PRECISE COLLECTION RECESSED STANDARD ROUGH-IN SECTIONS SERIES ELA LCRIS
CAUTION: For safety and proper operation, read and follow instructions carefully before installation.
Parts Description
- ① Cover Can
- ② Bar Hanger Bracket (2)
- ③ Bar Hanger Bracket Screws (4)
- ④ Typical Conduit Knockout
- ⑤ Bar Hanger Locking Screw (2)
- ⑥ Alternate Mounting Holes
- ⑦ Bar Hanger (4)
- ⑧ T-Bar Clips (4)
- ⑨ Trim Ring Mounting Screw (6)
- ⑩ Trim Ring Half (2)
- ⑪ Trim Ring Mounting Holes
- ⑫ Side Flanges
- ⑬ Cup Washer
- ⑭ Green Ground Screw
- ⑮ T-Bar Clip Screws (4)
Important Safeguards
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Before wiring to power supply, turn off electricity at fuse or circuit breaker.
- Disconnect A.C. power before servicing.
- All servicing should be performed by qualified personnel.
- Consult your local building code for approved wiring and installation.
- Do not use outdoors.
- Do not mount near gas or electric heater.
- Fixture must be grounded to avoid potential electric shock.
- Equipment should be mounted in location and at heights where it will not readily be subjected to tampering by unauthorized personnel.
- The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
- Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
Installation: Rough-In Section Ceiling Mount
Note: If painting or plastering after trim ring is installed, mask mounting holes on trim. Tape provided in prepack.
Bar hangers are adjustable from 14 1/2" to 24". Reverse bar hangers 90 degrees by removing bar hanger bracket screws (3), and moving bar hanger brackets (2) and bar hangers (7) to the alternate end mounting holes (6). Reattach with bar hanger bracket screws (3). Break along the score lines of bar hangers to reduce spacing to 12".
Position the rough-in section with the end flanges (2) of the cover can (1) flush with the upper surface of the ceiling material. Secure by tightening the bar hanger locking screws (5).
Wood Joists:
Adjust bar hangers to fit against joists. Drive nailer tabs into wood. See Figure 1B.
Suspended Ceilings:
Fasten the ends of the bar hangers securely to T-bars using T-bar clips (8) and clip screws (15). See Figure 1A.
Close-In Dry Ceiling:
Cutout hole in ceiling material should not exceed 4 1/2" x 13 3/4" (max.). Note: The top of the cover can (1) may be used as a template to trace cutout onto ceiling material. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Wet Ceiling:
Do not plaster inside the plaster ring opening. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Diagram Reference: Figure 1 shows an exploded view of the rough-in section components. Figure 2 illustrates the rough-in section mounted in a ceiling, showing dimensions and part callouts. Figure 3 shows a suspended ceiling installation detail.
Installation: Rough-In Section Back Mount
Note: When back mounting, Bar hangers (7) are adjustable from 14 1/2" to 24". Position the rough-in section with the side flanges (12) of the cover can (1) flush with the inner (stud side) surface of wall material.
Wood Studs:
Adjust bar hangers to fit against studs. Secure by tightening the locking screws (5). Drive nailer tabs into wood.
Metal Studs:
Installation is the same as for wood studs except that sheet metal screws (not provided) should be used to fasten the ends of the bar hanger to the studs. These screws should have a minimum pullout rating of 30 pounds.
Back Mounting Above Doorway:
Before installing the rough-in section above a doorway, make certain that there will be adequate clearance between the bottom of the sign panel and the top of the door. See Figure 2 for sign panel dimensions.
See Figure 3 for cases where the rough-in section extends above the ceiling line (as with suspended ceilings). Allow bar hangers to be properly secured.
Close-In Dry Wall:
Cutout hole in wall material should not exceed 4 1/2" x 13 3/4" (max.). Note: The top of the cover can (1) may be used as a template to trace cutout onto wall material. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Wet Wall:
Do not plaster inside the plaster ring opening. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Note for proper fit: Position the rough-in section with the end flanges (12) of the cover can (1) flush with the upper surface of the ceiling material. Install trim ring halves (10) with their end flanges flush with the lower surface of the ceiling material. Spread the two trim ring halves (10) as far apart as possible during installation. (FIG 1)
Diagram Reference: Figure 2 illustrates the rough-in section mounted in a wall, showing dimensions and part callouts. Figure 3 shows a detail of the rough-in section extending above a suspended ceiling line.
Installation: Rough-In Section End Mount
(Requires End Mount Panel Assembly) (Ref: Fig. 1 and 4)
Remove bar hanger bracket screws (3) and relocate bar hanger brackets (2) with bar hangers (7) to alternate mounting holes (on ends of cover can) and secure using same screws. Bar hangers are adjustable from 14 1/2" to 24". Break along bar hanger score lines to reduce spacing to 12". Rough-in section may be off-centered if necessary, but bar hangers should be secured together with bar hanger locking screws (5).
Position the rough-in section with the side flanges (12) of the cover can (1) flush with the inner (stud side) surface of wall material.
Wood Studs:
Adjust bar hangers to fit against studs. Secure by tightening the locking screws (5). Drive nailer tabs into wood.
Metal Studs:
Installation is the same as for wood studs except that sheet metal screws (not provided) should be used to fasten the ends of the bar hanger to the studs. These screws should have a minimum pullout rating of 30 pounds.
Close-In Dry Wall:
Cutout hole in wall material should not exceed 4 1/2" x 13 3/4" (max.). Note: The top of the cover can (1) may be used as a template to trace cutout onto wall material. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Wet Wall:
Do not plaster inside the plaster ring opening. Install trim ring halves (10) and secure with trim ring mounting screws (9).
Diagram Reference: Figure 4 shows the rough-in section mounted to a wall stud, with part callouts.
