HYGIPLAS Multi-purpose Stem Thermometer
Instruction Manual
Safety Instructions
- Clean the probe immediately after each measurement to avoid cross contamination.
- Do not expose the appliance to temperatures over 50°C/122°F or use in ovens.
Installation
- Open the battery compartment on the bottom of the appliance.
- Insert the battery (Negative (-) terminal first).
- Pull out as much of the probe cable as required.
- Close the battery cover.
Operation
Temperature Measurement
- Press the [On/Off] button to power up the thermometer.
- Insert the probe approximately 25mm (1") into the foodstuff.
- The temperature of the foodstuff is displayed when the value remains constant.
Units of Measurement
Press and hold the [°C/°F] button for three seconds to alternate between Centigrade and Fahrenheit.
Data Hold
- Press the [HOLD] button to keep the current reading displayed.
- Press the [HOLD] button again to resume normal operation.
Maximum/Minimum Readings
The thermometer can store and display the maximum and minimum temperature readings taken since the last reset:
- Press the [MAX/MIN] button. The MAX icon flashes and the maximum temperature taken displays on the screen.
- Press the [MAX/MIN] button again. The MIN icon flashes and the minimum temperature taken displays on the screen.
- Press the button again to resume normal operation.
Note: To reset the memory turn the thermometer Off and then On again. Always reset the memory before taking new readings to ensure accuracy.
High/Low Temperature Alarm
The thermometer can sound an alarm when a set temperature range is exceeded.
- Press the [SET] button. The HI value flashes on the display.
- Press the [▲] or [▼] button until the required maximum temperature is displayed.
- Press the [SET] button to confirm. The LO value flashes on the display.
- Press the [▲] or [▼] button until the required minimum temperature is displayed.
- Press the [SET] button to confirm and return to normal operation.
- When the alarm sounds, press any button to turn it Off.
- Note: The appropriate icon on the display (HI or LO) continues to flash until the temperature returns to within the set range.
- To permanently turn the alarm Off, follow the steps above but pressing the [specific button] when the HI and LO values flash on the display.
Technical Specifications
| Temperature range | -50 to 200°C / -58 to 392°F |
| Temperature reading accuracy | ± 3°C/5.4°F between -50~-20°C/-58~-4°F ± 1°C/1.8°F between -19.9~119.9°C/-3.8~247.8°F ± 2°C/3.6°F between 120~200°C/248~392°F |
| Resolution | 0.1° over full range |
| Alarm Setting Resolution | 1° over full range |
| Temperature display refresh rate | 1 second |
| Display size | 19(h) x 48(w) mm |
| Battery | 1 x AAA 1.5v |
| Cable length | 1 metre |
| Probe size | 3.5(Ø) x 125(l) mm |
| Thermometer dimensions (h x w x d) | 116 x 78 x 28 mm |
| Ambient operating temperature | 0~50°C / 32~122°F |
Troubleshooting
If the appliance ceases to function correctly, press and hold the red [RESET] button (situated on the back of the appliance) using a pointed instrument.
Compliance
Dispose of depleted batteries in accordance with local regulations. Within the EC, there are nominated disposal points for batteries.
The [WEEE logo] on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
HYGIPLAS parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.
HYGIPLAS products have been approved to carry the following symbol: [CE]
