Whirlpool Undermount Rangehoods User Manual

Warning & Safety Information

Technical Guidance

• There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.
• There is a fire risk if cleaning is not carried out in accordance with the instructions.
• Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from appliances burning gas or other fuels.
• The minimum distance between the hob surface and the lowest part of the rangehood is 600mm. This distance shall be at least 650mm, if the rangehood is installed over a gas hob. If the instructions for the gas hob specify a greater distance, this has to be taken into account.
• Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air is fulfilled.
• If the supply cord of this equipment is damaged, it must only be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance has been designed for indoor domestic use only.
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Do's & Don'ts

• Do not flambe under the rangehood.
• Do not remove or inspect the filters whilst the hood is in operation.
• You must read the details concerning the method and frequency of cleaning.

Safety With Children

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Young children should be supervised to ensure that they do not play with the appliance.

Operating Instructions

Models: 520, 750 & 900 Undermount Rangehoods

Fan Speed

LOW/OFF/HIGH switch - Located on the left-hand side of the control panel. This unit features 3 speed settings: single line indicates low speed, double lines indicate medium speed, and triple lines indicate high speed. To turn the unit off, set the speed switch to the 0 position (off).

Light

On/Off switch - Located on the left-hand side of the control panel.

Maintenance & Troubleshooting

General Maintenance

Ensure that the power to the unit is switched off prior to cleaning. The surface should only be cleaned with warm soapy water and a soft non-abrasive cloth. In coastal environments and humid areas, more frequent cleaning is required to maintain the finish.

Filter

This unit is supplied with an Aluminium filter designed for ducted installations. The Aluminium filter is dishwasher safe or can be cleaned with hot soapy water. Ensure the filter is thoroughly dry before re-installing.

For recirculating mode, Carbon filters can be ordered to eliminate odours. This type of filter cannot be cleaned and should be replaced every 3-6 months depending on use.

Lamps

Before replacing, ensure that the lamps are completely cool and the power to the unit has been switched off. Replacement lamps can be purchased from customer care. To remove the lamp, twist it in an anti-clockwise direction. Be careful when installing the new lamp not to make contact with the skin, as this may damage the lamp and shorten its life.

Lamp Type: GU10 - 3W LED (x2)

Installation & Ducting

IMPORTANT: Before handling the rangehood during installation, it is recommended that you remove the filter to prevent damage.

NOTICE: If the instructions for the gas hob specify a greater distance, this has to be observed. Any installation above 750mm will compromise performance.

NOTICE: ALL DUCTING MATERIAL MUST BE COMPLIANT WITH THE LOCAL LAWS IN FORCE.

Installation Steps

1. Remove the filter and light globes. (If installed)
2. Remove the stainless steel fascia (2 screws) - take care not to damage the fascia.
3. Determine the most efficient path for the ductwork, minimise bends and keep the length of the ductwork to a minimum.
4. It is important to run and finish (install roof / wall caps) prior to installation on the hood.
5. Cut out the cabinetry as per the installation diagram. Ensure that access has been allowed for the power cable.
6. Hold the hood up to the underside of the cabinet (2 people required); Screw the hood to the cabinetry.
7. Attach the ducting adaptor to the ducting.
8. Re-install the stainless steel fascia.
9. Re-install filter.
10. Plug in the power to the unit, turn on and test.

WARNING: Do not penetrate any screws into the rangehood as this may result in electrical hazards. Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Version Information

Version 1.2. We are committed to ongoing research and development. Every effort has been made to ensure all information in the user manual is correct at the time of going to print. Dimensions should be used as a reference only and actual dimensions should be taken from the physical product.