ASUS TUF-AX4200 Dual Band WiFi Router

Hardware Explanations

I/O Ports Overview:

• USB 3.2 Gen 1x1 port
• 2.5G/1G WAN (Internet) port
• Power button
• WPS button
• Power (DCIN) port
• Reset button
• LAN 1~4 ports

LED Lights Overview:

• Power LED
• 5GHz LED
• 2.5G WAN (Internet) LED
• 2.4GHz LED
• LAN 1~4 LEDs

Specifications:

Router Setup Steps

1. 01 Prepare your Modem

   • Unplug the power cable of your modem.
   • Connect your modem to the WAN port at the back of the router using the provided network cable.
   • Power on the modem. Plug the modem into the power outlet and power it on.
   • Check the modem LED lights to ensure the connection is active.
   • Note: If you are using DSL for internet, you will need your username/password from your Internet Service Provider (ISP) to properly configure your router.

2. 02 Install your Router

   • Plug the adapter into the DCIN port and press the Power button.
   • The power LED will light up when the hardware is ready.

   Setup via App:

   • On your iOS or Android mobile device, go to the app store, search for ASUS Router, and download the app.
   • On your mobile device, tap Settings > Wi-Fi, and connect to the default network SSID shown on the product label on the bottom side of the router. Alternatively, scan the QR code on the product label to connect to the default network SSID.
   • Launch the ASUS Router App and follow the on-screen instructions to complete the setup.

   Setup via Web Browser:

   • Connect your PC to a LAN port at the back of the router using an additional network cable.
   • Open a web browser. You will be redirected to the ASUS Setup Wizard. If not, navigate to http://router.asus.com.
   • Follow the instructions to complete the setup.

Link Aggregation Setup Steps

1. 01 Prepare your Router

   Use Ethernet cables to connect your client to the LAN1 and LAN2 ports of TUF-AX4200. Note: The client connected to TUF-AX4200 must support Link Aggregation Control Protocol (LACP).

2. 02 Log in and Configure

   On your web browser, enter http://router.asus.com and log into the web GUI.

   From the navigation panel, go to LAN > Switch Control > Bonding/Link aggregation and select Enable. When done, click Apply.

   Note: Ensure that the Link Aggregation function of the client (e.g., NAS) you connect to TUF-AX4200 is enabled.

FAQ FREQUENTLY ASKED QUESTIONS

Q1: Where can I find more information about the wireless router?

Technical support site: https://www.asus.com/support

Customer hotline: refer to the Networks Global Hotline Information section in this Quick Start Guide.

Service and Support: https://www.asus.com/support

Video Tutorials: https://qr.asus.com/wl_videotutorials

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs are part of a commitment to environmental protection. For detailed recycling information in different regions, please visit http://csr.asus.com/english/Takeback.htm.

REACH

In compliance with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, chemical substances in ASUS products are published on the ASUS REACH website: http://csr.asus.com/english/REACH.htm.

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Prohibition of Co-location: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. This device is restricted for indoor use.

WARNING! This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 50cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

CAN ICES-003(B)/NMB-003(B)

Radio Frequency (RF) Exposure Information: The radiated output power of the ASUS Wireless Device is below the Innovation, Science and Economic Development Canada radio frequency exposure limits. The ASUS Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized.

This equipment should be installed and operated with a minimum distance of 31cm between the radiator and any part of your body.

This device has been certified for use in Canada. Status of the listing in the Innovation, Science and Economic Development Canada's REL (Radio Equipment List) can be found at: http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html

Additional Canadian information on RF exposure can be found at: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

NCC 警語

低功率射頻器材技術規範

「取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。」

* 應避免影響附近雷達系統之操作。

「產品之限用物質含有情況」之相關資訊,請參考下表:

備考1.“○”係指該項限用物質之百分比含量未超出百分比含量基準值。

備考2.“-”係指該項限用物質為排除項目。

DFS 警語

操作在5.15-5.35/5.47-5.85GHz之無線資訊傳輸設備(802.11a/ac產品),應避免影響附近雷達系統之操作。

Safety Notices

• Use this product in environments with ambient temperatures between 0°C (32°F) and 40°C(104°F).
• Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
• DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
• DO NOT place or drop objects on top and do not shove any foreign objects into the product.
• DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
• DO NOT cover the vents on the product to prevent the system from getting overheated.
• DO NOT use damaged power cords, accessories, or other peripherals.
• If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• DO NOT mount this equipment higher than 2 meters.

Consignes de sécurité

• Utilisez ce produit dans un environnement dont la température ambiante est comprise entre 0°C (32°F) et 40°C (104°F).
• Référez-vous à l'étiquette située au dessous du produit pour vérifier que l'adaptateur secteur répond aux exigences de tension.
• NE PAS placer sur une surface irrégulière ou instable. Contactez le service après-vente si le châssis a été endommagé.
• NE PAS placer, faire tomber ou insérer d'objets sur/dans le produit.
• NE PAS exposer l'appareil à la pluie ou à l'humidité, tenez-le à distance des liquides. NE PAS utiliser le modem lors d'un orage.
• NE PAS bloquer les ouvertures destinées à la ventilation du système pour éviter que celui-ci ne surchauffe.
• NE PAS utiliser de cordons d'alimentation, d'accessoires ou autres périphériques endommagés.
• Si l'adaptateur est endommagé, n'essayez pas de le réparer vous-même. Contactez un technicien électrique qualifié ou votre revendeur.
• Pour éviter tout risque de choc électrique, débranchez le câble d'alimentation de la prise électrique avant de toucher au système.
• NE PAS placer cet équipement à une hauteur supérieure à 2 mètres.