Remote controller User Manual

Points For Attention

1. Install two AAA batteries correctly.
2. When the battery has no power, it should be replaced with the same type of battery. Battery model: AAA 1.5V *2.
3. Ambient temperature: -5 °C~45 °C.
4. Remote control distance: >8m
5. Communication mode: Bluetooth 2.4GHz.

Binding And Unbinding

How to bind the remote control to the device?

Bind OPERATIONS:

1. Make sure the remote control works. Turn off 2 bulbs by switch (not remote control).
2. Remove Bulb 2, turn on Bulb 1 by push switch, long press (Group 1 open) until Bulb 1 flashed 3 times, proving that Bulb 1 pairing to Group 1 is successfully. Perform the long press for about 5 seconds once Bulb 1 is powered on ASAP!

Figure 1

Figure 2

Repeat step 1, put on the unpaired Bulb 2, then turn on the 2 bulbs by push switch, long press (Group 2 open) until Bulb 1 flashed 3 times, proving that Bulb 1 pairing to Group 1 is successfully. Perform the long press for 5 seconds once Bulb 2 is powered on ASAP!

How to unbind?

Unbind OPERATIONS:

1. Make sure the remote control works. Turn off 2 bulbs by switch (not remote control).
2. Turn on the 2 bulbs by push switch, press (Group 1 open) 8 times continuously until Bulb 1 flashed 5 times, proving that the unpairing to Group 1 is successfully. Perform the continuously press once Bulb 1 is powered on ASAP!
3. Repeat step 1, remove the cleared Bulb 1, then turn on the Bulb 2 by push switch, press (Group 2 open) 8 times continuously until Bulb 2 flashed 5 times, proving that the unpairing to Group 2 is successfully. Perform the continuously press once Bulb 2 is powered on ASAP!

How to use a single remote to control two lamps?

1. Unbind 2 bulbs in Lamp 1. Take out Remote control 1, unbind Bulb 1 in Lamp 1. Unscrew Bulb 1 and unbind Bulb 2. Tighten all the bulbs when complete unbound.
2. Bind 2 bulbs of Lamp 1 with Group 1 in Remote control 1 at the same time.
3. Bind 2 bulbs of Lamp 2 with Group 2 in Remote control 2 at the same time.
4. Finish! You can use Remote control 1 to control 2 lamps, Group 1 controls Lamp 1, and Group 2 controls Lamp 2.

Attention: Lamp 2 can still be controlled by Remote control 2, it is recommended to put it away to avoid confusion.

White Light Mode

1. In the white light state, the brightness and color temperature can be adjusted by pressing the key (brightness + brightness - color temperature + color temperature -) (Figure 3)
2. In the colorful static mode or colorful dynamic mode, long press the (colorful dynamic mode) key (Figure 4) to exit the colorful light mode and change to white light.

Figure 3

Figure 4

Colorful Static Mode

In the colorful static mode, you can adjust the brightness and color by pressing the key (brightness + brightness - mode + mode -) (Figure 3)

Colorful Dynamic Mode

In the colorful dynamic mode, you can adjust the speed and mode by pressing the key (speed + speed - mode + mode -) (Figure 3)

Count Down

1. Countdown for 30 minutes: in the light on state, press the (countdown for 30 minutes) button for 30 minutes and then turn off the light; in the light off state, press the (countdown for 30 minutes) button for 30 minutes and then turn on the light.
2. Countdown 60 minutes: in the light on state, press the (countdown 60 minutes) button for 60 minutes and then turn off the light; in the light off state, press the (countdown 60 minutes) button for 60 minutes and then turn on the light (Figure 5)

Figure 5

Key Description

• ○ Turn on or off
• ● Close all bound devices
• + Brightness increases, speed increases
• - Brightness decreases, speed decreases
• ◆ On the left is the color temperature increase or the forward mode. On the right is the color temperature reduction or the backward mode
• ◇ Colorful static mode
• ◈ Colorful dynamic mode
• ◉ Group 1 open
• ◊ Group 1 off
• ○ Group 2 open
• ◌ Group 2 off
• ◍ Countdown 30 minutes
• ◎ Countdown 60 minutes