Introduction
This document provides instructions for setting up and using the ONE FOR ALL URC6420 universal remote control. It covers various setup methods, including SimpleSet, Auto Search, and Direct Code Setup, to configure your remote for different devices.
Getting Started: Region Selection
Follow these steps to select your region:
- Select your region. If you live in France, set the remote to ( F ). If you live in another country (outside Great Britain/Ireland, Germany, France, Spain, or Italy), such as Switzerland or Belgium, set the remote to INT.
- Insert batteries to activate the selected region.
- Check if your device brand is listed in the corresponding section.
Regions:
- F: France
- INT: All Other Countries (Outside Great Britain / Ireland, Germany, France, Spain, or Italy)
(See original document for detailed language-specific instructions for region selection.)
Setup Methods
The URC6420 offers three primary methods for setting up your remote:
1. SimpleSet Mode
This mode configures the most common device brands quickly. Locate the numeric key associated with your brand and follow the steps.
Steps:
- Hold down the ? (green) and ? (yellow) buttons for 3 seconds. The LED will blink twice ??.
- Ensure the device you want to control is switched on (not in standby).
- Point the remote at the device.
- Hold down the numeric key associated with your brand (e.g., Metronic = 4) until the device turns off. This may take up to 40 seconds.
- Release the numeric key as soon as the device turns off.
READY!
Troubleshooting: If the device does not turn off or back on, refer to the Auto Search method.
2. Auto Search Mode
Use this mode for device brands not supported by SimpleSet. The remote will automatically search for compatible codes.
Steps:
- Hold down the ? (green) and ? (yellow) buttons for 3 seconds. The LED will blink twice ??.
- Press the OK button once. The LED will blink twice ??.
- Ensure the device is switched on (not in standby).
- Point the remote at the device. The remote will send power-on signals every 3 seconds.
- Press OK once the device turns off (within 3 seconds).
READY!
Troubleshooting: If the device turns off but not back on, you may have pressed OK too late. Repeat the process. If the remote doesn't function correctly, try Auto Search again or use the COPY function.
3. Direct Code Setup
If SimpleSet or Auto Search is unsuccessful, try Direct Code Setup. You will need to find the 4-digit code for your specific device and brand.
Steps:
- For Digital TV Receiver: Press and hold ? (green) and ? (yellow) for 3 seconds. The LED blinks twice ??.
- For Main TV Control: Press and hold ? (red) and ? (blue) for 3 seconds. The LED blinks twice ??.
- Enter the 4-digit code for your device.
- Ensure your device is switched ON (not on standby).
Verification: Pressing the POWER button should turn your device off. If not all keys work or the device doesn't turn off, repeat the steps with the next code for your brand.
TV Main Control
You can program the remote to control your TV's volume, power, and input.
- If your TV brand is listed in your region (see page 15), follow SimpleSet steps (A & B): Step A: Hold ? (red) and ? (blue) for 3 seconds. Step B: Hold the numeric key for your TV brand.
- If your TV brand is NOT listed (see page 14), follow Auto Search steps (A & C): Step A: Hold ? (red) and ? (blue) for 3 seconds.
Learning (COPY) Function
This function allows you to copy functions from your original remote to the ONE FOR ALL remote.
Steps:
- Align the two remotes, pointing the IR emitters towards each other (2-5 cm apart).
- Hold down the COPY button for 3 seconds. The two LEDs blink twice ??.
- Press the button on the original remote you wish to copy (e.g., 'I/II' for mono/stereo).
- Then, press and hold the target button on the ONE FOR ALL remote (e.g., the red button) until the LEDs blink twice ??, confirming the copy.
READY!
You can copy other functions by repeating step 4. All buttons can be copied except the COPY button itself.
To delete a copied function, hold COPY for 3 seconds, then press the target button for 3 seconds until LEDs blink twice, then hold COPY again for 3 seconds.
Device Categories
The remote can control the following types of devices:
- TV: Television / HDTV / LCD / LED / Plasma / Projector / Rear Projector
- SAT: Satellite Receiver / Set-Top-Box / DVB-S / DVB-T / Digital Terrestrial / Freeview / SAT/HDD
- CBL: Cable Converter / Set-Top-Box / IPTV / DVB-C
Device Code Lists
The document includes extensive code lists for programming the remote control for various brands of TV, SAT receivers, and CBL devices. These lists are organized by device type and brand, providing 4-digit codes for direct code setup. Due to their extensive nature, the full lists are not reproduced here, but they are available in the original document for specific device and brand lookups.
