CantoUSA cWORK & cRUN Series Installation Manual

Introduction

This manual provides standard installation instructions for the CantoUSA cWORK Worklight Series and cRUN Running Light Series. It is intended for qualified, trained systems integrators or electrical contractors. Please read all warnings, notices, and instructions before installing or using this product.

CantoUSA accepts no liability for damages resulting from failure to follow the installation, operating, maintenance, and safety procedures described in this manual.

All relevant safety and health standards of the appropriate local city and state electrical/safety directives must be complied with.

Product Safety Notices

⚠️ WARNING! Basic safety precautions should always be followed when using electrical equipment:

• Read and follow all safety instructions.
• Do not use outdoors unless the product is specified for outdoor environments.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Do not use this equipment for other than its intended use.
• For warranty and service issues, refer to your certified local CantoUSA dealer.

General Warnings

⚠️ WARNING! You must have access to a main circuit breaker or other power disconnect device before installing any wiring. Ensure power is disconnected before installation to avoid dangerous voltages and device damage. A qualified electrician must perform this installation.

⚠️ WARNING! Refer to the National Electrical Code® and local codes for cable specifications. Failure to use proper cable can result in equipment damage or danger to personnel.

⚠️ WARNING! This equipment is intended for installation in accordance with the National Electric Code® and local regulations, and for indoor applications only. Disconnect power at the breaker box before performing any electrical work.

⚠️ WARNING! This Lighting Fixture is NOT for residential installation or use.

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

Power Requirements

⚠️ WARNING! The cWORK/cRUN should be connected to a constant circuit (on / off) or dimmer rack.

The cWORK/cRUN operates on 120VAC, single phase only and draws a maximum of 92 Watts. It offers ON or OFF operation or can be connected to a dimmer or a dimmer-controlled circuit.

What's Included in the Box

The cWORK/cRUN is supplied with a 1-meter TRUE1 Connector. This cable can be connected to any single-phase 120 VAC power source.

The cWORK/cRUN TRUE1 input/output connection is at the rear of the unit. A maximum of 12 cWORK/cRUN units can be daisy-chained using 12 AWG wire.

IMPORTANT! The cWORK/cRUN must be connected to and properly grounded to a viable earth ground.

Connecting

Connecting Procedure:

1. When connecting, match the notch on the cable connector to the corresponding guide slot on the chassis.
2. After inserting properly as shown, twist the cable connector clockwise to lock.
3. The proper twist-lock is achieved when the silvery tab is in the indicated position and an audible click is heard.

SAFETY WARNING: Incorrect insertion may cause electrical contact misalignment, resulting in equipment malfunction and/or personal injury.

Disconnecting Procedure:

1. Press the locking mechanism.
2. Pull the connector apart.

Mounting

The cWORK/cRUN is simple to install and position where work lighting is needed. The unit should be installed with a C-Clamp and Safety Cable (supplied by others). When mounting, follow all national and local codes for safe installation and use.

Unit weight, without accessories, is 4.7 lbs. (2.13 kg).

Figure 1: cWORK/cRUN Light Features - This figure illustrates the dimensions and mounting points of the cWORK/cRUN unit, including optional eyebolt mount location and mounting holes.

NOTE: A safety cable (supplied by others) should be used and may be required by codes when hanging this luminaire.

Adjusting Tilt

The tilt of the cWORK/cRUN can be adjusted using the two lock knobs on each side of the luminaire. Loosen, but DO NOT REMOVE, each knob to allow the unit to swing up and down. Set the desired tilt angle and re-tighten the two locking knobs to secure the position.

Changing the Reflector

Step 1: Place the cWORK/cRUN on a flat surface. Using a Phillips screwdriver, remove the 4 screws circled in red (Reference Figure 1). Keep these screws for reinstallation.

Step 2: Remove the side panel and set it aside. Remove the outer lens and set it aside (Reference Figure 1).

Step 3: If supplied with a diffuser, remove it by popping it off the reflector. Remove the reflector by twisting it counterclockwise -1/8 of an inch (Reference Figure 1).

Step 4: Install the new reflector by lining up the 3-tab slots on the reflector to the 3 tabs on the COB holder. Turn 1/8 of an inch clockwise to lock the reflector into place. Snap the diffuser, if supplied, onto the new reflector by lining up the 4 tabs and snapping it into place (Reference Figure 2).

Step 5: Reinstall the outer lens by sliding it back into the access port. Reinstall the side panel (Reference Figure 2).

Step 6: Reinstall the 4 screws provided (Reference Figure 2).

Figure 1 & 2: Disassembly and Reassembly - These figures illustrate the steps for removing and installing the reflector, lens, and side panel.

Cleaning and Care Instructions

⚠️ WARNING! All cleaning should be performed with power completely shut off at the break box or unplugged from the AC outlet. Never remove protective covers from the luminaire when powered. Wear appropriate protective eyewear and gloves when cleaning the fixture.

The cWORK/cRUN requires only simple routine maintenance.

⚠️ WARNING! Do not use ammonia-based cleaners, acetone, or other harsh solvents on or near the LED source, as these can damage the fixture.

For any questions regarding use or care, contact CantoUSA technical support or your local Authorized Dealer.

Service and Maintenance

For all other service and maintenance issues, please contact CantoUSA or an authorized CantoUSA dealer.

⚠️ WARNING! Disassembly (other than as described herein), alterations, or unauthorized service will void the product warranty. Contact CantoUSA or your local Authorized dealer for technical support and service.

Troubleshooting

If the cWORK/cRUN does not function, check power, all connections, and review the installation instructions to ensure correct installation. If the unit still does not function, contact CantoUSA at 888-252-5912 or the local dealer who supplied the product.

Accessories

CantoUSA offers accessories for use with the cWORK/cRUN. Please call your dealer or CantoUSA sales team at 888-252-5912 to order.

Spare Parts

All components are available as spare parts. CantoUSA recommends using original components for spare parts. Contact CantoUSA technical team at 888-252-5912 to order or replace parts.

Warranty

CantoUSA's warranty covers all structural and manufacturer defects for three years from the date of purchase, and 10 years on the LED array. For any issues, contact CantoUSA at 888-252-5912 or the local dealer who supplied the product. Please report the product's serial number when making a warranty claim.