GTPLAYER Assembly Instructions

01 Details of accessories

Please check and ensure all accessories are in the package. Contact customer service if anything is missing.

Accessories List:

• a BACK x1
• b SEAT x1
• c BASE x1
• d ARMREST x2
• e GAS LIFT x1
• f MECHANISM x1
• g FOOTREST x1
• h CONNECTOR x1
• i CASTER x5
• j HEADREST x1
• k LUMBAR PILLOW x1
• l WRENCH x1
• m FOOTREST RAIL x2

Screws and Parts:

• CAP x4
• Rubber Ring x2
• M6*22 x4pcs
• M8*18*1.5mm x12pcs
• M8*20 x4pcs
• M6*20 x10pcs
• M6*30 x4pcs
• M8*40 x4pcs
• φ16*24*1.5mm x4pcs
• M6*30 x4pcs

02 Chair Installation

Please keep the original box in case you might need to return or replace the product.

1. Step 1: Combine C1 and C2 with 10pcs of M6*20 screws. Note: Remove the base cover on the base center before assembly.
2. Step 2: Install the casters. Cover the base center with the base cover, and install the gas lift.
3. Step 3: Install the mechanism using M6*22 screws (W x4) and M6*30 screws (V x4). Ensure the 'FRONT' label is oriented correctly.
4. Step 4: Install the footrest and then put on the rubber rings (S x2).
5. Step 5: Place the seat onto the gas lift.
6. Step 6: Install the connector on the chair back using V x4 and X x4 screws. Note the direction of the connector.
7. Step 7: Install the connector into the rear end of the mechanism using V x4 and P x4 screws.
8. Step 8: Align screw holes and install the armrests using Y x4, Q x4, and U x4 screws. Attention: DO NOT tighten all the screws completely until they are fixed in the correct position. Put the washer (u) between the armrest and chair body.
9. Step 9: Attach the headrest (j) and lumbar pillow (k).
10. Step 10: Complete the assembly.

03 Functions Display

Please read the function introduction carefully.

A Height Adjustment

Lift up the "LIFT" lever to adjust the height of the chair, and release the "LIFT" lever at the desired height. Lift your body slightly off the seat when adjusting the height.

B Back Recline Function

Pull up on the "RCL" lever and the back angle tilts independently with user's motion. Push down on the "RCL" lever and the back angle is locked in position. Rest on the back when resetting it to its normal position, otherwise the back may rebound rapidly.

C Massage Function

Plug in USB to enable the massage function of the lumbar pillow.

Frequently Asked Questions

Q: Why do the armrests loosen after a period of use?

A: In most cases, the screws of the armrests and back become loose after a period of use. Re-tightening the screws can fix the problem.

04 SAFETY & MAINTENANCE

Please read the safety introduction carefully.

• ✔️ Sit in the center of the chair with your back to the backrest.
• ❌ DO NOT sit at the front edge of the chair.
• ❌ DO NOT stand on the chair.
• ❌ DO NOT use the chair with more than one person.
• ❌ DO NOT turn the chair around when a person is sitting in it.
• ❌ DO NOT push down on the backrest when a person is reclined.
• ❌ DO NOT place only your back on the chair.

Dear Customer,

Thank you for choosing GTPLAYER. We are dedicated to enriching the gaming and shopping experience for our customers. For safe use, please read this manual before installation and keep it for after use. Feel free to email us if you have any concerns about our products. We will reply within 24 hours.

Important Notes for Service:

• When the product is damaged due to courier problems, please contact our customer service in time for verification.
• We will rectify the issue as soon as possible.
• We offer a 365-day quality assurance.
• We provide a 7-day no-reason return service (Note that the returned product will not affect secondary sales).

We offer product explanations, installation instructions, product maintenance, and maintenance methods.

If you are satisfied with our product and service:

• Please add our store to your favorites.
• Please recommend our products to your friends.
• Please leave your purchase experience in our store or product page.

Feedback and reviews from you will greatly help us offer better services to players around the world.

Best regards!

ATTENTION! During installation, DO NOT tighten all the screws completely until all the screws are fixed in the correct position.