JONATHAN Y JYL2401A Pendant Light
Model#: JYL2401A
Product Dimensions: 8.25"L X 8.25"W X 13.5-72.5"H
Important Warnings
WARNING: Installation of this lighting fixture should be performed by a licensed electrician.
WARNING: Switch off the main electrical supply from the main fuse box/circuit breaker before installation.
Inspect the item carefully before attempting to install. If there is any damage or obvious defect, do not install. The item may not be returned once it has been installed.
Care and Maintenance
To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface.
To clean the inside of the fixture, first disconnect power by turning off the circuit breaker or removing the fuse. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface.
Do not use cleaners with chemicals, solvents, or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
Notice & Important Safety Instructions
- Please ensure you have all parts indicated before beginning assembly.
- Assemble this item on a soft surface to prevent scratching the finish.
- To reduce the risk of fire, electrical shock, or injury, follow the guidelines below for safe use and installation.
- The external flexible cable or cord of this lamp cannot be replaced. If the cord is damaged, the lamp shall be destroyed.
Part List and Hardware List
| Piece | Description | Quantity | Piece | Description | Quantity |
|---|---|---|---|---|---|
| A | Mounting Bracket [Diagram: Metal bracket] | 1X | I | Adjust the ring ring [Diagram: Metal ring] | 1X |
| B | Mounting screw [Diagram: Screw] | 2X | J | Chain [Diagram: Metal chain links] | 1X |
| C | Ground screw [Diagram: Green screw] | 1X | K | Hand ring [Diagram: Ring with a loop] | 1X |
| D | Wire connector [Diagram: Plastic wire connector] | 3X | L | Bulb [Diagram: Light bulb shape] | 1X |
| E | Tube [Diagram: Cylindrical tube] | 1X | M | Socket [Diagram: Light bulb socket] | 1X |
| F | Adjust the ring [Diagram: Ring with threaded part] | 1X | N | Glass [Diagram: Glass shade] | 1X |
| G | Canopy [Diagram: Decorative ceiling plate] | 1X | O | Plate [Diagram: Flat plate] | 1X |
| H | Adjustable buckle [Diagram: Buckle or clip] | 2X | P | Screws [Diagram: Small screws] | 3X |
Preparation
Before beginning assembly, ensure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
Assembly Instructions
- Fix the mounting bracket (A) to the outlet box with mounting screw (B).
- Pass the fixture wires through the chain (J) and the adjust the ring (F).
- Make wire connections using wire connectors (D), following the reference chart below:
Connect, Hot, Black or Red Outlet Supply Wire to: Connect, Neutral, White Outlet Supply Wire to: Black
* Parallel Cord (round & smooth)White
* Parallel Cord (square & ridged)Clear, Brown, Gold or Black without Tracer (colored stripes) Clear, Brown, Gold or Black with Tracer (colored stripes) Insulated Wire (not green) with copper metal conductor Insulated Wire (not green) with Silver metal conductor. *Note: When parallel wire (SPT I & SPT II) is used, the neutral wire is square shaped and ridged, and the hot wire will be round and smooth.
- Grounding Instructions:
- For installation in the United States: Wrap the ground wire from the outlet box around the green ground screw (C) on the mounting bracket, ensuring at least 2 inches from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect it to the outlet ground wire using a wire connector.
- For installation in Canada: If the fixture is supplied with a ground wire, wrap the ground wire around the green grounding screw on the mounting bracket. Tighten the ground screw.
- Insert the adjust the ring (F) into the tube (E).
- Fix the chain (J) to the adjust the ring (F) using the adjustable buckle (H).
- Fix the canopy (G) to the adjust the ring (F) using the adjust the ring ring (I).
- Fix the chain (J) to the hand ring (K) using the adjustable buckle (H).
- Insert the bulb (L) into the socket (M).
- Fix the glass (N) to the plate (O) using 3 screws (P).
Bulb Information
Please use Type "A" bulb, max 40-watt, or CFL bulb, max 13-watt, or LED bulb, max 9-watt.
One 4-watt LED bulb is included in the box.
