SWIPE

Support

If you need help configuring the FIBARO Swipe, consult the guides and technical manuals available at: http://manuals.fibaro.com.

Package Contents

Installation

1. Step 1. Detach the frame

   Detach the front magnetic frame using the gap in the bottom of the housing.

   [Illustration shows a hand detaching the front magnetic frame from the main housing by pulling it away from the bottom edge where a small gap is indicated.]

2. Step 2. Slide out the plate

   Slide the detection plate down to remove it from the housing.

   [Illustration shows hands sliding the detection plate downwards out of the main housing.]

3. Step 3. Engage the batteries

   Pull out the paper stripe protecting the batteries.

   [Illustration shows the inside of the device with batteries, and a hand pulling a protective paper stripe from them.]

4. Step 4. Insert the plate

   Insert the detection plate back in the housing by sliding it up. The device will confirm powering up with an acoustic signal.

   [Illustration shows hands sliding the detection plate upwards into the housing. A sound wave symbol indicates an acoustic signal.]

5. Step 5. Replace the picture

   You can replace the existing photo with your favorite one at this point.

   [Illustration shows a hand inserting a new picture into the frame of the device.]

6. Step 6. Attach the frame

   Attach the front magnetic frame.

   [Illustration shows the front magnetic frame being attached back onto the device.]

7. Step 7. Place on the holder

   Place the assembled device on its holder.

   [Illustration shows the assembled FIBARO Swipe device placed on its holder.]

8. Step 8. Plug the USB cable

   Connect the power supply via the USB cable for the configuration process.

   [Illustration shows the USB cable connected to the device and a power source.]

Adding the device

The device must be in the direct range of the Z-Wave controller during the adding process.

1. Step 1

   Login to the Home Center controller and select "Devices" from the main menu.

   [Illustration shows a laptop screen displaying the FIBARO Home Center interface with "Devices" selected.]

2. Step 2

   Select the “Add or remove device” option from the left side menu.

   [Illustration shows the FIBARO Home Center interface with the "Add or remove device" option highlighted.]

   Click “Add” to start adding a new device (learning mode). Follow the instructions on the next page.

3. Step 3

   Move and hold your hand close to the center of the pad for around 4 seconds.

   [Illustration shows a hand held close to the center of the FIBARO Swipe pad.]

4. Step 4

   A loud sound sequence will confirm entering the menu; keep holding your hand.

   [Illustration shows a hand held to the Swipe pad, with a sound wave symbol indicating an acoustic signal.]

5. Step 5

   After hearing two short beeps, take your hand away and swipe up to confirm selection.

   [Illustration shows a hand swiping upwards on the Swipe pad after an acoustic signal.]

6. Step 6

   Wait for the device to be added to the system.

Gestures configuration

After the device is added, you can proceed with its configuration in the Home Center interface.

1. 1

   Click the [wrench icon ⚙️] in the top right corner of the FIBARO Swipe window.

   [Illustration shows a close-up of the FIBARO Swipe interface with a wrench icon highlighted.]

2. 2

   Select a gesture to which you want to assign a reaction and click the plus icon (New Reaction).

   [Illustration shows gesture selection and a "New Reaction" button.]

3. 3

   Select the device you want to control.

4. 4

   From the available options, select the reaction of the controlled device and complete the setup by clicking "Save".

   [Illustration shows the Home Center interface with device control options and a "Save" button.]

TIP: Configuration of sequences is described later in this manual.

Gesture sequences configuration

Sequence configuration is just as simple as gesture configuration.

1. 1

   Click the [wrench icon ⚙️] in the top right corner of the FIBARO Swipe window in the Home Center interface.

   [Illustration shows the FIBARO Swipe interface with a wrench icon highlighted.]

2. 2

   Drag and drop two or three gestures to create a desired sequence. Confirm the selection by clicking “Confirm new sequence”.

   [Illustration shows gestures being dragged and dropped to form a sequence.]

3. 3

   Wake up the Swipe according to the instructions on page 11 (section Menu).

4. 4

   Click the plus icon (New Reaction) next to the newly created sequence.

5. 5

   Select the device you want to control.

6. 6

   From the available options, select the reaction of the controlled device and complete the setup by clicking "Save".

   [Illustration shows the Home Center interface with sequence configuration options and a "Save" button.]

Gestures and sequences

FIBARO Swipe supports 6 gestures (up, down, left, right, clockwise, counter-clockwise) and combinations of gestures, called sequences. Sequences can be made of two or three gestures. Every sequence must be unique and cannot contain circular gestures. Additionally, two identical gestures may not be used next to each other. See examples below.

• Left

  [Illustration shows a hand moving from right to left.]

• Right

  [Illustration shows a hand moving from left to right.]

• Circular

  [Illustration shows a hand making a circular motion, indicated by a curved arrow.]

• Up

  [Illustration shows a hand moving upwards.]

• Down

  [Illustration shows a hand moving downwards.]

• Sequence

  [Illustration shows a hand performing a sequence of movements, indicated by multiple arrows.]

Acoustic signals

FIBARO Swipe is equipped with a buzzer, which signals detected gestures, menu position, and status of the device. Validity of every detected gesture or sequence is signalled by:

• 2 short beeps - gesture/sequence is valid
• 1 long beep - gesture/sequence is invalid
• Intermittent tone - during a circular gesture.

Powering modes

FIBARO Swipe can operate on either USB power supply or batteries.

Menu

Menu allows performing Z-Wave network actions. To enter and navigate the menu:

1. 1.

   Move and hold your hand close to the center of the pad.

2. 2.

   A loud sound sequence will confirm entering the menu; keep holding your hand.

3. 3.

   Wait for the buzzer to indicate the desired menu position:

   • 1 short beep - wake up the device
   • 2 short beeps - learning mode (add/remove)
   • 3 short beeps - reset the device

4. 4.

   Take your hand away and swipe up to confirm selection.

TIP: In battery mode, before entering the menu, a high-pitched beep will signal exiting the Standby Mode.