Quick Guide: JUNG ZigBee Wall and Handheld Transmitter

Manufacturer Information

Albrecht Jung GmbH & Co.KG

Volmestraße 1

58579 Schalksmühle

Email: kundencenter@jung.de

Website: www.jung.de

Documentation Date: 13.04.18

1. ZigBee Compatibility List

1.1 Hue Components

The following Philips Hue components are compatible with the JUNG ZigBee transmitter.

1.2 dresden elektronik Components

The following dresden elektronik components are compatible with the JUNG ZigBee transmitter.

1.3 Innr lighting Components

The following Innr lighting components are compatible with the JUNG ZigBee transmitter.

2. Integration with Philips Hue Bridge

2.1 Adding Light Sources

To integrate light sources via the Hue Bridge, follow the instructions in the "Quick Guide Philips Hue".

2.2 Opening Philips Hue App and Searching for Devices

Follow these steps:

• Open the Philips Hue App.
• Navigate to: Settings > Lamp settings.
• Tap "Search".

If you encounter issues finding your lamps, enter the six-digit serial number of the lamp before tapping Search.

2.3 Adding Transmitters

Press the indicated buttons on the transmitter for approximately 5 seconds until the LEDs on the transmitter blink.

ATTENTION: The transmitter will not appear in the Philips App afterwards.

2.4 Connecting Transmitter to a Light

Approach the desired light source within 10-50 cm and press the indicated buttons on the transmitter for approximately 5 seconds until the LEDs blink.

2.5 Switching Lights On/Off/Dimming

• On/Off: Short press button 0 or I.
• Dimming: Long press button 0 or I until the desired brightness is reached.

2.6 Selecting Light Mood

Follow these steps:

• Open the Philips Hue App.
• Select: Home > Your Room.
• Choose your desired color tone and then the brightness.

2.7 Saving and Recalling Light Moods

• Recall Scene: Short press buttons 1-6.
• Save Scene: Long press buttons 1-6 until the LEDs on the transmitter blink.

3. Integration with dresden elektronik (deCONZ)

3.1 Adding Light Sources

Integrate light sources via the "ConBee" Gateway.

3.2 Installing and Opening dresden elektronik 'deCONZ' Software

Download and install the software: Software dresden elektronik "deCONZ" (Link placeholder).

Refer to the User Manual "deCONZ" (Link placeholder).

Connect the "deCONZ" Software and the USB Gateway "ConBee".

3.3 Configuring 'ConBee' USB Gateway and Creating Network

Set up the "ConBee" Device (Blue) as "Coordinator" in "deCONZ" Network Settings. Open the dresden elektronik WebApp; the "deCONZ" window appears at the top right.

3.4 Scanning for Lights/Devices and Integrating into ZigBee Network

In the WebApp: Navigate to Menu > Settings > Scan for Devices.

Open the network and allow ZigBee devices to join.

Refer to the "Quick Start Guide Wireless Light Control" for more details.

The ZigBee lights and gateway network view is displayed in "deCONZ".

Device Color Key: Blue: Coordinator / Controller (Gateway), Yellow: Router / Light.

3.5 Adding Transmitters

Press the indicated buttons on the transmitter for approximately 5 seconds until the LEDs on the transmitter blink.

3.6 JUNG ZigBee Wall/Handheld Transmitter, Lights, and Gateway Network View

JUNG ZigBee Wall/Handheld Transmitters appear in the network visualization.

Device Color Key: Grey: End-Device.

3.7 Connecting Transmitter to a Light

Approach the desired light source within 10-50 cm and press the indicated buttons on the transmitter for approximately 5 seconds until the LEDs blink.

3.8 Light On/Off/Dimming

• On/Off: Short press button 0 or I.
• Dimming: Long press button 0 or I until the desired brightness is reached.

3.9 Selecting Light Mood

Select the light > Set desired color values or light effects. Save to JUNG ZigBee Wall/Handheld Transmitter (see next section).

3.10 Saving and Recalling Light Moods

• Recall Scene: Short press buttons 1-6.
• Save Scene: Long press buttons 1-6 until the LEDs on the transmitter blink.

4. FAQ List

4.1 Transmitter Not Switching Lamp After New Transmitter Added

Prerequisite: Both transmitters must be in the same network (cf. BDA - 4.3).

Behavior: If not, the existing connection is "stolen".

Solution: Connection to a lamp can only be established after both transmitters are in the same network.

4.2 Lamp Not Controllable via App After New Transmitter Added

Prerequisite: Transmitter must be in the same network as the Bridge/Gateway (cf. BDA - 4.1).

Behavior: If not, the connection to the Bridge/Gateway is "stolen".

Solution: Connection to a lamp can only be established after the Bridge/Gateway and the transmitter are in the same network.

4.3 Lights Not Responding to Commands with Osram Lightify Gateway

Prerequisites:

• Using Osram Lightify Gateway (WLAN Version: 1.1.2.107, ZigBee Version: 1.2.0.67).
• Switching lights off via conventional switch.

Behavior:

• All lights (regardless of manufacturer) can no longer be operated by the transmitter.
• Lightify Gateway ignores third-party connections.

Solution: Lights must not be switched off via a conventional switch when using the Lightify Gateway with the specified software version.

4.4 Cannot Pair More Lights to Transmitter

Prerequisite: 10 lamps already paired.

Behavior: Attempting to pair an 11th lamp fails.

Solution: A connection from the transmitter to a lamp must be deleted first (cf. BDA - 4.6).

4.5 Transmitter Partially Unpairable to Philips Bridge via Android App

Prerequisite: Setup via an Android device for the Philips Hue Bridge.

Behavior: The Android Philips hue App (Version 1.11.1.0) has an issue where a new "automatic search" does not open the network.

Solution: Before starting a new "automatic search", exit the Settings menu. Then, a connection can be established again (cf. BDA - 4.1).

4.6 Existing Transmitter Blinks Red When Adding New One (New One Green)

Behavior: This occurs when lamps refuse positive feedback (blink green) (End Device Capacity). If the new transmitter blinks green, the process was successful. The red LED on the existing transmitter can be ignored. This can also happen when adding to Philips Bridge or Osram Gateway.

Solution: Reset ZigBee lights using buttons 1 + 2 and repeat the pairing process.

4.7 No Communication Between Transmitter and Lights

Behavior: In rare cases, connection problems can be caused by excessive data traffic in the wireless network (e.g., WLAN router).

Solution: Manually change the ZigBee channel.

• Philips hue (Version 1.11.1.0): Open Hue App > Settings > Hue bridges > Select Bridge > ZigBee > Change Channel. (Note: All lamps must be on. Process takes approx. 30 seconds).
• Osram Lightify (Version v1.6.0): ZigBee channel cannot be manually changed.
• Direct communication (Sender and Lamp, no Bridge/Gateway): ZigBee channel cannot be manually changed.

4.8 Saved Scene Not Executed by Light

Behavior: The number of scenes per light is limited. Once this limit is reached, further scenes are learned by the transmitter but ignored by the light.

Solution: As of 07.06.2016: Philips hue supports 90 scenes per lamp; Osram Lightify supports 15 scenes per lamp. Reset lights via transmitter (buttons 1+2) and re-add to the bridge.

4.9 Osram Lights Not Transferred When Migrating ZigBee Participants from Sender A to Sender B

Behavior: With the current version (Release 10.02.32.02), transferring lights is NOT possible (cf. BDA Hand/Wandsender 5.5). This is planned to be fixed in a future release.

Solution: None.