AQQA AQ165 USER MANUAL

Product Overview

The AQQA hang-on-back aquarium filter is an external filter designed for aquariums. It features a highly efficient filtration system with a bio-wheel design. The integrated floating skimmer effectively removes surface debris, and a copper motor ensures quiet operation. Ensure sufficient water is added to the filter before initial use; no additional water is needed when the motor restarts. The filter utilizes a three-layer cartridge for ample filter media, and its flow rate is adjustable. This multi-functional filter is suitable for planted tanks, aquariums, and shrimp tanks.

1. PRODUCT FEATURES

• Filter chamber allows for flexible use of different filter media.
• Smooth running with vibration-damping support that absorbs pump vibrations.
• Activated carbon sponge insert filters suspended particles, provides a colonization surface for beneficial bacteria, and stabilizes water quality.
• Bio-wheel design ensures quieter operation and increases oxygen supply in the aquarium.
• All-copper motor water pump for a longer service life.
• Adjustable flow rate at the water inlet.
• Suitable for aquariums with glass thickness up to 0.66 inches (17MM).

2. PRODUCT SPECIFICATIONS

3. PRODUCT DIAGRAM

Product components:

• Top cover
• Flow regulator
• Rubber ring
• T-shaped inlet tube
• Filter chamber
• Bio-wheel
• Filter body
• Support foot
• L-shaped outlet tube
• Rubber ring
• Floating skimmer
• Extension pipe
• Water Inlet tube
• Water pump

A diagram illustrates the assembly of these components.

4. INSTALLATION DIAGRAM

1. Open the packaging and check accessories for completeness.
2. Assembly steps:
   • Connect the water inlet tube to the T-shaped inlet tube.
   • Install the floating skimmer to the T-shaped inlet tube, ensuring the side connector is aligned.
   • Connect the assembled parts to the L-shaped outlet tube.
   • Insert the flow regulator into the L-shaped outlet tube.
   • Assemble the bio-wheel and L-shaped outlet tube into the filter.
   • Cover with the top cover.
3. Hang the filter on the aquarium glass and adjust the support foot. The maximum width for the fish tank is 17MM. The support foot adjusts the filter width. Ensure the pipe is completely submerged in water.
4. Set the flow regulator to the highest flow rate, add water to the filter, and connect to the mains.
5. To remove the upper filter basket, hold the connecting tube firmly and pull upwards.

5. ATTENTIONS

• Read this user manual carefully before use and follow instructions strictly.
• Keep the power supply away from water as it is not waterproof.
• Keep the filter away from flammable items to avoid accidents.
• Unplug the power and contact the seller if the filter is not working properly. Opening the unit will void the warranty.
• Unplug the power before maintenance.
• The operating temperature range for the filter is between 40°F ~95°F (4°C~35°C).

6. TROUBLESHOOTING

7. ATTENTIONS

• Please read this user manual carefully before using and follow it strictly.
• Please keep the power supply away from water since it is not waterproof.
• Please keep the filter away from flammable items to avoid accidents.
• Please unplug the power and contact the seller if the filter is not working properly.
• Please unplug the power before maintenance.
• Please mind that the operating temperature range for the filter is between 40°F ~95°F (4°C~35°C).

8. WARNING

To avoid possible electric shock, do not immerse the switch in water. If the switch falls into water or becomes wet, do not touch it until unplugged. Basic safety precautions:

1. Read and follow this user manual strictly.
2. DANGER: To avoid possible electric shock, take special care as water is used with aquarium equipment. For the following situations, do not attempt to repair yourself. Instead, return the filter to an authorized service facility for maintenance or discard it.
   • A. If the appliance falls into water, DO NOT touch it. First unplug it, then retrieve it. If electrical components get wet, unplug immediately.
   • B. Carefully examine the filter after installation. It should not be plugged in if water is on parts not intended to be wet.
   • C. Do not operate the filter if it has a damaged cord or plug, is malfunctioning, dropped, or damaged. The power cord cannot be replaced. If damaged, the filter should be discarded.
   • D. To prevent the filter plug from getting wet, position the aquarium and its stand to one side of a wall-mounted outlet to prevent water from dripping onto the outlet or plug. A "drip loop" should be arranged for each cord connecting the filter to the outlet. If an extension cord is used, the "drip loop" prevents water from traveling along the cord to the outlet. If the plug or outlet gets wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker supplying power. Then, unplug and examine the outlet for water. Consult an electrician if unsure.
3. Close supervision is necessary when the filter is used near children.
4. This filter is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised or instructed by a person responsible for their safety.
5. To avoid injury, do not contact moving or hot parts.
6. Always unplug the filter from the outlet when not in use, before putting on or taking off parts, maintenance, or placing hands in water. Never yank the cord to pull the plug; grasp the plug and pull to disconnect.
7. Do not use the filter for other than its intended use. Attachments not recommended or sold by the manufacturer may cause unsafe conditions and void the warranty.
8. Do not install or store the filter where it will be exposed to extreme weather or temperatures below freezing.
9. Ensure the filter is securely installed before operating.
10. Read and observe all important notices on the filter.
11. If an extension cord is necessary, use one with a proper rating (amperes or watts). A cord rated for fewer amperes or watts than the filter may overheat. Arrange the cord to prevent tripping or pulling.
12. The filter is intended for HOUSEHOLD USE ONLY.
13. SAVE THIS USER MANUAL.

9. AQQA LIMITED MANUFACTURER'S WARRANTY

AQQA offers a 2-year manufacturer warranty from the date of sale for products purchased from an AQQA®-authorized specialist dealer. Retain your receipt for future warranty claims. Products are guaranteed by AQQA® Aquatic Supplies against defective material and workmanship under normal use for up to 2 years from the original purchase date through an Authorized Dealer.

Products have no warranty if:

• The product has been serviced, modified, or tampered with by anyone other than AQQA® Aquatic Supplies.
• The product has been abused or damaged (including broken or cracked bulbs), and/or transported without proper packaging.
• The product was purchased from an Unauthorized Reseller.

WARRANTY LIABILITY DISCLAIMER

AQQA® is not liable for any consequential or incidental damages, including but not limited to, lost aquatic life, personal injury, property damage, equipment damage, lost profits, lost wages, lost savings, or lost income, arising from the use of any AQQA® products.

1.0. Terms and Conditions of Warranty:

• AQQA® warrants to the purchaser, for 2 years from the original purchase date through an Authorized AQQA® Reseller, to repair or replace parts found to be defective due to materials or workmanship, provided the goods do not operate as instructed.
• All claims for repair or replacement must be made at the place of purchase.
• Only the direct purchaser is entitled to warranty claims and these are not transferable without AQQA®'s consent.
• The original and dated Proof of Purchase (receipt) must accompany all claims. Provide this Guarantee where possible.
• Wear parts (e.g., seals, suction devices, axes, pump wheels, light sources, pH electrodes, filter media like cartridges, as well as UVC burners), glass damage, product opening, or use of non-AQQA® original parts are excluded from the guarantee.
• Goods for warranty claims should be prepared for transportation in original or comparable packaging. AQQA® will not cover shipment costs.
• If inspection reveals goods are in normal working order, AQQA® may request reimbursement of reasonable costs incurred.
• Warranty claims do not apply to insignificant deviations from agreed or customary condition or usability (e.g., minor deviations in color, dimensions, quality, or performance).
• AQQA®'s warranty obligation extends only to the delivery of newly manufactured products. Used products are sold as-is unless otherwise agreed.

10. DISPOSAL

Do not dispose of this product as unsorted municipal waste. It must be disposed of at an authorized recycling facility for electrical and electronic appliances. Recycling waste helps save natural resources. Consult your local seller for environmentally friendly disposal methods.

11. PACKING LIST

• 1x Top Cover
• 1x Flow regulator
• 1x Rubber ring
• 1x T-shaped inlet tube
• 1x Filter Chamber
• 1x Filter body
• 1x Water pump
• 1x Water Inlet tube
• 1x Extension pipe
• 1x Floating skimmer
• 1x Rubber ring
• 1x L-shaped outlet tube
• 1x User manual
• 1x Bio-wheel (FK063-S/FK063-M)
• 2x Bio-wheel (FK063-L)
• 1x Support foot (FK063-S/FK063-M)
• 2x Support foot (FK063-L)
• 1x Foam protection for water inlet

12. CONTACT INFORMATION

Company Name: Shenzhen Aiku Pet Technology Co., Ltd

Address: Room 501, No.20, Lane 1, Lishipai, Dafapu Community, Bantian Street, Longgang District, Shenzhen Guangdong. 518000

Email: service@aqqapet.com

Website: http://www.aqqapet.com

f  ▶️ @AQQA Aquarium

European Representative

Company Name: E-CrossStu GmbH

Address: Mainzer Landstr.69, 60329 Frankfurt am Main

E-mail: E-CrossStu@web.de

Tel: +49 69332967674

EC REP CE UKCA [crossed-out-wheeled-bin] [recycling-symbol] [waste-electrical-electronic-equipment]

MADE IN CHINA