Allmatic TECH3 POWER and B.RO Series Remote Transmitters

Product Overview

This document provides information on the Allmatic TECH3 POWER and B.RO series remote transmitters. These transmitters are designed for controlling automatic door openers, gate openers, and similar devices. Any other use is considered improper and prohibited.

Product Identification and Functions

The B.RO series transmitters (B.RO1/2/4WN) feature the following:

• A. Transmitter LED: Illuminates during code transmission.
• B. Power Battery: The power source for the transmitter.
• 1. Key 1
• 2. Key 2
• 3. Key 3
• 4. Key 4
• 5. Hidden Key: Used for remote learning and cancellation.

Opening the B.RO WN Transmitter: Use a screwdriver to gently press and lever at the indicated point (Figure F.2). To close, ensure the metal pieces are in contact with the battery, secure the rear part, and lower it, making sure the metal pieces are positioned inwards.

The TECH3 POWER transmitter also has similar functions, with a hidden key for learning and cancellation.

Technical Specifications

B.RO BEST Series (B.RO1WN/B.RO2WN/B.RO4WN)

• Power Supply: 1 x 12V 23A alkaline battery
• Consumption: 22mA during transmission
• Number of Keys: B.RO1WN - 1, B.RO2WN - 2, B.RO4WN - 4
• Antenna: Incorporated
• Radiated Power (ERP): <1mW
• Oscillator Type: SAW
• Frequency: 433.92MHz ±100KHz
• Range: 50-150m
• Operating Temperature: -10°C to +55°C

TECH3 POWER

• Power Supply: 1 x 3V CR2032 lithium battery
• Consumption: 12mA during transmission
• Number of Keys: 3
• Antenna: Incorporated
• Radiated Power (ERP): <1mW
• Oscillator Type: SAW
• Frequency: 433.92MHz ±100KHz
• Range: 10-80m
• Operating Temperature: -10°C to +55°C

Transmitter Memorization

The learning mode depends on the specific receiver or control unit. Refer to the respective instructions for your receiver or control unit. Activate the receiver's learning procedure, then press the desired key on the transmitter.

Remote Transmitter Memorization

This procedure allows learning a new transmitter without direct access to the receiver, provided you have an already memorized transmitter for the same receiver.

1. Ensure you are within the radio range of the receiver or control unit.
2. Using a pointed object (e.g., a paper clip), press the hidden key of the already memorized transmitter for 1 second.
3. Press the key on the new transmitter you wish to memorize for approximately 2 seconds.

Caution: Do not perform this procedure if multiple receivers are within the same radio range.

Transmitter Cancellation

This procedure removes a transmitter from the receiver (all keys).

1. Ensure you are within the radio range of the receiver or control unit.
2. Using a pointed object (e.g., a paper clip), press and hold the hidden key of the transmitter to be deleted.
3. While keeping the hidden key pressed, press Key 1 for 2 seconds.

Caution: Do not perform this procedure if multiple receivers or control units are within the same radio range.

Low Battery Indication (B.ROWN Series Only)

• Solid LED during transmission: Battery OK
• Flashing LED during transmission: Low battery

A low battery significantly reduces the transmitter's range. Replace the depleted battery with a new one of the same type to restore normal operation.

Product Disposal

This product is an integral part of the automation system it controls and must be disposed of accordingly. Disposal operations, like installation, should be performed by qualified personnel. Please consult local regulations for proper recycling and disposal methods for this product category. Do not dispose of this product in household waste, as indicated by the symbol ?.

Declaration of Conformity

The manufacturer, Allmatic S.r.l., declares that the products described in this manual comply with Community Directives: 2014/53/UE, 2014/35/UE, 2014/30/UE, and relevant standards including EN 62368-1, EN 301489-1, EN 301489-3, EN 300220, EN 62479. A complete declaration is available on the website www.allmatic.com.

Certifications: CE, UK CA