1. Appearance
- 1. Test/Silence Button
- 2. Alarm/Test/Signal Indicator
- 3. Tamper Switch
- 4. Battery Holder
Scan the QR code for more information and operation help.
2. Enrollment
Check signal strength.
3. Installation
Check signal strength. Install the detector.
The installation process involves checking signal strength and then physically installing the detector. The diagrams illustrate steps for mounting and connecting the device.
Signal Strength Test:
- Step I: [Signal Strength Test Indicator]
- Step II: [Signal strength test results, showing a sequence of pass/fail indicators]
4. Test
The device can be tested using the Test/Silence Button. The indicator light will show the status.
The diagrams show the test sequence and expected indicator behavior.
Specifications
| Detection Method | Chamber with photoelectric sensor |
| Operation Mode | Independent & wireless reporting |
| Siren Volume | ≥ 85 dB @ 3 m |
| LED indicator | Blue (alarm) |
| Operating temperature | -10 °C to 55 °C (14 °F to 131°F) |
| Storage temperature | -20 °C to 60 °C (-4 °F to 140°F) |
| Operating humidity | 10% to 90% |
| Dimension (D x D) | Ø102 × 48.4mm |
| Transmission frequency | 433 MHz |
| RF range | 800 m (free space) |
| Battery | Non Replaceable CR17450 x 1 for Main Sensor, CR123A x 1 RF Module, 3V, 10 Years Life Span |
Compliance and Safety Information
This product is designed and manufactured by Hangzhou Hikvision Digital Technology Co., Ltd.
CE Compliance:
This product is marked with "CE" and complies with harmonized European standards according to Directive 2014/53/EU (Radio Equipment), Directive 2014/30/EU (Electromagnetic Compatibility), and Directive 2011/65/EU (Restriction of Hazardous Substances).
WEEE Directive (2012/19/EU):
Products marked with this symbol must not be disposed of with unsorted municipal waste in the EU. Recycle products by returning them to your local supplier or designated collection points. More information: www.recyclethis.info.
Battery Directive (2006/66/ES):
This product contains batteries that must not be disposed of with unsorted municipal waste in the EU. Battery information is in the product documentation. Batteries are marked with symbols, potentially including letters for Cadmium (Cd), Lead (Pb), or Mercury (Hg). Recycle batteries by returning them to your supplier or designated collection points. More information: www.recyclethis.info.
Battery Warning:
- Risk of explosion if battery is replaced by an incorrect type.
- Do not attempt to recharge, disassemble, heat above 100°C (212°F), or incinerate the battery.
- Do not swallow battery. May cause severe or fatal internal burns in as little as 2 hours.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- Seek immediate medical attention if batteries are swallowed or placed inside any part of the body.
Installation Warning:
The force exerted on the device shall be three times the weight of the device but not less than 50 N. The device and its associated mounting means must be firmly secured. After installation, there shall be no damage to the device or the mounting plate.
FCC Information:
This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
FCC Conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
