User Manual: Undermount Rangehoods

Important Information

IMPORTANT: Please ensure that you read through this user manual prior to installation and use. This manual contains important information to ensure optimal performance and keep you safe. Please retain your proof of purchase, as this will be required in the event that you require warranty service. Remember to retain this manual for future reference.

Contents

• Warning & Safety Information
• Operating Instructions
• Maintenance & Troubleshooting
• Installation & Ducting
• Contact Details

Warning & Safety Information

Technical Guidance

• Ensure adequate ventilation when using the rangehood simultaneously with appliances burning gas or other fuels.
• There is a fire risk if cleaning is not performed according to instructions.
• Exhaust air must not be discharged into existing flues used for appliances burning gas or other fuels.
• Minimum distance between hob surface and the lowest part of the rangehood: 600mm for electric hobs, 650mm for gas hobs. If gas hob instructions specify a greater distance, adhere to that.
• Ensure compliance with applicable regulations regarding exhaust air discharge.
• If the supply cord is damaged, it must be replaced by the manufacturer, service agent, or a qualified person to avoid hazards.
• This appliance is designed for indoor domestic use only.
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Do's & Don'ts

• Do not flambe under the rangehood.
• Do not remove or inspect filters while the hood is operating.
• Read the details concerning the method and frequency of cleaning.

Safety With Children

• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience/knowledge, unless supervised or instructed by a person responsible for their safety.
• Young children should be supervised to ensure they do not play with the appliance.

Operating Instructions

520, 750 & 900 Undermount Rangehoods

Control Panel:

The control panel features controls for Fan Speed and Light.

Fan Speed:

A LOW/OFF/HIGH switch is located on the left side of the control panel. The unit features 3 speed settings: a single line indicates low speed, double lines indicate medium speed, and triple lines indicate high speed. To turn the unit off, set the speed switch to the 0 position.

Light:

An On/Off switch for the light is located on the left-hand side of the control panel.

Maintenance & Troubleshooting

General Maintenance

Ensure the unit's power is switched off before cleaning. Clean the surface with warm soapy water and a soft, non-abrasive cloth. In coastal or humid environments, more frequent cleaning is needed to maintain the finish.

Filter

This unit is supplied with an Aluminium filter for ducted installations. The Aluminium filter is dishwasher safe or can be cleaned with hot soapy water. Ensure the filter is thoroughly dry before re-installing.

For recirculating mode, Carbon filters can be purchased separately to eliminate odours. These filters cannot be cleaned and should be replaced every 3-6 months depending on use.

Lamps

Before replacing lamps, ensure they are completely cool and the unit's power is switched off. Replacement lamps can be purchased from customer care. To remove a lamp, twist it in an anti-clockwise direction. Be careful when installing a new lamp to avoid contact with skin, as this may damage the lamp and shorten its life.

Lamp Type: GU10 - 3W LED (x2)

Installation & Ducting

Diagram Description: The rangehood is shown with dimensions in mm. Key dimensions include the width (e.g., 520/750), depth, and duct outlet diameter (Φ150). It is noted as "10A plug fitted".

IMPORTANT: Before handling the rangehood during installation, it is recommended to remove the filter to prevent damage.

Minimum Height Requirements:

The diagram illustrates the minimum height from the hob surface to the underside of the rangehood:

• Electric hob: 600mm
• Gas hob: 650mm

NOTICE: If the instructions for the gas hob specify a greater distance, this must be observed. Any installation above 750mm will compromise performance.

Ducting Options:

Diagrams show three ducting configurations: TOP DUCTING, SIDE DUCTING, and RE-CIRCULATING (requires Carbon filter).

NOTICE: All ducting material must be compliant with local laws.

Installation Steps:

1. Remove the filter and light globes (if installed).
2. Remove the stainless steel fascia (2 screws) carefully to avoid damage.
3. Determine the most efficient path for the ductwork, minimizing bends and keeping the length to a minimum.
4. Install roof or wall caps before installing the hood.
5. Cut out the cabinetry as per the installation diagram, ensuring access for the power cable.
6. With assistance (2 people required), hold the hood up to the underside of the cabinet and screw it securely.
7. Attach the ducting adaptor to the ducting.
8. Re-install the stainless steel fascia.
9. Re-install the filter.
10. Plug in the power to the unit, turn it on, and test.

WARNING: Do not penetrate screws into the rangehood casing, as this may result in electrical hazards. Failure to install screws or fixing devices according to these instructions may result in electrical hazards.

Version Information

Version 1.2

We are committed to ongoing research and development. Every effort has been made to ensure all information in the user manual is correct at the time of printing. Dimensions should be used as a reference only, and actual dimensions should be taken from the physical product.