Shark Steam & Scrub Steam Blaster Mop

Important Safety Instructions

SAVE THESE INSTRUCTIONS. READ ALL INSTRUCTIONS BEFORE USING THIS STEAM MOP.

This steam mop has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. It is not recommended to use an extension cord with this product.

General Warnings:

• DO NOT leave the steam mop unattended when plugged in. ALWAYS unplug the power cord from the electrical outlet when not in use and before servicing.
• DO NOT use with a damaged cord or plug. Return to SharkNinja Operating LLC for examination and repair if the unit is not working correctly, has been dropped, damaged, left outdoors, or dropped into water.
• DO NOT immerse the steam mop in water or any other liquids to protect against electric shock.
• DO NOT handle the plug or steam mop with wet hands or operate without wearing shoes.
• DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. DO NOT run steam mop over cord. Keep cord away from heated surfaces.
• DO NOT unplug by pulling on power cord; grasp the plug. DO NOT use extension cords or outlets with inadequate current-carrying capacity.
• Unplug before servicing.
• ALWAYS ensure the steam mop is UNPLUGGED when not in use.
• NEVER fill the water tank or attach the mop head when the steam mop is plugged in. Unplug and allow to cool before filling or changing heads.
• When cleaning the exterior, unplug and clean with a dry or damp cloth. DO NOT pour water or use alcohol, benzene, or paint thinner.
• DO NOT operate another appliance on the same circuit to avoid overload.
• ALWAYS unplug and allow the steam mop to cool before removing or changing mop heads or accessories to avoid scalding.

Use Warnings:

• NEVER turn the steam mop on its side or direct steam toward people, pets, or plants when in use.
• Use the system only for its intended use.
• DO NOT use for space-heating purposes.
• DO NOT use outdoors.
• DO NOT allow children to use the steam mop. Close attention is necessary when used near children, pets, or plants.
• Use only as described in this Owner's Guide.
• Use only manufacturer's recommended accessories.
• DO NOT put any objects into the steam nozzle openings; discontinue use if blocked.
• DO NOT put hands or feet under the steam mop as it gets very hot.
• Use ONLY on flat, horizontal surfaces. DO NOT use on walls, counters, or windows.
• DO NOT use on leather, wax-polished furniture, synthetic fabrics, velvet, or other delicate, steam-sensitive materials.
• DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water tank as this may damage the unit or make it unsafe. Use distilled water in hard-water areas.
• NEVER leave Dirt Grip® Soft Scrub pads in one spot for extended periods while using or storing, as this may damage surfaces.
• Dirt Grip® Soft Scrub pads can be released after unplugging and cooling.
• Exercise extreme caution when cleaning stairs.
• NEVER use the steam mop without the Dirt Grip® Soft Scrub pads attached.
• Keep your work area well lit.
• Store steam mop indoors in a cool, dry place.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• DO NOT carry the steam mop while in use.
• The steam emitted is very hot and may cause scalding; use caution.
• ALWAYS test an isolated area before cleaning. Check floor manufacturer's use and care instructions.
• DO NOT scrub any one area for an extended period.
• DO NOT use without Dirt Grip® Soft Scrub pads and water in the tank. Initial use may take longer than 20 seconds to start steaming.
• DO NOT use on unsealed wood or unglazed ceramic floors. Heat and steam may remove sheen from waxed or some unwaxed floors. Test an isolated area first.
• To prolong life, use distilled water. Add ONLY water to the tank. Chemicals or solutions may damage the mop and be unsafe.
• Liquid or steam must not be directed towards equipment containing electrical components. Dispose of contents/container with a licensed waste disposal site.
• DO NOT use to pick up flammable or combustible liquids or use in areas where they may be present.

What's Included

• A Steam Mop Handle
• B Steam Trigger
• C Quick-Release Cord Holder
• D Mop Pole
• E Water Tank
• F Mode Button
• G Mop Head
• H Steam Blaster
• I Dirt Grip® Soft Scrub Pads (Note: For additional pads, visit sharkaccessories.com)

Assembling Your Steam & Scrub

1. Insert the Mop Handle into the Steam Mop Body until it clicks into place. (See Figure 1: Mop handle inserted into mop body).
2. To attach the Dirt Grip Soft Scrub Pads, place both pads flat on the floor with plastic rings facing up. Align the unit directly over the plastic rings on the pads. Gently lower the Mop Head onto the pads, pressing until the pads are secure. (See Figure 2: Attaching pads to mop head).
3. Unplug the steam mop before filling the Water Tank. To remove the tank, pull it out from the mop body. Pull the top rubber fill cap back and fill the tank with cold or room temperature water ONLY. (See Figure 1 for tank removal, Figure 2 for filling).
4. When the tank is filled, reinstall it by inserting it back into the mop body.

Note: Adding chemicals or cleaning solutions (including vinegar) may damage the steam mop and could be unsafe for you, your family, and your pets.

Using Your Steam & Scrub

1. Twist the quick-release cord holder to unwrap the power cord completely. Plug into an electrical outlet.
2. Once plugged in, the mop is in Standby mode with both steam setting lights blinking. Press the Mode Button to select Light or Normal mode, then wait 20 seconds for steam to release.
3. Tilt the handle back to activate the spinning pads. To activate the Steam Blaster, press the spray trigger on the handle to blast away tough stains.

Note: Ensure both pads are properly installed before using.

Intelligent Steam Control®

The Shark Steam Mop offers 2 settings to select the ideal steam amount:

Steam Blaster®

1. To target tough messes, move the front of the nozzle 2 to 4 inches from the mess, then press and hold the Steam Blaster trigger as needed. Hold longer for tougher messes. (See Figure 3: Steam Blaster nozzle position).
2. Before scrubbing, wait 5 seconds for the steam blast to penetrate the mess. For more difficult messes, allow 20 seconds or more.

To Sanitize Floors*

1. Attach clean Dirt Grip® Soft Scrub Pads to the mop head.
2. Plug in the unit, tilt the mop handle down, and press the mode button to select NORMAL mode. Pads will start spinning.
3. Wait at least 20 seconds for steam production.
4. Start mopping with a forward and backward motion on an appropriate sealed hard floor surface. After three minutes, the unit is ready to sanitize.
5. Move the mop head slowly and evenly over the area to be sanitized, applying continuous downward pressure. Repeat slowly, covering the entire area with at least 15 strokes.

*Sanitization studies were conducted under controlled test conditions. Follow all directions carefully. Successful sanitization results have been demonstrated against specific bacteria species.

Troubleshooting

Caring for Your Steam Mop

After Use and Storage

1. Press the mode button until lights blink (Standby mode). Unplug the cord and place the mop upright. Allow it to cool completely. (See Figure 4: Mop in upright position).
2. Wait until pads have cooled completely, then carefully pull them off the discs, avoiding sharp edges. (See Figure 5: Removing pads).
3. After the unit has cooled and steam released, empty the water tank. Open lid, pour water into a sink or bathtub, then close lid.
4. To store, wait until cooled and steam released. Lock the mop in an upright standing position by raising the handle until the pole is straight. Store in a dry, protected area.

Dirt Grip® Soft Scrub Pads Care Instructions

• Care: Machine-wash pads separately with warm water and liquid detergent. Do not clean in a dishwasher, as detergents can cause streaks.
• NEVER USE BLEACH, POWDERED DETERGENT, OR FABRIC SOFTENERS: These will damage pads or reduce performance.
• Line-dry or tumble-dry on low setting to extend microfiber life.
• Loose fibers can be trimmed with scissors; do not pull them. (See Figure 6: Trimming fibers).

Replacement Pads

For best results, replace pads every 3-4 months with normal use. Dirt, grease, friction, and washing can break down fibers. You can purchase replacement pads and accessories at sharkclean.com.

Product Registration & Information

Register your purchase at registeryourshark.com.

Benefits of registering:

• Easier, faster product support and warranty access.
• Access to troubleshooting and product care instructions.
• Information on exclusive product promotions.

Record This Information:

• Model Number: S8200 Series / S8201
• Serial Number: [To be filled by user]
• Date of Purchase: [To be filled by user] (Keep receipt)
• Store of Purchase: [To be filled by user]

TIP: Model and serial numbers are on the QR code label on the bottom back of the steam pod.

Technical Specifications

• Voltage: 120V, 60 Hz
• Watts: 1120W
• Water Capacity: 350 ml (11.8 oz.)

This Owner's Guide is designed to help you get a complete understanding of your new Shark® steam mop.

SharkNinja Operating LLC

US: Needham, MA 02494

CAN: Ville St-Laurent, QC H4S 1A7

Customer Service: 1-800-798-7398

Website: sharkclean.com

Illustrations may differ from actual product. Specifications are subject to change without notice.

This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.

© 2024 SharkNinja Operating LLC.

DIRT GRIP, INTELLIGENT STEAM CONTROL, SHARK, and STEAM BLASTER are registered trademarks of SharkNinja Operating LLC.

Document reference: S8200Series_IB_12_MP_Mv13

Warranty Information

ONE (1) YEAR LIMITED WARRANTY

Applies to purchases from authorized retailers of SharkNinja Operating LLC. Coverage is for the original owner and original product only and is not transferable.

SharkNinja warrants the unit against defects in material and workmanship for one (1) year from the purchase date, when used under normal household conditions and maintained per the Owner's Guide, subject to conditions and exclusions.

What is covered:

• Original unit and/or non-wearable parts deemed defective will be repaired or replaced up to one (1) year from the original purchase date.
• Replacement units are covered for six (6) months following receipt or the remainder of the existing warranty, whichever is later.

What is NOT covered:

• Normal wear and tear of wearable parts (e.g., pads) requiring regular maintenance/replacement. Replacement parts are available at sharkaccessories.com.
• Units tampered with or used for commercial purposes.
• Damage from misuse, abuse, negligent handling, failure to perform maintenance, or mishandling in transit.
• Consequential and incidental damages.
• Defects caused by unauthorized repair persons.
• Products purchased, used, or operated outside North America.

How to Get Service:

Visit sharkclean.com/support for online self-help tools. Contact Customer Service at 1-800-798-7398 for product support and warranty service options. Register your product online at registeryourshark.com before calling.

SharkNinja covers shipping costs for sending the unit for repair/replacement. A fee of $25.95 (subject to change) applies when shipping the repaired/replacement unit.

How to Initiate a Warranty Claim:

Call 1-800-798-7398. Have your receipt (proof of purchase) and product ready. Registering online at registeryourshark.com is recommended. A Customer Service Specialist will provide return and packing instructions.

How State Law Applies: This warranty grants specific legal rights, which may vary by state. Some states do not permit exclusion/limitation of incidental/consequential damages.