Miele PFD 104 SCVi Dishwasher Installation Plan

This document provides a comprehensive installation plan for the Miele PFD 104 SCVi dishwasher. It includes essential information regarding installation requirements, dimensions, connections, technical data, and operating conditions to ensure a safe and proper setup.

Installation Notes

For safe installation and commissioning, please refer to this installation plan, the service documentation, the installation sheet, and the operating instructions. This plan details the appliance's dimensions, technical data, and site requirements.

Installation Requirements:

The dishwasher must be installed and commissioned by Miele Customer Service, an authorized Miele dealer, or a qualified specialist.
Installation must comply with valid regulations, standards, and health and safety codes.

Environmental Requirements:

Ensure furniture and fittings in the room are suitable for the environment, as condensate may build up around the dishwasher.
A vapour barrier film is supplied to protect the worktop from steam damage. Attach this film above the door, underneath the worktop.

Electrical Connection:

All electrical work must be performed by Miele Customer Service, an authorized Miele dealer, or a qualified electrician.
The dishwasher should be connected via a suitably rated plug and socket.
If hard-wired, a power switch with a contact gap of at least 3 mm must be installed on site, disconnecting the dishwasher at all poles. This must be incorporated into the fixed wiring according to AS/NZS 3000.
The socket and power switch must remain accessible after installation for safety testing.
The connection cable must be protected from thermal damage.
For enhanced safety, a residual current device (RCD) with a 30 mA trip current is recommended.
An equipotential bonding screw connection point is located at the back of the dishwasher. Equipotential bonding should be performed if possible on site.

Water Connection:

Connect the dishwasher only to fully vented pipework. Increased water pressure can damage components.
Incoming water quality must meet the drinking water specification of the operating country.
Connect to the water supply in accordance with local and national requirements (e.g., Plumbing Code of Australia). Connection to cold or hot water is permissible; hot water may reduce program running times.
A dynamic water pressure of at least 200 kPa is required for short program running times.
Installation must adhere to AS/NZS 3500.1 and AS/NZS 3500.2. A separate backflow prevention device (dual check valve) is supplied.

Installation Requirements (Water Inlet):

Install the supplied dual check valve between the tap and the water inlet hose.
Screw the dual check valve onto the tap, then screw the water inlet hose with the water protection system onto the dual check valve thread.
Gradually turn on the tap to test for leaks. If leaks occur, ensure the connection is secure and straight.
If a tap is unavailable, a qualified installer must connect to the mains water supply.
The tap should remain accessible for shutting off the water supply when the appliance is not in use.

Drain:

Connect the dishwasher drain hose to a separate on-site drainage system intended solely for the dishwasher. If a separate connection is unavailable, connect to a dual-chamber siphon.
If connecting directly to the drainage system, use the supplied hose clip.
The on-site connector for the drain hose can be adapted to various hose diameters. Shorten the connector if it extends more than 30 mm into the drain hose to prevent blockage.
Lay the drain hose without kinks or tension.
If the on-site drain connection is lower than the guide path for lower basket rollers, a siphoning effect may occur. In such cases, lay the drain hose with a bend so its highest point is at least level with the lower basket roller guide path.

External Dispensing:

An external dispensing module for liquid cleaning agents can be connected to the back of the dishwasher. This is an optional accessory with its own installation instructions.

Appliance Dimensions and Installation Dimensions

PFD 104 SCVi Dimensions:

A diagram shows the appliance dimensions. Key measurements include:

Width: 598 mm
Depth: 570 mm
Height: 845 mm (with adjustment up to 845+65 mm)
Minimum clearance at the side: 570 mm
Minimum clearance at the front: 35 mm
Maximum plinth return: 115 mm
Worktop clearance: ≥ 845 mm

Front Panel Dimensions:

	[mm]
Length	690-810
Thickness	16-20
Weight	5-12

Connections

Diagrams illustrate the connections on the back of the appliance and on-site connections.

Connections on the back of the appliance:

Electrical connection
External dispensing, power supply connection
Equipotential bonding
Waste water
Cold or hot water
External dispensing, connection for dispensing hose sealed with a blind stopper*

* The dispenser connector is supplied with the dispensing module.

On-site connections:

Diagrams show the required clearances and connection points for electrical, water, and waste water.

Electrical connection: [Diagram showing connection point 1]
Cold or hot water connection: [Diagram showing connection point 5]
Waste water connection: [Diagram showing connection point 4]
External dispensing connections: [Diagram showing connection points 2 and 6]
Equipotential bonding: [Diagram showing connection point 3]

External Dispensing Details:

Description	Unit	Value
Max. delivery head	[m]	1.5
Length of dispenser hose, DOS module to suction lance	[m]	1.8
Length of dispenser hose, back of appliance to DOS module	[m]	2.8
Length of power cable, back of appliance to DOS module	[m]	2.8

Place the cleaning agent container on the floor next to or in an adjacent cabinet, not on top of or above the cleaning machine.

Technical Data

Dimensions and Weights:

Parameter	Unit	Value
Height	[mm]	845
Height adjustment	[mm]	65
Width	[mm]	598
Depth	[mm]	570
Depth with door open	[mm]	1205
Max. plinth return	[mm]	115
Weight	[kg]	51
Max. floor load	[N]	1000

Emission Levels:

Parameter	Unit	Value
Sound power level	[dB(A) re 1 pW]	45
Sound pressure level in the workplace	[dB(A)]	32.5

Electrical Connection:

Parameter	Unit	Value
Voltage		AC 230V
Frequency	[Hz]	50
Fuse rating	[A]	15-16
Plug		Yes
Power cable length	[m]	1.7
Power cable cross-section	[mm²]	3x1.5
Heat output	[kW]	3
Total rated load	[kW]	3.2

Water Inlet:

Parameter	Unit	Value
Max. water temperature	[°C]	60
Max. water hardness	[mmol/l]	6.5
Max. water hardness	[°dH]	36
Water connection pressure	[kPa]	50-1000
On-site threaded union (flat seal)	[inches]	3/4
Connection hose length	[m]	1.5

Drain:

Parameter	Unit	Value
Max. water temperature	[°C]	82
Drain hose length	[m]	1.5
Max. drain hose length	[m]	4
Max. delivery head	[m]	1
Max. transient flow rate	[l/min]	10
Hose inner diameter	[mm]	22
On-site hose sleeve (Ø x length)	[mm]	22 x 30

Operating Conditions:

Parameter	Unit	Value
Ambient temperature	[°C]	+5 - +40
Relative humidity: Up to 31 °C, maximum	[%]	80
Relative humidity: Linear decreasing to 40 °C	[%]	50
Max. altitude above sea level	[m]	4000

Storage and Transportation Conditions:

Parameter	Unit	Value
Ambient temperature	[°C]	-20 - +60
Relative humidity	[%]	10-85
Air pressure	[hPa]	500-1060

Min. Site Access Dimensions (including transport pallet):

Dimension	Unit	Value
Height	[mm]	970
Width	[mm]	670
Depth	[mm]	670

Contact Information

Miele Australia Pty. Ltd.

ACN 005 635 398, ABN 96 005 635 398
Melbourne: 1 Gilbert Park Drive, Knoxfield, VIC 3180
Telephone: 1300 731 411
Email: service.prof@miele.com.au
Website: www.miele.com.au/professional
Sales Email: sales@miele-professional.com.au

Miele New Zealand Limited

IRD 98 463 631
8 College Hill, Freemans Bay, Auckland 1011, New Zealand
Telephone: 0800 4 MIELE (0800 464 353)
Website: www.miele.com.au/professional
Sales Email: sales@miele-professional.com.au

Miele Global Headquarters: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany

	Miele PFD 104 SCVi Installation Plan and Technical Data This document provides detailed installation instructions and technical specifications for the Miele PFD 104 SCVi dishwasher. It covers essential information on installation requirements, dimensions, electrical and water connections, drainage, operating conditions, and safety guidelines.
	Miele PFD 103 SCI Dishwasher Installation Plan and Technical Data Comprehensive installation plan and technical specifications for the Miele PFD 103 SCI dishwasher, including dimensions, electrical and water connections, drain requirements, and operating conditions.
	Miele PFD 400 - PFD 407 Installation Plan Comprehensive installation guide for Miele PFD 400 and PFD 407 professional dishwashers, covering electrical and water connections, dimensions, and external dosing.
	Miele PFD 104 SCVI XXL Dishwasher: Features, Specifications, and Performance Detailed specifications and features of the Miele PFD 104 SCVI XXL fully integrated dishwasher, highlighting its 3D MultiFlex Tray, energy efficiency, and advanced drying technology.
	Miele PWM 908 DV/DP Washing Machine Installation Plan Comprehensive installation guide for Miele Professional washing machines, models PWM 908 DV and PWM 908 DP. Covers electrical, water, and drainage connections, dimensions, and safety requirements.
	Miele PFD 104 SCVi Commercial Dishwasher Operating Instructions Comprehensive operating instructions for the Miele PFD 104 SCVi commercial dishwasher, covering installation, operation, maintenance, and troubleshooting.
	Miele Dishwasher Rebate: Save $200 on Installation Discover Miele dishwashers and save $200 on installation with this limited-time rebate offer. Learn about qualifying models and terms and conditions for this promotion.
	Miele Dishwasher Installation Offer: Save $200 Miele offers $200 off installation with the purchase of select Miele dishwashers. Promotion valid from June 30th to October 5th, 2025. View qualifying models and rebate redemption details.