VIVO-X8D8 unit and two BIO-X8G units using X-LINK cables.]

? Each VIVO-X8D8 unit can support up to two BIO-X8G devices.

? When the VIVO and BIO devices are interconnected, the X-LINK LED indicator on the front panel of the BIO-X8G will illuminate white. It will blink during the synchronization process and stay continuously lit once the sync is complete and stable.

5.4 Analogue Input Connections

VIVO-X8D8 and BIO-X8G feature 8 balanced analogue signal inputs (IN 1 to 8) on their rear panels, supporting both line and microphone levels. Signal management is handled through the EclerPLEX web interface.

Signal input connectors are Euroblock, type 3 position screw terminal block. The wiring is:

[Diagram: Shows wiring for BALANCED and UNBALANCED analogue audio connections using Euroblock terminals, illustrating pin assignments for signal, non-phase, and ground.]

⚠️ For unbalanced connection, short-circuit pin to pin as reported on the picture.

5.5 Analogue Output Connections

VIVO-X8D8 and BIO-X8G feature 8 balanced analogue signal outputs (OUT 1 to 8) with line level.

Signal input connectors are Euroblock, type 3 position screw terminal block. The wiring is:

[Diagram: Shows wiring for BALANCED and UNBALANCED analogue audio output connections using Euroblock terminals, illustrating pin assignments for signal, non-phase, and ground.]

⚠️ For unbalanced connection, short-circuit pin to pin as reported on the picture.

5.6 Digital Audio Inputs and Outputs

VIVO-X8D8 supports the reception and transmission of 8 channels of digital audio via Dante/AES67 over an Ethernet network, which is compatible with the Dante/AES67 protocol for digital audio over IP.

The routing of digital audio signals via Dante/AES67 through the Ethernet network, along with the configuration of Dante/AES67 network ports (IP addresses, mask, etc.) for the VIVO-X8D8, is managed by the Dante Controller software application.

For further details, please refer to the developer's documentation: www.audinate.com/products/software/dante-controller.

5.7 Ethernet Ports

VIVO-X8D8 features two RJ-45-type ETHERNET connectors on the rear panel, named NET1 and NET2, which allow the equipment to be connected to an Ethernet network, or directly to a computer or other devices with an Ethernet interface, point-to-point.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit highlighting the NET1 and NET2 Ethernet ports.]

1. NET1 (Control): WebGUI, user control panels, third party control and other control packages are sent/received over NET1.

2. NET2 (Control + Dante/AES67): control and Dante/AES67 Audio perform over the same network.

This connection enables the following within a local network:

5.8 Player and microSD card

VIVO-X8D8 integrates a set of stereo audio players (SW embedded) capable of playing audio files from a local storage device (microSD card), suitable for background music or voice messages. It includes playlist management and integration with the device's calendar events for automation. Customizable user control panels are also available, and the system is fully configurable through the EclerPLEX web application.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit highlighting the microSD card slot.]

? To insert the microSD card, push it into the slot until a click sound is heard. To extract it, push the microSD card inside the slot until a click sound is heard, and it will be released.

5.9 GPI Ports

VIVO-X8D8 and BIO-X8G rear panels feature eight 0-12VDC remote control ports, labelled "GPI 1-8”, to connect analogue devices such as the WPa / TOCA series wall panels. Using the EclerPLEX web application, functions can be assigned to each of these ports, allowing remote control of the volume of sources, outputs, and local and network groups, including general volume. Additionally, presets or playlists can be loaded.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit highlighting the GPI ports.]

[Diagram: Shows the rear panel of the BIO-X8G unit highlighting the GPI ports.]

The GPI connectors are Euroblock type. The assignment of the connection is as follows:

5.10 GPO Ports

VIVO-X8D8 and BIO-X8G rear panel feature 8 relay outputs NO / NC (normally open / normally closed). Each output's status can be associated with user presets or events through the EclerPLEX web application, enabling functions such as calendar events or the touch of a key on a user panel. This allows interaction with external equipment, including motors for projection screens, movable partition walls, lights, sirens, and GPI inputs from other devices.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit highlighting the GPO ports.]

[Diagram: Shows the rear panel of the BIO-X8G unit highlighting the GPO ports.]

5.11 RS-232 Remote Control Port

The RS-232 port, with an Euroblock connector on the rear panel of the VIVO-X8D8, allows an external device to communicate with the unit via serial communication. This connection uses the syntax of the TP-NET protocol so that the external device can obtain the value of some of the parameters of the VIVO-X8D8 unit (by means of “GET” commands) and/or modify these values (“SET” commands).

[Diagram: Shows the rear panel of the VIVO-X8D8 unit highlighting the RS-232 port.]

The serial connection must comply with the following characteristics:

6. Start-Up & Operation

6.1 Start Up

Connect each device to the AC mains and press the ON/OFF button of the rear panel.

[Diagram: Shows the rear panel of the VIVO-X8D8 unit with the power switch highlighted.]

[Diagram: Shows the rear panel of the BIO-X8G unit with the power switch highlighted.]

? Each device features a front panel LED indicator that lights up when the unit is operational.

[Diagram: Shows the front panel of the VIVO-X8D8 unit with its operational LED.]

[Diagram: Shows the front panel of the BIO-X8G unit with its operational LED.]

6.2 First Steps and Operation

To access the EclerPLEX web application from an external device (computer, tablet, etc.) using a browser, first make sure both devices are physically connected to the same local network (LAN) and configured within the same network range.

? DHCP is the default network configuration mode. If you have a router/switch with a DHCP server (see the specifications for your device), network configuration is automatic so there is no need to do any re-configuration.

There are two ways to connect to the embedded VIVO host unit web application.

6.2.1 Automatic Connection Using a Computer

  1. Connect the VIVO-X8D8 device to the router/switch using a CAT5 or higher cable (NET1 or NET2 Ethernet port on the VIVO-X8D8 device).
  2. Connect your browser equipped device (computer, tablet, etc.) to the same local network (router/switch). You can do this over a wired or WiFi connection, depending on your network device and computer/tablet.
  3. Enter into your browser the web address shown on the top panel of the device or on the packaging (http://vivo-x8-xxxx.local). The last four digits of the web address correspond to the MAC address of the device.

[Diagram: Shows a VIVO-X8D8 unit connected to a network, with an arrow indicating the web address on the top panel.]

6.2.2 Manual Connection

If you do not have a DHCP server, are unsure whether you have one, or just want to establish a point-to-point connection with a computer:

  1. Connect the VIVO-X8D8 device to the computer using a CAT5 cable or higher (NET1 or NET2 Ethernet port on the VIVO-X8D8 device).
  2. If the VIVO-X8D8 device cannot find a DHCP server, it will be able to an automatic private IP addressing (APIPA) and subnet mask from NET1; the device will select its own IP address in the address range 169.254.1.0 to 169.254.254.255 and will also be reachable via the mDNS service.
  3. Otherwise, the device will also remain accessible via the auxiliary IP. Enter NET1 or NET2 IP address in the browser and configure:

6.2.3 Login

There are two profiles that can access the app:

  1. Administrator: An administrator has access to all functions of the VIVO-X8D8 device and can configure any matrix parameter, event, peripherals, etc. An administrator creates users and control panels for the EclerPLEX user app.
  2. User: Users (non-administrator users or end-users of the system) have limited access. The only functions available to normal users are controls (e.g. controlling the volume of an output) but no configuration functions.

[Diagram: Illustrates user access roles, showing a central 'ADMIN' figure connected to 'USER1', 'USER2', and 'USERN' figures, representing different access levels.]

Administrator and user access are password-protected. The default administrator access credentials are:

7. Panel Functions

7.1 VIVO-X8D8

7.1.1 Front Panel

[Diagram: Shows the front panel of the VIVO-X8D8 unit with numbered controls: 1 (<: button), 2 (Enter button), 3 (>: button), 4 (Func LED), 5 (Dante LED), 6 (On LED).]

  1. <: This button allows moving through the display different screens.
  2. Enter: Enter button.
  3. >: This button allows moving around the display different screens.
  4. Func LED: Programmable LED. Can be programmed by the user via EclerPLEX.
  5. Dante LED: Lights up when there is a connection with Dante, according to the following status:
    • LED colour | Status
    • Red | PTP error / no PTP sync / PTP synchronization disabled
    • Orange | PTP synchronization in progress.
    • Green (solid) | PTP follower, with PTP sync
    • Green (flashing) | PTP leader
  6. On LED: Lights up in green if the unit is on.

7.1.2 Rear Panel

[Diagram: Shows the rear panel of the VIVO-X8D8 unit with numbered ports: 1. Power Switch, 2. Mains socket, 3. RS-232, 4. µSD, 5. NET1 / NET2, 6. X-LINK ports, 7. GPO (8), 8. GPI (8), 9. OUT (8), 10. IN (8).]

  1. Power Switch: Unit Power ON switch.
  2. Mains socket base.
  3. RS-232: Euroblock connector for remote control via TP-NET protocol, RS-232.
  4. µSD: microSD card slot.
  5. NET1 / NET2: RJ-45 ethernet network ports, NET1-2.
  6. X-LINK ports: USB-C to USB-C connection to one BIO-X8G to each port.
  7. GPO (8): GPO ports 1-8.
  8. GPI (8): GPI ports 1-8.
  9. OUT (8): Analogue outputs 1-8, 3-pin Euroblock. Pitch: 3,5 mm.
  10. IN (8): Analogue inputs 1-8, 3-pin Euroblock. Pitch: 3,5 mm.

7.2 BIO-X8G

7.2.1 Front Panel

[Diagram: Shows the front panel of the BIO-X8G unit with numbered controls: 1 (X-LINK LED), 2 (On LED).]

  1. X-LINK: When this LED lights white, it indicates active connection with the VIVO-X8D8. It will blink during the synchronization process and stay continuously lit once the sync is complete and stable.
  2. On LED: This LED lights up in green colour if the unit is on.

7.2.2 Rear Panel

[Diagram: Shows the rear panel of the BIO-X8G unit with numbered ports: 1. Power Switch, 2. Mains socket, 3. X-LINK, 4. GPO (8), 5. GPI (8), 6. OUT (8), 7. IN (8).]

  1. Power Switch: Unit Power ON switch.
  2. Mains socket base.
  3. X-LINK: USB-C to USB-C connection to the VIVO-X8D8.
  4. GPO (8): GPO ports 1-8.
  5. GPI (8): GPI ports 1-8.
  6. OUT (8): Analogue outputs 1-8, 3-pin Euroblock. Pitch: 3,5 mm.
  7. IN (8): Analogue inputs 1-8, 3-pin Euroblock. Pitch: 3,5 mm.

8. Technical Data

8.1 Technical Specifications

8.1.1 VIVO-X8D8

CategoryParameterProcessorQuad core 64bits 1,5GHz
Digital EngineSampling rate48 kHz
Resolution32 bit
Latency<4ms
Frequency response10Hz to 20kHz (-0,5 dB)
Dynamic rangeADC:115dB, DAC: 115dB
Analogue Audio Input PortsNumber of input ports8, MIC/LINE level
Connection typeEuroblock, 3-pin, balanced
Input sensitivity-32,5 dBV to +18,5 dBV
-30,3 dBu to +20,7 dBu
Input impedance7k6Ω (balanced), 3k8Ω (unbalanced)
Max input level18,5 dBV/ 20,7dBu
Mic preamp EIN<-129,5 dBV
<-127,3 dBu
Dynamic rangeGain 0 dB:>110,2 dB
Gain 21 dB:>109,5 dB
Gain 42 dB:>105,5 dB
Gain 51 dB:>99,5 dB
THD + NoiseGain 0 dB & Vin 0 dBV:0,0025%
Gain 21 dB & Vin -21 dBV:0,0026%
Gain 42 dB & Vin -42 dBV:0,0044%
Gain 51 dB & Vin -51 dBV:0,0085%
Gain 0 dB & Vin +17 dBV:0,0010%
Gain 21 dB & Vin -4 dBV:0,0015%
Gain 42 dB & Vin -25 dBV:0,0010%
Gain 51 dB & Vin -34 dBV:0,0015%
CMRR>70dB typ (1kHz)
>60 dB typ (20 Hz - 20kHz)
Phantom power+48VDC, 10mA per input max
Analogue Audio Output PortsNumber of output ports8, LINE level
Connection typeEuroblock, 3-pin, balanced
Max output level18,5dBV/ 20,7dBu
Output impedance300Ω (balanced), 150Ω (unbalanced)
Dynamic range> 112,5 dB
Crosstalk> 95dB
Audio Over IPProtocolsDante® / AES67
Number of digital input ports8
Number of digital output ports8
Interfaces1 x RJ-45 - NET2

8.1.2 BIO-X8G

CategoryParameterValue
Audio ConvertersSampling rate48 kHz
Resolution32 bit
Latency<4ms
Frequency response10Hz to 20kHz (-0,5 dB)
Dynamic rangeADC:115dB, DAC: 115dB
Analogue Audio Input PortsNumber of input ports8, MIC/LINE level
Connection typeEuroblock, 3-pin, balanced
Input sensitivity-32,5 dBV to +18,5 dBV
-30,3 dBu to +20,7 dBu
Input impedance7k6Ω (balanced), 3k8Ω (unbalanced)
Max input level18,5 dBV/ 20,7dBu
Mic preamp EIN<-129,5 dBV
<-127,3 dBu
Dynamic rangeGain 0 dB:>110,2 dB
Gain 21 dB:>109,5 dB
Gain 42 dB:>105,5 dB
Gain 51 dB:>99,5 dB
THD + NoiseGain 0 dB & Vin 0 dBV:0,0025%
Gain 21 dB & Vin -21 dBV:0,0026%
Gain 42 dB & Vin -42 dBV:0,0044%
Gain 51 dB & Vin -51 dBV:0,0085%
Gain 0 dB & Vin +17 dBV:0,0010%
Gain 21 dB & Vin -4 dBV:0,0015%
Gain 42 dB & Vin -25 dBV:0,0010%
Gain 51 dB & Vin -34 dBV:0,0015%
CMRR>70dB typ (1kHz)
>60 dB typ (20 Hz - 20kHz)
Phantom power+48VDC, 10mA per input max
Analogue Audio Output PortsNumber of output ports8, LINE level
Connection typeEuroblock, 3-pin, balanced
Max output level18,5dBV / 20,7dBu
Output impedance300Ω (balanced), 150Ω (unbalanced)
Dynamic range> 112,5 dB
Crosstalk> 95dB
ConnectivityX-LINK1, X-LINK port. USB-C connector
Remote Control ConnectionsGPIs8, 0 to 12VDC
GPOs8, 3 poles isolated relay; Contact rating: 2A, 30VDC; 0,5A, 125 VAC
ElectricalPower supplyInternal. Universal, regulated switching mode supply
AC mains requirement90-264 VAC @ 47-63Hz
AC mains connectorIEC C14 inlet
Power consumption16 W / 32 VA
PhysicalOperating temperatureMin: 0°C; 32°F, Max: 50°C; 122°F
Operating humidity5-85% RH, non-condensing
Storage temperatureMin: 0°C; 32°F, Max: 50°C; 122°F
Storage humidity5-85% RH, non-condensing
Installation optionsDesktop, 19" racks (1RU)
Included accessories1x EU Mains cord, 1x Multiplug Mains cord, 4x Washers, 4x Rubber feet, 2x USB holders, 2x Screws.
Dimensions (WxHxD)482.4 x 44 x 214 mm / 18.99 x 1.73 x 8.43 in.
Weight3.2 kg / 7.05 lb
Shipping dimensions (WxHxD)585 x 385 x 75 mm / 23.03 x 15.15 x 2.95 in.
Shipping weight4.65 kg/10.25 lb

8.2 Mechanical Diagram

8.2.1 VIVO-X8D8

All measurements are in mm.

[Diagram: Shows front, top, and side views of the VIVO-X8D8 unit with dimensions in mm. Key dimensions include overall width 482.4mm, front panel width 432mm, height 44mm (1RU), and depth 214mm.]

8.2.2 BIO-X8G

All measurements are in mm.

[Diagram: Shows front, top, and side views of the BIO-X8G unit with dimensions in mm. Key dimensions include overall width 482.4mm, front panel width 432mm, height 44mm (1RU), and depth 214mm.]

Contact Information

All product characteristics are subject to variation due to production tolerances.

NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications.

For technical queries contact your supplier, distributor or complete the contact form on our website, in Support / Technical requests.

Motors, 166-168 | 08038 Barcelona, Spain | Tel. (+34) 932238403 | information@ecler.com | www.ecler.com

Models: VIVO-X8D8 BIO-X8G Digital Processors and Matrixes, VIVO-X8D8 BIO-X8G, Digital Processors and Matrixes, Processors and Matrixes, Processors, Matrixes

File Info : application/pdf, 28 Pages, 1.77MB

PDF preview unavailable. Download the PDF instead.

1752507981-ecler-bio-x8g-user-manual-en

References

Enriqueta Arboli Adobe PDF Library 25.1.51

Related Documents

Preview Ecler VIVO-X8D8 Digital Processor & Matrix Technical Data Sheet
Technical specifications and overview of the Ecler VIVO-X8D8, an EclerPLEX Host matrix with 8 analogue and 8 Dante/AES67 audio input/output ports, expandable for digital audio processing and matrix applications.
Preview Ecler VIVO-X8D8 / BIO-X8G User Manual: Digital Processors & Matrixes
Comprehensive user manual for the Ecler VIVO-X8D8 and BIO-X8G digital processors and matrixes, covering installation, connection, features, operation, and technical specifications.
Preview Ecler VIVO-X8D8 / BIO-X8G Bedienungsanleitung
Bedienungsanleitung für die Ecler VIVO-X8D8 und BIO-X8G digitalen Matrizen und Prozessoren. Enthält Informationen zu Installation, Anschluss, Bedienung und technischen Spezifikationen.
Preview Ecler VIVO-X8D8 / BIO-X8G Manual de Usuario
Manual de usuario para los procesadores digitales y matrices Ecler VIVO-X8D8 y BIO-X8G. Cubre instalación, funcionamiento, características, conexiones y especificaciones técnicas.
Preview Ecler MIMO7272DN Digital Audio Matrix User Manual
Comprehensive user manual for the Ecler MIMO7272DN, a 72x72 digital audio matrix with DANTE™/AES67 interface, covering installation, features, technical specifications, and TP-NET protocol.
Preview Ecler MIMO4040CDN: Manual de Usuario - Matriz Digital de Audio con Cancelación de Eco y DANTE/AES67
Manual de usuario completo para la matriz digital de audio Ecler MIMO4040CDN. Cubre instalación, características, especificaciones técnicas, protocolo TP-NET, gestión AEC y códigos de error.
Preview Ecler MIMO7272DN Digital Matrix User Manual
Comprehensive user manual for the Ecler MIMO7272DN digital audio matrix with DANTE™/AES67 interface. Covers installation, features, technical specifications, and TP-NET protocol.
Preview Ecler BIO-X8G Digital Processors & Matrixes Technical Data Sheet
Technical data sheet for the Ecler BIO-X8G, an affordable EclerPLEX expansion interface for digital host matrices, offering 8 analogue audio I/O and 8 GPIO ports.