Philips 70PFL5656/F7 Quick Start Guide

Getting Started

Please read all instructions before following them step by step.

• A wide, open space is recommended for assembly.
• A Phillips-head screwdriver is required to fasten the stands to the TV set.
• Be careful not to injure your fingers and keep children away during assembly.
• It is recommended that two or more people remove the TV set from the box.

What's in the Box

The package typically includes:

• Quick start guide and Safety instruction/Limited warranty/Caution sheet
• TV unit
• Stands (2)
• Screws (M5 x 1.023" / 26 mm for stands)
• AAA Batteries (for remote, not explicitly shown but implied)

Unpacking the TV

1. Move the TV box to the front of the slipbox.
2. Carefully lay the TV set, with the screen side down, on the outer slipbox. This prevents deformation or damage to the unit.

Installing the Stands

Before attaching each stand:

• Peel off the protective film where each stand attaches to the TV to prevent it from getting stuck.
• Fasten each stand to the unit using two M5 x 1.023" (26 mm) screws.
• Ensure both stands are securely fastened.
• Carefully set up the unit upright.

Lifting the TV

It is recommended that two people lift the TV set.

Connection Overview

Connect your external devices using the appropriate cables:

• HDMI: Connect to HDMI input jacks on the TV (e.g., Blu-ray player, game console).
• Ethernet (LAN): For network connection.
• Optical (Digital Out): For audio output to a soundbar or receiver.
• Antenna/Cable In: Connect your antenna or cable service.

Note: Thin TVs can easily bend. To avoid damage, the TV MUST NOT be carried in a horizontal position when being moved.

Connecting Power and Antenna/Cable/Satellite

Connect your antenna or cable service to the 'ANTENNA/CABLE IN' port on the TV.

For detailed instructions on installing channels for antenna or cable using an RF cable, please refer to the online owner's manual at the provided support URL.

Connect your cable or satellite box to the TV via an HDMI cable to the 'HDMI input jack'.

Wall Mount Installation

Important Safety Information:

• This TV is compatible with third-party wall mount bracket kits. The recommended kit (sold separately) allows mounting the TV on the wall.
• For detailed wall mount installation instructions, refer to the wall mount instruction book.
• Funai Corporation is not responsible for any damage or injury resulting from self-installation of the TV wall mount bracket or mounting the TV onto the bracket.
• The wall mount bracket must be installed by experts.

Installation Precautions:

• Install the wall mount bracket on a sturdy vertical wall. Installation on a ceiling or slanted wall may cause the TV and bracket to fall, resulting in severe injury.
• Use only the specified screw length. Screws that are too long can cause internal damage, while screws that are too short can cause the TV to fall.
• Do not overtighten screws, as this may damage the product or cause it to fall.
• For safety, use two people to mount the TV onto a wall mounting bracket.
• Do not mount the TV while it is plugged in or turned on, to avoid electrical shock.

Required Spacing for Wall Mounting:

• Top: 11.8 inches (30 cm)
• Left and right sides: 5.9 inches (15 cm)
• Bottom: 3.9 inches (10 cm)

Screw Dimension for Wall Mount Bracket Kit:

• Model #: VLT6-B1 (for SANUS brand)
• Screw size: M6 x 1.378" (35 mm)

Regulatory Information

Federal Communications Commission (FCC) Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If interference occurs, users are encouraged to try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and the receiver.
• Connecting the equipment to an outlet on a circuit different from the receiver's.
• Consulting the dealer or an experienced radio/TV technician.

This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

Modifications: Changes or modifications not approved by Funai Corporation may cause harmful interference and void the user's authority to operate the apparatus.

Cables: Connections must be made with shielded cables with metallic RFI/EMI connector hoods to maintain FCC compliance.

Canadian Notice: CAN ICES-3 (B)/NMB-3 (B). Analog and digital television receiving apparatus, Canada BETS-7/NTMR-7.

Declaration of Conformity

Trade Name: PHILIPS

Model: 70PFL5656/F7

Responsible Party: Funai Corporation, Inc.

Address: 12489 Lakeland Road, Santa Fe Springs, CA 90670, USA

Telephone Number: 1 833 978 3323