IGLOO Portable Electronic Ice Maker User Manual

Introduction

This document provides instructions for the IGLOO Portable Electronic Ice Maker. It covers essential safety precautions, unpacking, product registration, operating procedures, cleaning and maintenance, and troubleshooting.

Models covered: ICE101-BLACK, ICE102C-WHITE, ICE102C-SILVER.

For questions, contact: 1-800-968-9853

Important Safeguards

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions carefully.
2. ⚠️ DANGER! To protect against risk of electric shock, do not immerse cord, plug or any parts of the unit in water or other liquids.
3. Close supervision is necessary when using this appliance near children. This appliance is not suitable for use by children.
4. Never leave an appliance unattended while in use.
5. Do not place an appliance on or near a hot gas or electric burner, or in a heated oven. Do not place on top of any other appliance.
6. Do not let the power cord of an appliance hang over the edge of a table or countertop or touch any hot surface.
7. Do not operate any electrical appliance with a damaged cord or plug or after the appliance malfunctions or has been dropped or damaged in any manner. If damage is suspected, contact the nearest authorized service center for examination, repair or electrical or mechanical adjustment.
8. Unplug from power outlet when not in use, before putting on or taking off attachments, and before cleaning.
9. The use of accessory attachments that are not recommended by the appliance manufacturer may cause fire, electric shock or injury.
10. Avoid contact with moving parts when the unit is in operation.
11. Never touch the cooling elements when the unit is in operation.
12. Do not use outdoors.
13. Do not use appliance for other than its intended use.

SAVE THESE INSTRUCTIONS

Household Use Only

Unpacking Your Ice Maker

1. Inspect and remove all packing materials, including foam and adhesive tape, from both the inside and outside of the unit.
2. Inspect and remove any remaining packing, tape, or printed materials before powering on your IGLOO appliance.

⚠️ WARNING: Please read this manual carefully before using. Retain it for your future reference.

Product Registration

Keep for your records to obtain Warranty Service.

Thank you for purchasing this quality IGLOO product. This easy-to-use manual will guide you in getting the best use out of your appliance.

Remember to record the model and serial number. They are on a label in the back of the appliance.

Staple your receipt to your manual. You will need it to obtain warranty service.

Safety Instructions: Electrical Requirements

Wiring and Grounding Instructions

This appliance must be plugged into at least a 15 AMP 110-115 VOLT 60 Hz GROUNDED OUTLET. This appliance must be grounded. It is equipped with a 3-wire cord having a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

⚠️ WARNING! Improper use of grounded wire can result in the risk of electric shock. Consult a physician if necessary. Do not attempt to defeat this safety feature by modifying the plug.

Avoid the use of an extension cord because it may overheat and cause a risk of fire. However, if it is necessary to use an extension cord:

• A. Use only 3-wire extension cords with 3-blade grounding plug.
• B. The marked rating of an extension cord must be equal to or greater than the rating of this appliance.
• C. It should be positioned such that it does not drape over the counter or tabletop where it can be pulled on by children intentionally.

Attempting any maintenance or cleaning:

To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

NOTE: Pressing the Power ON/OFF button to an off position does NOT disconnect the appliance from the power supply.

Specifications

Parts, Functions and Features

The IGLOO Portable Electronic Ice Maker consists of the following parts:

• 1. Cover with transparent window
• 2. Ice maker and pusher
• 3. Water reservoir (Not shown)
• 4. Control panel
• 5. Water drain cap: For draining water from ice water (Located on the Front Button of Unit)
• 6. Compressor cooling fan (Do not block air flow)
• 7. Ice shovel
• 8. Ice basket

Control Panel

The control panel is designed for easy use, featuring buttons and LED indicators:

• A. Power ON LED indicator light
• B. Power ON/OFF button
• C. Ice cube SELECT SIZE button
• D. Selected ice size LED light indicator: Displays SMALL or LARGE ice cubes to make.
• E. "ADD WATER" indicator: Alerts that there is no water in the water reservoir; water must be added.
• F. "ICE FULL" LED indicator

[Diagram of control panel with labels A-F and buttons ON/OFF, SELECT, S, L]

Operating Instructions

This portable icemaker uses a fully automatic control system with an advanced microcomputer for easy and convenient ice making. Making ice is simple and fast. Just add water, plug into an outlet, and press the ON button. You can select one of the two ice cube sizes with the touch of a button. When first turning on the unit or during icemaking cycles, the compressor will stay idle for 3 minutes while energizing.

Warning indicators alert you to fill water when the reservoir is empty and to remove ice when the storage basket is full. The icemaker also has built-in safeguards that can limit accidental damage by automatically shutting down the system when necessary.

Pre-Operating Instructions

Please read carefully.

1. During transportation or use, the incline angle of the icemaker cabinet should not exceed 45 degrees. Do not turn the icemaker upside down, as this could cause the compressor or refrigerating system to operate incorrectly. When the icemaker is moved or transported, allow time for the fluids in the compressor to settle. Before using the icemaker for the first time, please wait 2 hours after the unit has been leveled and positioned in its proper place.
2. Please ensure the icemaker is level and on a stable table or platform to avoid malfunction.
3. The machine must be placed on a dry and level surface with sufficient ventilation, far from heat sources such as ovens, heaters, and corrosive gases. Leave an 8-inch clearance on all sides of the icemaker for proper ventilation.
4. Do not fill the water reservoir with hot water, as this may damage the icemaker. It is best to fill the water reservoir with water of room temperature or lower.

Operating Instructions

1. Open the top cover, take out the ice storage basket, and fill the water reservoir with drinkable water (tap, purified, or bottled) up to the level mark. Replace the ice storage basket.
2. [Illustration showing lifting the ice basket to add water]
3. Make sure that the water level does not reach above the level mark or the bottom of the ice storage basket. Close the top cover.
4. Note: During the operation process, if the water level in the reservoir becomes too low, the machine will automatically stop operating, and the "Add Water" indicator will display on the LED.
5. Plug the unit into a grounded outlet. Push the ON/OFF button on the control panel to turn on the machine.
6. Select the desired size of ice cube by pressing the S or L ice selector button:
   • S = Small ice cubes (Approx. 7 minutes)
   • L = Large ice cubes (Approx. 12 minutes)
7. The icemaker will start making ice soon after. The next cycle of 9 ice cubes is complete (based on water temperature, ambient room temperature, and selected ice cube size).
8. Note: To stop the operation, press the ON/OFF button.

Operating Process

1. Water is pumped from the water storage tank to the water box, which may take up to 1 minute.
2. The icemaking cycle begins when the evaporator rods are dipped into the water box. You will hear the compressor working.
3. It will take approximately 5-13 minutes for each icemaking cycle, depending on the size selected. Larger sizes require more time. After the cycle is finished, the water box will tilt forward, and the remaining water will flow back into the water storage tank. The evaporator rods will then release the ice cubes.
4. Note: If the room ambient temperature is below 60°F, it is suggested to use small ice cube sizes to prevent ice cubes from fusing together.
5. Approximately 60 seconds later, the water box will tilt backwards, and the ice pusher will push the ice into the ice storage basket. After the water box returns to its original position, the next icemaking cycle will begin.
6. When the maximum capacity of ice cubes is collected and the ice reaches the temperature sensor, the icemaker will automatically stop operating, and the "ICE FULL" LED indicator will light up. If more ice is needed, remove the ice from the ice storage basket, then replace the basket into the machine, ensuring it is placed back in its original position. Note: When replacing the basket, ensure that the temperature sensor is above the basket for proper operation.
7. To continue making ice, check that there is water in the water storage tank. If there is no water, no water will be pumped into the water box, and the operation will stop. The "Add Water" LED display will light up. Press the "OFF" button. Fill the water storage tank with water, and then press the "ON" button for the icemaker to begin operating again. Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting.
8. If the compressor stops for any reason such as water shortage, too much ice, or power off, do not restart the machine right away. Wait at least 3 minutes before restarting the machine.

Cleaning and Maintenance

Before using your icemaker, it is strongly recommended that you clean it thoroughly. Be sure to clean the icemaker regularly.

1. When cleaning, ensure the power is turned off and the plug is disconnected from the outlet. When plugging or unplugging the unit, pull directly on the plug, never on the power cord.
2. Remove the ice storage basket.
3. Drain any remaining water from the unit. Remove the drain cap, then the rubber plug from the spout. When reassembling, the rubber plug must be inserted first into the spout, followed by the cap. Otherwise, the icemaker will leak.
4. Use a mild detergent diluted in warm water and wipe with a soft towel or sponge. ⚠️ Solvents, detergents, and abrasives must never be used for cleaning.
5. Wipe the inner parts, such as the ice storage basket, water reservoir, water box, ice pusher, and evaporator rods.
6. The outside of the icemaker should be cleaned regularly with a mild detergent solution, warm water, and a soft cloth.
7. Dry the interior and exterior with a soft cloth.
8. To begin making ice once the unit has been cleaned, pour clean water into the water reservoir and fill up to the level line, following operating instructions. ⚠️ Never tilt or place the icemaker on its side; otherwise, you must wait 10 hours for the compressor coolant to settle.
9. To ensure the cleanliness of the ice cubes, the water in the water storage tank should be replaced every 24 hours.
10. When the machine is not in use or will not be used for an extended period, unscrew the drain cap, then remove the rubber plug behind the unit to empty the remaining water in the water reservoir completely. (Follow instructions in number 4 above.)

[Description of drain cap, drain spout, and rubber plug components]

Troubleshooting Guide

ℹ️ Note: There is protective circuitry inside this icemaker to protect the circuitry from overheating, and the icemaker will automatically shut down to prevent damage if activated. Please disconnect the power cord and restart after 30 minutes of cooling down time.