Sentinel Kinetic MVHR Range

Quick Installation Guide

Product Description

Sentinel Kinetic, Sentinel Kinetic F, Sentinel Kinetic Plus & Sentinel Kinetic High Flow

Units are available with the condensate drain on the right or left hand side.

Diagram showing a Sentinel Kinetic MVHR unit. Airflow paths are indicated: 'Extract from dwelling' enters the unit, 'Supply to dwelling' exits. 'From atmosphere' air enters, and 'To atmosphere' air exits. Components visible include filter access panels, a control unit, spigots for duct connections, and a condensate exit. The unit is shown in both right-handed and left-handed configurations.

Diagram showing Sentinel Kinetic F, Plus, and High Flow MVHR units. Similar to the Sentinel Kinetic, airflow is managed from the dwelling (extract), to the dwelling (supply), from the atmosphere, and to the atmosphere. Key components like filter access panels, control unit, spigots, and condensate exit are present. These models are also available in right-handed and left-handed configurations.

Feature	Specification
Power	3 Amp Switched Spur beside Unit
Controller wire	15m of 4 core cable with RJ connection on one side supplied with controller
Controller connection	RJ plug fitted to terminal board marked BMS
Volt Free Boost	Momentary boost switch from bathrooms - 2 core 0.5 to SW4 terminal
Switched Live boost	240 switch live to black wire on fly lead or LS terminal (additional relay may be required)
Condensation Drain	22mm on unit to be connected to waterless trap and 32mm waste pipe
Orientation	Right and Left hand models available (can be converted on site if required)
Spigot installation	The spigots can be position on top or side of unit

Installation Dimensions

Technical drawing illustrating the dimensions of the Sentinel Kinetic range. For the 650 Kinetic model, dimensions are approximately 650mm (height) x 550mm (width) x 456mm (depth). For the 632 Kinetic F, 285 Kinetic, and 350 Kinetic F models, dimensions are indicated as 632mm, 285mm, and 350mm respectively for one dimension, with other dimensions shown as 550mm (width) and 456mm (depth). Spigot connections are shown with a diameter of Ø125mm.

Technical drawing showing the dimensions for the Sentinel Kinetic Plus and Sentinel Kinetic High Flow models. Key dimensions include approximately 745mm (height) x 524mm (width) x 776mm (depth). Specific internal dimensions and spigot positions are marked, with spigot diameters of Ø150mm for the Kinetic Plus and Ø180mm for the Kinetic High Flow.

Wiring Diagrams

Option 1: Mains Voltage Boost Switch Diagram

Wiring diagram for Option 1: Mains Voltage Boost Switch. It illustrates the connection of a 'Hard Wired Controller' to the unit's 'BMS' port. A 'Boost Switch' is connected via a 'Supply Spur' (3 AMP) and a connection block. The diagram details wiring for Live (L), Neutral (N), Earth (E), and Switched Live (LS) using specific cable types (e.g., Min 1.0mm²). An alternative wiring configuration without a 3-pole isolator is also shown, emphasizing mains voltage connections.

Option 2: Low Voltage Boost Switch Diagram

Wiring diagram for Option 2: Low Voltage Boost Switch. This shows the 'Hard Wired Controller' connected to the unit's 'BMS' port. A 'Boost Switch' is wired to the unit's 'SW4 connection' using recommended 0.5mm² or alarm cable (4 core twined). A 'Supply Spur' (3 AMP) provides power. The diagram highlights that all low voltage boost switches connect exclusively to the SW4 terminal.

Contact Information

BPC Ventilation Ltd
8 Redlands Road
Larne
BT40 1AX
T: 028 2827 5150
E: info@bpcventilation.com
W: www.bpcventilation.com

	Vent-Axia Sentinel Kinetic MVHR Installation and Commissioning Guide Comprehensive guide for installing and commissioning Vent-Axia Sentinel Kinetic Mechanical Ventilation with Heat Recovery (MVHR) units, covering safety, technical data, and operational setup for residential properties.
	Vent-Axia Lo-Carbon Sentinel Kinetic High Flow MVHR System Information on the Vent-Axia Lo-Carbon Sentinel Kinetic High Flow, a mechanical ventilation with heat recovery (MVHR) system designed for efficient air quality management in residential and multi-occupancy buildings. Features include high airflow, low energy consumption, integral humidity sensor, and various acoustic options.
	Vent-Axia Ventilation for New Build Residential Guide Comprehensive guide to ventilation solutions for new build residential properties from Vent-Axia, covering building regulations, product types, and installation best practices.
	Vent-Axia Lo-Carbon Sentinel Kinetic Advance MVHR System Detailed information on the Vent-Axia Lo-Carbon Sentinel Kinetic Advance, a next-generation heat recovery ventilation system offering high efficiency, low noise, and advanced control features for improved indoor air quality and comfort.
	Vent-Axia Lo-Carbon MVDC & Sentinel Multivent Range: Installation and Wiring Instructions Comprehensive installation and wiring guide for Vent-Axia's Lo-Carbon MVDC and Sentinel Multivent range of ventilation systems, covering setup, wiring, configuration, and troubleshooting.
	How to Clean the Vent-Axia MVHR Cell: A Step-by-Step Guide Learn how to effectively clean your Vent-Axia Mechanical Ventilation with Heat Recovery (MVHR) cell annually. This guide provides clear, step-by-step instructions and essential tips for maintaining your system.
	Vent-Axia Lo-Carbon Sentinel Multivent/Plus: Efficient MEV Ventilation Discover the Vent-Axia Lo-Carbon Sentinel Multivent/Plus, a high-efficiency mechanical extract ventilation (MEV) system designed for homes and commercial spaces. Features include low SFP, SAP PCDB recognition, and advanced control options for improved air quality and energy savings.
	Vent-Axia Product Selector Edition 19 Vent-Axia's comprehensive product selector guide, edition 19, detailing their range of ventilation and heating solutions for improved indoor air quality. Features include product specifications, technical advice, and information on energy efficiency standards.