GTPLAYER GT829 Gaming Chair Assembly Instructions

Parts and Accessories

Please check and ensure all parts are present in the package. Contact GTPLAYER if any part is missing.

• a Back (x1)
• b Seat (x1)
• c Base (x1 set)
• d Armrest (x1 set)
• e Gas Lift (x1)
• f Mechanism (x1)
• g Footrest (x1 set)
• h Connector (x1)
• i Caster (x5)
• j Headrest (x1)
• k Lumbar Pillow (x1)
• m Footrest Rail (x2)
• n Gas Lift Cover (x1)
• L Wrench (x1)

Screws and Other Accessories:

• O M6*22 (4pcs)
• P M8*20 (4pcs)
• Q M8*40 (4pcs)
• S M5*8 (1pc)
• T M6*20 (5pcs)
• U φ16*φ24 (4pcs)
• W M6*35 (4pcs)
• X M8*30 (4pcs)
• V CAP (4pcs)
• Z M6*25 (2pcs)

Assembly Instructions

1. Install the base.

   Align the screw holes horizontally. Use 5 x M6*20 screws (T) to secure the mechanism (f) to the seat (b).

   Attention: Snap on the ground to align the screw holes.

2. Insert the casters.

   Insert 5 casters (i) into the base (c).

3. Install the gas lift and insert the gas lift cover.

   Place the gas lift (e) into the base (c). Place the gas lift cover (n) over the gas lift.

4. Install the mechanism.

   Attach the mechanism (f) to the underside of the seat (b) using 4 x M6*22 screws (O). Ensure the front of the mechanism is aligned with the front of the seat.

   Attention: DO NOT tighten the screws completely until they are all fixed in the correct position.

5. Install the footrest rails.

   Align the screw holes horizontally. Use 4 x M6*35 screws (W) to attach the footrest rails (m) to the seat (b). Tighten first, then loosen by half a turn to smoothly install the footrest.

6. Install the footrest.

   Attach the footrest (g) to the footrest rails (m) using 2 x M6*25 screws (Z) and 1 x M5*8 screw (S). Ensure correct orientation of the footrest.

   Attention: Please refer to the diagram for the front and back sides and proceed with caution during installation.

   Note: DO NOT mistake the front and back of the footrest paddle. Install the footrest as shown. Only install one side of the footrest rail.

7. Place the seat on the gas lift.

   Carefully align the mechanism on the seat with the gas lift and lower the seat onto it.

8. Install the connector on the chair back.

   Attach the connector (h) to the chair back (a) using 4 x M8*30 screws (X). Note the direction of the connector.

9. Install the connector into the rear end of the mechanism.

   Connect the chair back assembly to the seat mechanism using 4 x M8*20 screws (P). Secure the Velcro on the backrest to the seat bottom.

   Note: Connector (h) INTO mechanism (f).

10. Align the screw holes and install the armrests.

    Attach the armrests (d) to the seat (b) using 4 x M8*40 screws (Q) and 4 x φ16*φ24 washers (U). Put washer (U) between the armrest and chair body.

    Attention: DO NOT tighten the screws completely until they are all fixed in the correct position.

11. Install the headrest.

    Attach the headrest (j) to the top of the chair back (a). The belt can be adjusted up or down.

12. Put on the lumbar pillow. Complete.

    Place the lumbar pillow (k) on the chair back for support.

Functions Display

A. Height Adjustment

Lift up the "LIFT" lever to adjust the height of the chair. Release the lever at the desired height. Lift your body slightly off the seat when adjusting the height.

B. Back Recline Function

Lift up the "RCL" lever, and the back angle tilts independently with user's motion. Push down on the "RCL" lever, and the back angle is locked in position. Rest on the back when resetting it to its normal position, otherwise the back may rebound rapidly.

Frequently Asked Questions

Q1: Isn't the footrest sliding smoothly?

A1: Adjust the footrest rails. Follow Method 1: Align the screw holes horizontally. Tighten first, then loosen by half a turn to smoothly install the footrest. If Method 1 didn't work, try Method 2: Apply a small amount of lubricating oil (not included) evenly on the footrest rods to make the footrest slide more smoothly.

Q2: Why do the armrests loosen after a period of use?

A2: In most cases, the screws of the armrests and back become loose after a period of use. Re-tightening the screws can fix the problem.

Safety & Maintenance

Safety Precautions:

• Sit in the center of the chair with your back to the backrest. ✔️
• DO NOT sit at the front edge of the chair. ❌
• DO NOT stand on the chair. ❌
• DO NOT use the chair with more than one person. ❌
• DO NOT turn the chair around when a person is sitting in it. ❌
• DO NOT push down on the backrest when a person is reclined. ❌
• DO NOT place only your back on the chair. ❌

Safety Information:

• Use this chair for seating only one person at a time.
• DO NOT stand on the chair.
• DO NOT use the chair as a stepladder.
• DO NOT use the chair unless all screws are firmly secured.
• Avoid contact with sharp objects to prevent puncturing the fabric.
• Every 6 months, check all screws to ensure they are all tight.
• To clean, spot clean only with a damp towel and mild cleaner. First test on a small obscure area of fabric.

Maintenance

GTPLAYER is dedicated to providing high-quality and safe products for comfort. We guarantee each new product to be free from defects in materials and/or workmanship. This warranty does not apply to normal wear and tear, damage caused by neglect, lack of maintenance, abnormal operation, unreasonable use, or damage caused by accessories or parts not manufactured by GTPLAYER, or components altered and/or disassembled.

This warranty does not cover products purchased from unauthorized retailers or not owned by the original consumer. It also does not cover lost or stolen items/parts.

Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is hereby disclaimed.

GTPLAYER shall not be liable for any incidental, consequential, special, or punitive damages of any kind for breach of the express limited warranty on this product, or any warranty implied by operation of law. Other than the express limited warranty set forth above, there are no other warranties that accompany this product, and any oral, written, or any other express warranties are disclaimed.

Customer Support

Dear Customer, Thank you for choosing GTPLAYER. We are implementing our brand and design concept “BE COOL BE FREE” to enrich the gaming and shopping experience for customers.

For safe use, please read this manual before installation and keep it for after use. Please feel free to email us at us@gtplayer.com if you have any concerns about our products. We will reply within 24 hours.

Important Notes:

• When the product is damaged due to courier problems, please contact our customer service for verification.
• We will rectify the issue as soon as possible.
• We provide a 1-year quality assurance.

We offer product explanations, installation instructions, product maintenance, and maintenance methods.

If you are satisfied with our product and service:

• Please add our store to your favorites.
• Please recommend our products to your friends.
• Please leave us your purchase experience on our store or product page.

Feedback or reviews from you will greatly help us offer better services to players around the world.

Best regards!

*All information stated is correct at the time of print and is subject to change without notice.